Volkswagen Tiguan 2015 Bedienungsanleitung
Volkswagen
PKW
Tiguan 2015
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Volkswagen Tiguan 2015 (3 Seiten) in der Kategorie PKW. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/3
Jump-starting
Introduction
In this section you’ll find information about:
Using jumper cables
If your engine does not start because the vehicle battery is dead, your vehicle's battery can be
connected to the battery of another vehicle to start your engine (jump-starting). Check the battery acid
level indicator window before jump-starting ⇒ 12 Volt vehicle battery.
You must use jumper cables that meet recognized industrial standards (check information provided by
the jumper cable manufacturer). For vehicles with gasoline engines, the cross-section of the jumper
cable wire must be at least 0.038 in 2 (25 mm2), or about 3 ga. (AWG).
More information:
Working in the engine compartment
12 Volt vehicle battery
WARNING
Working on the batteries or the electrical system in your vehicle can cause serious acid
burns, fires, or electrical shock.
Always keep children away from battery acid and vehicle batteries in general.
Sulfuric battery acid is very corrosive and can cause blindness and damage to
unprotected skin. Never let battery acid or lead particles contact your eyes, skin, and
clothing.
Never lean over a vehicle battery. Always wear protective gloves and eye protection. To
reduce your risk of injury, never tilt the batteries; acid could spill out through the vents and
burn you.
A highly explosive mixture of gases is given off when the battery is being charged.
Always avoid fires, sparks, open flame, and smoking. Never create sparks or electrostatic
charges when handling cables and electrical equipment. Never short-circuit the battery
terminals. High-energy sparks can cause serious personal injury.
If you get battery acid in your eyes or on your skin, immediately rinse with cold water for
several minutes and get medical attention immediately. If you swallow any battery acid, get
medical attention immediately.
WARNING
Improper use of jumper cables when jump-starting a vehicle with a dead battery can cause
the battery to explode, leading to serious personal injury. To help reduce the risk of battery
explosion:
All work on the batteries or the electrical system in your vehicle can cause serious acid
burns, fires, or electrical shocks. Always read and heed the following WARNINGS and safety
precautions before working on the batteries or the electrical system ⇒
⇒
⇒
⇒ ⇒ 12 Volt vehicle
battery.
Always make sure that the battery providing starting assistance (the booster battery) has
the same voltage as the dead battery (12 V) and about the same amperage capacity (see
battery label).
Never jump-start a vehicle with a thawed or frozen vehicle battery. The battery can
explode. A dead battery can freeze at temperatures around +32 °F (0 °C).
A battery that is frozen or was frozen, but has since thawed, must be replaced.
When the vehicle battery is jump-started, it gives off hydrogen gas, which is highly
explosive! Always keep fire, sparks, open flame, and smoking materials far away from vehicle
batteries. Never use a mobile telephone while connecting or disconnecting jumper cables.
Jump-start batteries only in well-ventilated areas. Batteries give off highly explosive
hydrogen gas during jump-starting.
Always route the jumper cables so that they cannot get caught in any moving parts in the
engine compartment.
Never short out the battery terminals by connecting the positive terminal (+) and negative
(-) terminals with each other.
Never connect the negative cable from the other vehicle directly to the negative terminal
of the dead battery, as this may cause the hydrogen gas given off by the dead battery to
explode.
Never attach the negative cable from the vehicle providing starting assistance to any part
of the fuel system or to the brake hoses or brake lines.
Never allow the non-insulated parts of the battery clamps to touch.
Never allow the jumper cable attached to the positive battery terminal to contact metal
parts of the vehicle.
Always follow the instructions of the jumper cable manufacturer.
NOTICE
To help prevent extensive damage to the vehicle electrical system, read and heed the
following:
Connecting jumper cables improperly can cause a short circuit and do expensive damage
to the vehicle's electrical system.
Do not let the vehicles touch each other while the jumper cables are connected. If they do,
electrical current may flow between the vehicles when the positive (+) terminals are connected,
causing electrical system damage.
Using jumper cables
Fig. 211 Diagram for attaching the jumper cables: Dead battery 1 and booster battery 2.
Please first read and note the introductory information and heed the WARNINGS
The dead battery must be properly connected to the vehicle's electrical system.
Make certain that the vehicles are not touching each other. Otherwise, electric current could flow as
soon as the positive terminals (+) are connected. Use longer jumper cables if necessary.
The clamps on the jumper cables must have good contact to bare metal on the battery terminals.
If the engine does not start, stop the process after 10 seconds and repeat after about one minute.
The procedure for attaching and for removing the jumper cables is described below. Perform each of
the following steps only in the order described, which follow the letters shown in the illustration
⇒ fig. 211 A – B – C – D.
Attaching the jumper cables
1. Switch off the ignition in both vehicles.
2. If necessary, open the battery cover in the engine compartment ⇒ 12 Volt vehicle battery.
3. Attach one end of the red jumper cable to the positive terminal (+) of the dead battery (1) ⇒ .
4. Attach the other end of the red jumper cable to the positive terminal (+) of the good battery
(booster battery) (2).
5. Attach one end of the black jumper cable to the negative terminal (–) of the booster battery:
Battery (2) ⇒ fig. 211.
6. Attach the other end of the black jumper cable (3) to a bare metal part of the vehicle with the
dead battery. This part should be connected directly to the engine block. You may also attach the
cable to the engine block itself. Attach the clamp to a point that is as far away as possible from the
dead battery (1) ⇒ .
7. Route the jumper cables so that they cannot get caught in any moving parts in the engine
compartment of either vehicle.
Starting the engine
Start the engine of the vehicle with the good battery that is providing help and let it run at idle
speed.
Turn the ignition of the vehicle with the dead battery. If the engine starts, wait 2 to 3 minutes until it
“runs smoothly” before removing the jumper cables as described below ⇒ . If the engine does not
start within about 10 seconds, turn off the ignition and wait at least one minute; then try again.
Produktspezifikationen
| Marke: | Volkswagen |
| Kategorie: | PKW |
| Modell: | Tiguan 2015 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Volkswagen Tiguan 2015 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung PKW Volkswagen
27 April 2023
27 April 2023
27 April 2023
27 April 2023
27 April 2023
27 April 2023
27 April 2023
27 April 2023
27 April 2023
27 April 2023
Bedienungsanleitung PKW
Neueste Bedienungsanleitung für -Kategorien-
27 April 2023
30 April 2023
30 April 2023
30 April 2023
27 April 2023
30 April 2023