Whirlpool ADPU 7443 Bedienungsanleitung

Whirlpool Spülmaschine ADPU 7443

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Whirlpool ADPU 7443 (8 Seiten) in der Kategorie Spülmaschine. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

EN -1-

Chart

(see at right for options description)

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute.

If pressed when the dishwasher is switched off it

drains any possible liquids from dishwasher

(1 minute process).

If the indicator flashes repeatedly, see page 6 -

chapter “What to do if...”.

START/RESUME BUTTON

Push this button to start the selected program:

the indicator lights up and goes off at the end of the

program. When the door is opened during a

washing cycle, the cycle is temporarily paused:

the Start indicator blinks. To resume the cycle

close the door and push Start button again.

PROGRAM SELECTION

BUTTON

Push “Programs” button

(repeatedly) until the indicator

of the required program lights

up (see “Table of programs”

below).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on

conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the

EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

* Power consumption in: Left-on mode: 0.70 W / Off-mode: 0.40 W.

Table of programs Deter-

gent

Consumption Drying

Phase

PPrograms Available

options Loading instructions Litres kWh Minutes1)

1Auto Sensor 50°-65°C Delay

Antibacterial

rinse

Recommended program for

routine washes, with dried-on

food (e.g. EN 50242). X7-15 1.00-1.70 70-172 Full

2Pre-Wash cold Delay Crockery to be washed later. —4.0 0.01 14-16 NO

3Rapid 45°C Delay Lightly soiled crockery, with no

dried-on food. X11.0 0.85 30-50 NO

4Eco2) 50°C Delay

Antibacterial

rinse

Normally soiled crockery.

Standard program the most

efficient in terms of its combined

energy and water consumption . X12.0 1.02 170 Full

5Intensive 65°C Delay

Antibacterial

rinse

Recommended program for

heavily soiled crockery, especially

suitable for pans and saucepans. X15.0 1.60 165-175 Full

5019 300 00740

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

SALT INDICATOR

When lit (at the end of the

cycle), the salt reservoir

needs to be refilled.

DELAYED START

BUTTON

The wash cycle can be

programmed to start

after 2, 4 or 8 hours.

Then press the Start

button. The wash

program will start after

the set time.

RINSE AID INDICATOR

When lit (at the end of the

cycle), the rinse aid

dispenser needs to be

refilled.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

ANTIBACTERIAL RINSE 3)

This function activates an

antibacterial rinse at the end

of the wash cycle,

guaranteeing a further

reduction of bacteria. Press

the button to activate or

deactivate the function. This

function can be used with

the programs indicated in

the table of programs. The

dishwasher door must be

kept shut for the entire

duration of the program in

order to guarantee

reduction of bacteria. If the

door is opened the indicator

lamp starts flashing.

TABLET SETTING

This setting allows to optimize the cycle performances

according the type of detergent used.

Push the Tablet button for 3 seconds (until the indicator

lights up) if you are using the combined detergents in

tablet (rinse aid, salt and detergent in 1 dose).

If you are using powder detergent or liquid detergent,

the Tablet indicator on the control panel has to be off.

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

EN -2-

First time use

5 786

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

1. Ask your water supply company what the water hardness is... 2. ...enter this value on

your dishwasher Suggestions for detergent use

German

degrees °dH French

degrees °fH English

degrees °eH Water hardness

level

3 first PROGRAM LEDs

lit on the panel

(see table of programs)

P1 P2 P3

Gel or Powder

(rinse aid and

salt) Tablets

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4if water is

HARD extra salt

needs to be

added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Water hardness should be set only

before the first wash or if water

hardness has been changed

1Visual indicator

(depending

on the model).

Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness level falls within category

(soft), no salt is required.

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED. green: OK. clear: NEEDS TO

BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

- Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.

- Programs LEDs will indicate the water hardness setting.

- Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.

- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.

Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Water hardness level is factory set

for medium-hard water (level 4).

Even if you use tablets which

include salt functionality, you must

still add regeneration salt since such

detergents are not effective enough

at softening hard water.

At first time use, the salt

reservoir has to be filled

independently from water

hardness level (see

description below in step 1

“Daily check”).

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can

lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

EN -3-

Daily check

Check the rinse aid indicator to check the level

into the dispenser.

(depending on the model)

Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINSE AID NEEDS

TO BE ADDED. dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the

appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty

drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with

rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the

detergent dispenser

prior to starting a

wash program.

Shut the cover

by pressing dedicated ribs.

Insert detergent: Tablet / powder / liquid into the big chamber.