Whirlpool W10562352B Bedienungsanleitung
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Whirlpool W10562352B (2 Seiten) in der Kategorie Trockner. Dieser Bedienungsanleitung war fĂĽr 27 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Gas and Electric Dryer
PRODUCT MODEL NUMBERS
W10848818A
01/18
WED4950HW, WGD4950HW, WED4850HW,
WGD4850HW, YWED4850HW
Installation clearances:
For each arrangement, consider allowing more space for ease of
installation and servicing, spacing for companion appliances, and
clearances for walls, doors, and oor moldings. Space must be
large enough to allow door to fully open. Add spacing on all sides
of dryer to reduce noise transfer. If a closet door or louvered door
is installed, top and bottom air openings in door are required.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
Dryer Dimensions
Front View
503/4"
(1289 mm)
42"
(1067 mm)
281/4"
(717 mm)
281/4"
(717 mm)
NOTE: Minimum height of leveling legs should be 1/2" (13 mm),
or high enough for dryer to match the height of the accompanying
washer.
Side View
29"
(737 mm)
407/8"
(1038 mm)
1/2"
(13 mm)
A B
A. Wide opening side-swing door
B. Wide opening hamper door
Back View
141/2"
(368 mm)
43/4"
(121 mm) 91/4"
(235 mm)
11/4"
(32 mm)
141/2"
(368 mm)
43/4"
(121 mm) 91/4"
(235 mm)
11/4"
(32 mm)
301/4"
(768 mm)
4"
(101 mm)
Non-Steam
Installation spacing for recessed area
or closet
The dimensions shown are for the minimum spacing allowed.
â– Additional spacing should be considered for ease of
installation and servicing.
â–
Additional clearances might be required for wall, door,
and oor moldings.
â– Additional spacing of 1" (25 mm) on all sides of the dryer
is recommended to reduce noise transfer.
â–
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
â– Companion appliance spacing should also be considered.
Installation Spacing
6"/0"
(152 mm/
0 mm)
14" max
(356 mm)
1"/0"
(25 mm/0 mm)
1"/1"
(25 mm/25 mm)
18"/18"
(457 mm/
457 mm)
3"/3"
(76 mm/
76mm)
3"/3"
(76 mm/
76mm)
48" 2
/48"
2
(310 cm2/
310 cm2
)
24"2/
24"2
(155 cm2/
155 cm2)
Recommended/Minimum spacing
Steam
Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.
ELECTRICAL REQUIREMENTS – Gas models only
VENTING REQUIREMENTS
The dryer must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten. Damage to the coupling
can result. A cold water faucet should be located within 4 ft. (1.2 m) of the water ll valves, and should have water pressure of 20–100 psi
(137.9–689.6 kPa). You may use the water supply for your washer using the “Y” connector and short hose, which are provided.
Use a 3- or 4-wire, single-phase, 120/240 volt, 60 Hz, AC-only electrical supply (or 3- or 4-wire, 120/208 volt electrical supply, if specied on the serial/
rating plate) on a separate 30 amp circuit, fused on both sides of the line. Connect to an individual branch circuit. Do not have a fuse in the neutral
or grounding circuit. Do not use an extension cord.
GAS SUPPLY REQUIREMENTS
Gas supply: This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. 3/8"
approved aluminum or copper tubing may be used for lengths under 20 ft (6.1 m) if local codes and gas supplier permit. Lengths over 20 ft (6.1 m)
should use larger tubing and a different size adapter tting. Pipe-joint compounds resistant to the action of L.P. gas must be used. An individual
manual shut-off valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223.1.
WATER (STEAM MODELS ONLY) REQUIREMENTS
INSTALLATION REQUIREMENTS
ELECTRICAL REQUIREMENTS – Electric models only
Use a 3- or 4-wire, single-phase, 120/240 volt, 60 Hz, AC-only electrical supply (or 3- or 4-wire, 120/208 volt electrical supply, if specied on the serial/
rating plate) on a separate 30 amp circuit, fused on both sides of the line. Connect to an individual branch circuit. Do not have a fuse in the neutral
or grounding circuit. Do not use an extension cord.
WARNING: To reduce the risk of re, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Dryer exhaust must not be connected into any gas vent, chimney, wall,
ceiling, attic, crawlspace, or a concealed space of a building. Only rigid
or exible metal vent shall be used for exhausting.
â– Only a 4" (102 mm) heavy metal exhaust vent and clamps
may be used.
â– Do not use plastic or metal foil vent.
Rigid metal vent:
â– Recommended for best drying performance and to avoid crushing
and kinking.
Flexible metal vent :(Acceptable only if accessible to clean)
■Must be fully extended and supported in nal dryer location.
â– Remove excess to avoid sagging and kinking that may result in
reduced airow and poor performance.
■Do not install in enclosed walls, ceilings, or oors.
â– The total length should not exceed 7
3/4 ft. (2.4 m).
NOTE: If using an existing vent system, clean lint from entire length of
the system and make sure exhaust hood is not plugged with lint. Replace
plastic or metal foil vents with rigid metal or exible metal vents. Review
“Vent System Chart” and, if necessary, modify existing vent system to
achieve best drying performance.
Recommended Styles:
Acceptable Style:
Louvered hood Box hood
Angled hood
Determine vent path:
â–
Select route that will provide straightest and most direct path
outdoors.
â– Plan installation to use fewest number of elbows and turns.
â– When using elbows or making turns, allow as much room
as possible.
â– Bend vent gradually to avoid kinking.
