Watson C-2E Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Watson C-2E (4 Seiten) in der Kategorie Ladegerät. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Thank you for choosing Watson Pro
Please read this user manual carefully and keep
it for reference before using the charger.
C-AM-2E
C-VM-2E
Dual Position
Li-ion Battery Charger
with DC Output
TM
SAFETY INSTRUCTIONS
Do not store, place, or use the charger where it may come into contact with
excess heat, water, or moisture.
High-voltage internal components present the risk of electrical shock.
Make sure the XLR cable is securely locked into the port before use. You should
hear an audible click.
Charge only at room temperature on a dry, vibration-free surface.
Should you ever notice smoke or a strange odor coming out of the charger,
immediately unplug the AC adapter from the power outlet. Using the charger
under these conditions can cause fire and electric shock.
Do not short-circuit the terminals of your battery or charger.
Do not attempt to disassemble any part of the charger.
Use this charger with Watson Pro batteries only.
The charger, adapters, and batteries may feel warm during the charging process.
This is normal.
Remove any battery after fully charged.
Unplug the AC cable or 4-pin XLR cable from the power outlet and clean the area
around the prongs of the plug when necessary. The presence of dust around the
prongs can cause fire.
ATTACHING AND CHARGING A BATTERY
1. Deploy the charger stand legs, and place the charger on a flat surface.
2. Use the included AC power cable to connect the charger to a power source.
3. Align the 3-stud mount (C-AM-2E) or V-Mount (C-VM-2E) on the battery with the
appropriate slots in the charger.
4. Slide the battery into place to lock. You should hear a click.
5. Flip the charger's power switch to the On position.
CONNECTING DEVICES
1. Use the included 4-pin XLR cable and plug the male end into the charger's DC
output port until it clicks.
2. Plug the other end of the 4-pin XLR cable into your device. This can be a video
camera or monitor as well as lighting fixture.
RELEASING A BATTERY FROM THE CHARGER
1. Press and hold the battery release latch.
2. Slide the battery out, and separate it from the charging plate.
STATUS INDICATORS
STATUS INDICATORS
Off Charger is turned on with no batteries connected. (C-VM-2E)•
Green Charger is turned on with no batteries connected. (C-AM-2E) •
• Battery is fully charged or battery capacity is above 95%.
Red Battery connected with low or no power. •
• Battery is charging.
Flashing red
and green
The charger has detected some problems with the battery or the charger.
For more information, or to arrange service, visit www.poweredbywatson.com or call
Customer Service at 212-594-2120.
8
7
6
5
1. Charging status indicator
1. Power indicator
1. DC output (4-pin XLR)
1. Charger stand (2 legs)×
1. AC input
1. Power switch
1. Battery release latch
2. Battery mount
Included: • AC power cable
4-pin XLR cable •
1 6
5
4
3 8
2 7
1
8
7
4
3
2
DC OUTPUT: The DC output allows you to connect and power devices with a
4-pin XLR cable. When there are no batteries connected to the charger, the
DC output will transfer power at 16.7 V and 4.5 A. When the L or R channel has
a battery connected, the DC output is powered from the batteries, even if the
charger's power switch is in the On position.
4 4 4


Produktspezifikationen

Marke: Watson
Kategorie: Ladegerät
Modell: C-2E

Brauchst du Hilfe?

Wenn Sie Hilfe mit Watson C-2E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Ladegerät Watson

Bedienungsanleitung Ladegerät

Neueste Bedienungsanleitung für -Kategorien-