Vimar 03991 Bedienungsanleitung

Vimar Schalten 03991

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Vimar 03991 (3 Seiten) in der Kategorie Schalten. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Viale Vicenza, 14

36063 Marostica VI - Italy

www.vimar.com

03991-03992EN 03 2209

03991

03992

00932

00945.G

03991 - Magnetic Quid relay module with sequential ON/OFF pulses,

1 input for NO push button, 1x10 A 220-240 V~ 50/60 Hz relay output,

installation in junction boxes or connector block boxes.

The device, which can be installed in connector block boxes and placed under-

neath the blank module or inside the junction boxes declared as suitable for electri-

cal devices that dissipate energy, turns a load on or off following a signal received

from a push button.

03992 - Magnetic Quid relay module with sequential ON/OFF pulses,

1 input for NO push button, 1 input for reset push button, 1x10 A

relay output, 220-240 V~ 50/60 Hz power supply, light signal for the

load status on each individual push button, installation in junction

boxes or connector block boxes.

The device, which can be installed in connector block boxes and placed under-

neath the blank module or inside the junction boxes declared as suitable for electri-

cal devices that dissipate energy, turns a load on or off following a signal received

from a push button. It is also fitted with an input for the control unit switch-off

control (reset). If the signalling unit 00932 is installed in the ON/OFF or reset control

push button, the device sends a signal about the status of the load.

00945.G, 00932 - Load status LED signalling unit, green.

The signalling unit is installed in the back of the push buttons associated with relay

03992 and signals the status of the load both for the control push button and for

the reset push button. Art. 00945.G is dedicated to the Linea series.

CHARACTERISTICS.

• Art. 03991:

- Rated supply voltage: 220 – 240 V~ 50/60 Hz.

- ON/OFF control via NO push buttons.

- Max. 1 switching per second.

- It should be used in dry, dust-free places at a temperature of between 0 °C and

+35 °C.

- Dissipated power: 1.5 W with load ON and max. current 10 A

0 W and no absorption with load OFF

• Art. 03992:

- Rated supply voltage: 220 – 240 V~ 50/60 Hz.

- ON/OFF control via NO push buttons.

- Max. 1 switching per second.

- Reset control via NO push button. An unlimited number of art. 03992 (with or

without signalling unit) can be connected to the same Reset push button.

- Art. 00932 for signalling the load status can be installed on the control and reset

push button.

- An unlimited number of ON/OFF control push buttons can be connected to

each module 03992. Up to a maximum of 4 ON/OFF control push buttons with

junction box pilot lamp can be connected. This lamp will only light up when the

load is ON.

- Up to a maximum of 2 Reset push buttons with junction box pilot lamp can be

connected to each module 03992 (for instance, with 2 modules 03992 con-

nected to the same Reset push buttons, 4 Reset push buttons with junction

box pilot lamp can be connected). The junction box pilot lamp will light up if one

of the relays has the load ON.

- On the ON/OFF control push button and on the reset push button we recommend

you use buttons art. 31000A.L-31000.L-31000A.D-31000.D if you are using

signalling unit 00945.G or buttons 20026-19026-14026-20021.L-19021.L-

14021.L if you are using unit 00932.

- In the event that several modules 03992 are connected together using the

reset push button, the system must be set up with a single Hysteresis and/

or RCBO circuit breaker.

- It should be used in dry, dust-free places at a temperature of between 0 °C and

+35 °C.

- Dissipated power: 1.5 W with load ON and max. current 10 A

0 W and no absorption with load OFF

• Art. 00945.G-00932:

- Rated supply voltage: 220 – 240 V~ 50/60 Hz.

- The signalling unit can be installed on the ON/OFF and reset control push but-

ton.

- The signalling unit can also be installed on controls that are not associated with

module 03992.

- It should be used in dry, dust-free places at a temperature of between 0 °C and

+35 °C.

WEEE - User information

The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life

must be collected separately from other waste. The user must therefore hand the equipment at the end of its

life cycle over to the appropriate municipal centres for the differentiated collection of electrical and electronic

waste. As an alternative to independent management, you can deliver the equipment you want to dispose of

free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also deliver

electronic products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to

electronics distributors with a sales area of at least 400 m 2. Proper sorted waste collection for subsequent

recycling, processing and environmentally conscious disposal of the old equipment helps to prevent any pos-

sible negative impact on the environment and human health while promoting the practice of reusing and/or

recycling materials used in manufacture.