■Use as few 90° turns as possible.
Determine vent length and elbows needed for best drying
performance:
â–
Use following “Vent System Chart” to determine type of vent material
and hood combinations acceptable to use.
NOTE: Do not use vent runs longer than those specied in “Vent
System Chart.” Exhaust systems longer than those specied will:
â–
Shorten life of dryer.
â– Reduce performance, resulting in longer drying times and
increased energy usage.
The “Vent System Chart” provides venting requirements that will help
achieve best drying performance.
Number of
90° turns
or elbows
Type
of vent
Box/louvered
hoods
Angled
hoods
0 Rigid metal 64 ft. (20 m) 58 ft. (17.7 m)
1 Rigid metal 54 ft. (16.5 m) 48 ft. (14.6 m)
2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m)
3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m)
4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m)
Vent System Chart
4"
(102 mm)
4" (102 mm) heavy metal exhaust vent
Exhaust hoods:
â–
Must be at least 12" (305 mm) from ground or any object that may
obstruct exhaust (such as owers, rocks, bushes, or snow).
Produktspezifikationen
| Marke: | Whirlpool |
| Kategorie: | Trockner |
| Modell: | W10562352B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Whirlpool W10562352B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Trockner Whirlpool
26 Mai 2024
23 Mai 2024
20 Mai 2024
18 Mai 2024
7 Mai 2024
2 Mai 2024
24 April 2024
20 April 2024
13 April 2024
1 April 2024
Bedienungsanleitung Trockner
- Trockner Sinbo
- Trockner Samsung
- Trockner Clatronic
- Trockner Emerio
- Trockner Coline
- Trockner Medion
- Trockner Nedis
- Trockner Hanseatic
- Trockner LG
- Trockner Adler
- Trockner Camry
- Trockner Trisa
- Trockner Bosch
- Trockner AEG
- Trockner Asko
- Trockner Siemens
- Trockner Bauknecht
- Trockner Electrolux
- Trockner Fagor
- Trockner Gorenje
- Trockner Klarstein
- Trockner Koenic
- Trockner Miele
- Trockner Teka
- Trockner Bomann
- Trockner Vox
- Trockner Mesko
- Trockner Bush
- Trockner Thomson
- Trockner Amica
- Trockner BEKO
- Trockner Grundig
- Trockner Hotpoint
- Trockner Mio Star
- Trockner Schneider
- Trockner Sharp
- Trockner Smeg
- Trockner Tomado
- Trockner AEG-Electrolux
- Trockner Aliomatic
- Trockner Ardo
- Trockner Ariston
- Trockner Aspes
- Trockner Balay
- Trockner Bellavita
- Trockner Blomberg
- Trockner Scandomestic
- Trockner Brandt
- Trockner Candy
- Trockner Castor
- Trockner Comfee
- Trockner Constructa
- Trockner CorberĂł
- Trockner Daewoo
- Trockner Elektra Bregenz
- Trockner ELIN
- Trockner Eudora
- Trockner Eurotech
- Trockner Exquisit
- Trockner Mitsubishi
- Trockner GE
- Trockner Haier
- Trockner Hisense
- Trockner Hoover
- Trockner Hotpoint-Ariston
- Trockner Ignis
- Trockner Indesit
- Trockner Juno
- Trockner Kelvinator
- Trockner Maytag
- Trockner Midea
- Trockner Caple
- Trockner Neff
- Trockner Nordmende
- Trockner Otsein-Hoover
- Trockner Privileg
- Trockner Rommer
- Trockner Saivod
- Trockner ETNA
- Trockner Schulthess
- Trockner Frigidaire
- Trockner SIBIR
- Trockner Speed Queen
- Trockner Svan
- Trockner Thor
- Trockner V-ZUG
- Trockner Vestel
- Trockner Vestfrost
- Trockner Zanker
- Trockner Zanussi
- Trockner Zerowatt
- Trockner Pelgrim
- Trockner Philco
- Trockner Akai
- Trockner Arçelik
- Trockner Continental Edison
- Trockner Tesla
- Trockner ProfiCare
- Trockner Bimar
- Trockner DeLonghi
- Trockner Element
- Trockner Leifheit
- Trockner Ariete
- Trockner Remington
- Trockner Morris
- Trockner Cylinda
- Trockner MPM
- Trockner UPO
- Trockner Thomas
- Trockner Logik
- Trockner Orima
- Trockner Proline
- Trockner Westinghouse
- Trockner Amana
- Trockner Gram
- Trockner Omega
- Trockner Profilo
- Trockner Lamona
- Trockner Kogan
- Trockner Royal Sovereign
- Trockner New Pol
- Trockner Aurora
- Trockner Danby
- Trockner Vedette
- Trockner Auto Joe
- Trockner Ariston Thermo
- Trockner RCA
- Trockner Fisher & Paykel
- Trockner Esatto
- Trockner Gibson
- Trockner CDA
- Trockner General Electric
- Trockner Seiki
- Trockner Defy
- Trockner Jocel
- Trockner Kenmore
- Trockner Lavorwash
- Trockner Magic Chef
- Trockner Marynen
- Trockner Stirling
- Trockner Avanti
- Trockner Kunft
- Trockner Simpson
- Trockner Roper
- Trockner Mabe
- Trockner Amba
- Trockner Classique
Neueste Bedienungsanleitung fĂĽr -Kategorien-
16 August 2024
14 August 2024
13 August 2024
6 August 2024
6 August 2024
1 Juli 2024
1 Juli 2024
30 Juni 2024