Western Digital VelociRaptor 300GB Bedienungsanleitung

Western Digital Festplatte VelociRaptor 300GB

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Western Digital VelociRaptor 300GB (5 Seiten) in der Kategorie Festplatte. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/5

Internal Desktop

WD VelociRaptor

Quick Install Guide

™

-1-

Congratulations on purchasing a WD VelociRaptor! This document was designed to

aid in the quick installation of your new SATA hard drive. If you experience problems

following these procedures or need further information regarding the installation and

use of your drive, visit our website at support.wdc.com to search our online

knowledge base for frequently asked questions and other common troubleshooting

tips.

Compatibility

Windows® XP/2000/Vista

Note: Compatibility may vary depending on your

hardware configuration and operating system.

System Requirements

• SATA interface connector on motherboard, or

SATA controller card (sold separately) installed in

an available 32-bit PCI expansion slot (2.1- or

2.2-compliant).

• 3.5-inch internal drive bay.

Unpacking & Drive Handling

WD hard drives are precision instruments and

should be handled with care during unpacking and

installation. Hard drives can be damaged by rough

handling, shock and vibration, or electrostatic

discharge (ESD). Be aware of the following

precautions:

• This product contains no user-serviceable parts;

refer servicing to WD-authorized personnel only.

• Do not unpack your hard drive until you are ready

to install it. Your hard drive is packaged in an anti-

static bag.

• To avoid ESD problems, ground yourself by

touching the metal chassis of the computer before

handling the hard drive. Articles of clothing

generate static electricity. Do not allow clothing to

come in direct contact with the hard drive or

circuit board components.

• Handle the hard drive by its sides only. Avoid

touching the circuit board components on the

bottom of the hard drive.

• Do not drop, shake, or knock down the hard drive.

• Do not stack hard drives or stand your WD hard

drive on its edge.

Getting Started

1. Gather these materials and tools: WD hard drive

kit; computer system manual; operating system

manual and DVD or CD; SATA host controller

drivers (if applicable);Phillips and flat-blade

screwdrivers.

2. Before performing any hardware installation, back

up your existing data.

3. Before handling the hard drive or any other

components, discharge static electricity by

touching the metal chassis of your computer or by

using an anti-static wrist strap.

4. Locate and record your WD hard drive serial

number, model number, and date code on the

label on top of your drive.

5. Power off the computer and unplug the power

cord.

6. Remove the system cover (refer to your system

manual for instructions).

Kit Contents

WD Hard Drive*

Documentation

Mounting screws

SATA cable

*Important: The 2.5-inch WD VelociRaptor is

enclosed in a 3.5-inch mounting frame heat sink that

maintains drive temperature. Disassembling these

components will void the warranty.

ENG

-2-

Install the Hard Drive

1. Slide the hard drive into an available 3.5-inch drive bay and

secure the drive with the four mounting screws (two on each

side). For proper grounding, install the screws in the hole

positions (Figure 1).

2. Attach one end of the SATA cable to the SATA interface on the

WD drive (Figure 2). SATA connectors are keyed to ensure

proper insertion.

3. Connect the SATA power cable to the SATA interface on the

drive (Figure 2).

4. Connect the SATA cable to the SATA connector on the

motherboard or the SATA controller card (Figure 3).

Note: If using a SATA controller card, be sure to follow the

instructions that came with the card to install the SATA host

drivers.

5. Verify all cable connections. Replace and secure the system

cover. Reconnect the power cord and power on the computer.

6. Follow the instructions below for your Windows operating

system.

Windows Vista

Windows Vista has all the necessary tools to help you properly

install a SATA drive. Depending on your configuration, follow the

appropriate set of instructions below (Single Install or Adding a

Second Drive).

Note: Ensure your drive is detected by your SATA controller during

bootup or in the SATA BIOS by disconnecting any other hard

drives from the computer system until Windows has been

completely installed on the desired hard drive.

Single Install:

If your SATA controller supports RAID, you may need to define your

drive in a RAID Array before Windows can detect the drive, even if

the motherboard or system drivers are being loaded correctly. This

is true even if installing a single drive. Contact your system or RAID

controller manufacturer for assistance on defining your drive in a

RAID Array.

1. Insert the Windows Vista DVD into the DVD-ROM drive and

restart the system.

2. Follow the onscreen prompts until the Where do you want to

install Windows? screen displays.

3. Your hard drive is listed in the center window screen as “Disk 0

Unallocated Space.”

–If you want a single partition (single drive letter), click Next to

automatically partition and format your hard drive in NTFS.

Windows Vista continues installing.

–If you want multiple partitions on this hard drive, click Drive

options (advanced) and skip to step 5 below.

–If your hard drive is not detected, you may need to obtain third

party SATA controller drivers from the SATA controller

manufacturer. These drivers must be installed from a CD, DVD,

floppy, or USB flash drive.

4. After clicking Drive options (advanced), click New to add a

new partition to the hard drive.

5. Enter the capacity of the partition and click Apply.

Figure 1

Figure 2

SATA device plug

power connector

SATA device plug

interface connector

SATA power

receptacle

connector

SATA receptacle

interface connector

Mounting frame

Figure 3

SATA cable connection

Motherboard

Expansion slot

SATA controller card

SATA Motherboard

Configuration

SATA Controller Card

Configuration

SATA cable

Produktspezifikationen

Marke:	Western Digital
Kategorie:	Festplatte
Modell:	VelociRaptor 300GB
Breite:	101.6 mm
Tiefe:	147 mm
Gewicht:	489 g
Höhe:	26.1 mm
Betriebstemperatur:	0 - 60 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Plug & Play:	Ja
Stromverbrauch (Standby):	4.53 W
Eingebaut:	Ja
Temperaturbereich bei Lagerung:	-40 - 70 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Schnittstelle:	Serial ATA II
Benutzerhandbuch:	Ja
Kompatible Betriebssysteme:	Windows Vista/XP/2000
Stromverbrauch (aus):	0.42 W
Arbeitsspannung:	5 V
HDD Kapazität:	300 GB
HDD Geschwindigkeit:	10000 RPM
HDD Größe:	2.5 "
Höhe bei Betrieb:	-305 - 3050 m
Puffergröße Speicherlaufwerk:	16 MB
Start-/Stopp-Zyklen:	50000
Höhe bei Lagerung:	-305 - 12200 m
Suchzeit (Schreiben):	4.7 ms
Suchzeit (Lesen):	4.2 ms
Durchschnittliche Wartezeit:	5.5 ms
Track to track seek time:	0.7 ms
Schallldruckpegel:	36 dB
Vibrationen in Betrieb:	20-300 Hz, 0.75G G
Vibrationen außer Betrieb:	20-500 Hz, 4.0G G
Bytes pro Sektor:	512
Drive Ready Time:	10 s