CONTROLLABLE LOADS.

• Relay output (220- 240 V~ controllable loads):

- rated load in AC1: 10 A (6,000 cycles);

- rated load in AC15: 2.2 A (5,000 cycles);

- resistive loads : 10 A (20,000 cycles);

- incandescent lamps : 3 A (20,000 cycles);

- fluorescent lamps : 100 W (20,000 cycles);

- energy saving lamps : 100 W (20,000 cycles);

- LED lamps : 100 W (20,000 cycles);

- electronic transformers : 2 A (20,000 cycles);

- power supply units for LED strips: 200 W (20,000 cycles).

INSTALLATION RULES.

• Installation must be carried out by qualified persons in compliance with the cur-

rent regulations regarding the installation of electrical equipment in the country

where the products are installed.

• The power supply circuit (L-N) must be protected against overloads by installing

a device, fuse or automatic 1-way switch, with a rated current not exceeding 10

• Since these are retrofit devices, art. 03991 and 03992 must always be installed

in protected boxes.

REMOTE CONTROL RECEPTION.

Quid can be remote controlled using the following devices:

• DueFili+ video door entry system: Video Door App + art. 40507 + art. 69RH or

69PH (programmed for 2 s timed actuation)

The DueFili+ system is designed to configure a timed actuation (relay art. 69RH

or 69PH) and control it from video door entry indoor stations. If the indoor station

is connected (art. 40507) actuation can be remote controlled via the Video Door

App.

• IP video door entry system: Video Door App + art. 40607 + art. 40636 (pro-

grammed for 2 s timed actuation)

The IP video door entry system is designed to configure a timed actuation (relay

art.40636) and control it from video door entry indoor stations. If the indoor sta-

tion is connected (art. 40507) actuation can be remote controlled via the Video

Door App.

• GSM thermostat 01913: the device is fitted with a programmable output to which

an auxiliary supporting relay needs to be connected (a common one-position

stable relay with a 230V coil is sufficient). Actuation is then controlled via the

By-Phone App or the By-Clima App (or directly via SMS text message).

REGULATORY COMPLIANCE.

LV Directive. EMC directive. EN 60669-2-1 standard.

REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces

of lead.

Viale Vicenza, 14

36063 Marostica VI - Italy

www.vimar.com

03991-03992EN 03 2209

1P L

00936.250..

Important: Do not connect the indicator light to the control in parallel.

03991 CONNECTIONS

ON/OFF push button

CONNECTION OF VISIBLE IN DARKNESS PUSH BUTTON

03991

1P L R+ P+ 1 L

03992

000

MA D E IN I TALY

30008

000

MA D E IN I TALY

30008

000

MA D E IN I TALY

30008

P+ R+ o

Eikon - Arké - Plana

10 mm

220-240V~

00932

TS 4915

10A 250 V~ L 1

A005248

00932

220-240V~

10 mm

20008 - 19008 - 14008

10mm

P+ R+ o

30008

00945.G

00932

03992 CONNECTIONS WITH 00945.G or 00932 UNIT

If unit 00945.G or 00932 is inserted into the ON/OFF control push button or the Reset push button of relay 03992, the status of the load is displayed on the individual push button; if the unit is

on, the load is powered, whereas if it is off the load is not powered. The terminals of the push buttons are polarised so the installer must take care to identify the P+/R+ terminal and the Neutral

terminal as illustrated in the figure (inverted wiring will result in malfunctioning).

P = ON/OFF push button input

1 = Load Output

L = Line

R+ = Reset push button input

P+ = ON/OFF push button input

1 = Load Output

L = Line

Viale Vicenza, 14

36063 Marostica VI - Italy

www.vimar.com

03991-03992EN 03 2209

R+ P+ 1 L

00936.250..

R+ P+ 1 L

* Only in the presence of signalling unit 00932. If this is not the case, an unlimited number of push buttons can be connected. Use only the signalling unit 00932 as other indicator lights could damage