TP-Link TL-SG1210P Bedienungsanleitung

TP-Link Schalter TL-SG1210P

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für TP-Link TL-SG1210P (3 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 63 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Connection

Installation Guide

Gigabit Desktop Switch with PoE/PoE+

LED Explanation

Power

On: Power on

O: Power o

Link/Act (For TL-SG1008P)

On: A device is linked to the correspoding

port and running properly.

Flashing: Transmitting or receiving data.

O: No device is linked to the

corresponding port.

Link/Act, Uplink 1, Uplink 2 (For TL-SG1210P)

Green On: Running at 1000 Mbps, but no activity.

Green Flashing: Running at 1000 Mbps and is

transmitting or receiving data.

Yellow On: Running at 10/100 Mbps, but no activity.

Yellow Flashing: Running at 10/100 Mbps and is

transmitting or receiving data.

O: No device is linked to the corresponding port.

Package Contents: Switch, Power Adapter, Power Cord and Installation Guide.

On: Providing PoE power

Flashing: PoE fault

O: Not providing PoE power

PoE Status

On: Running at 1000 Mbps.

O: Running at 10/100 Mbps or no device

is linked to the corresponding port.

1000Mbps (For TL-SG1008P)

PoE MAX

For TL-SG1008P:

On: 48 W≤Total power supply < 55 W

Flashing: Total power supply ≥ 55 W

O: Total power supply < 48 W

For TL-SG1210P:

On: 56 W≤Total power supply < 63 W

Flashing: Total power supply ≥ 63 W

O: Total power supply < 56 W

Note: For simplicity, we will take TL-SG1008P for example throughout the Guide.

IP Camera AP

Ethernet Ports (1-8)

PoE Ports (1-4)

IP Phone

PoE Devices

Router

LAN PortWAN Port

Internet

DC P er Adapterow

AC Power Cord

Note:

PoE/PoE+ ports typically connect to PoE Devices. Besides, PoE/PoE+ ports can also connect to non-PoE devices, but only transmit data.

TL-SG1210P has two uplink ports, which typically connect to uplink devices like routers.

Uplink 1 is an SFP port and works with a 1000 Mbps SFP module. Uplink 2 is an RJ45 port.

For TL-SG1008P, maximum PoE power is 15.4 W for each PoE port and 55 W for all PoE ports in total.

For TL-SG1210P, maximum PoE power is 30 W for each PoE port and 63 W for all PoE ports in total.

4. PoE budget calculations are based on laboratory testing. Actual PoE power budget is not guranteed and will vary as a result of client

limitations and environmental factors.

Frequently Asked Questions (FAQ)

The Power LED should be lit when the power system is working normally.

If the Power LED is not lit, please try the following:

A1:

Make sure the AC power cord is connected to the switch with power

source properly.

A2:

Make sure the voltage of the power supply meets the requirements

of the input voltage of the switch.

A3: Make sure the power source is ON.

Q1. Why is the Power LED not lit?

Please try the following:

A1:

Make sure that the cable connectors are rmly plugged into the

switch and the device.

Make sure the connected device is turned on and works normally.

The cable must be less than 100 meters long (328 feet).

Q2. Why is the Link/Act LED not lit while a device is

connected to the corresponding port?

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

0 C to 40 C (32 F to 104˚ ˚ ˚ ˚F)

-40 C to 70 C (-40 F to 158˚ ˚ ˚ ˚F)

10% to 90%RH non-condensing

5% to 90%RH non-condensing

Environmental and Physical Specications

IEEE 802.3i, 802.3u, 802.3ab, 802.3x, 802.3af, 802.1p

For TL-SG1210P: IEEE 802.3z, 802.3at

CSMA/CD

For TL-SG1008P:

8 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation

MDI/MDIX;

PoE Ports: Port 1-Port 4, Total Power Supply: 55 W

For TL-SG1210P:

9 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation

MDI/MDIX; 1 1000 Mbps SFP port;

PoE Ports: Port 1-Port 8, Total Power Supply: 63 W

10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);

EIA/TIA-568 100 Ω STP (maximum 100 m)

100BASE-TX: UTP category 5, 5e cable (maximum 100 m);

EIA/TIA-568 100 Ω STP (maximum 100 m)

1000BASE-T: UTP category 5e cable or above (maximum

100 m); EIA/TIA-568 100 Ω STP (maximum 100 m)

1000BASE-SX/LX/LX10/BX10: MMF, SMF (For

TL-SG1210P)

For TL-SG1008P: 16 Gbps

For TL-SG1210P: 20 Gbps

Store-and-Forward

Automatically learning, automatically aging

External Power Adapter

Input: 100-240 V AC, 50/60 Hz

Output:

For TL-SG1008P: 48 V DC/1.25 A

For TL-SG1210P: 53.5 V DC/1.31 A

Standard

General Specications

Specications

Q3. Why is PoE/PoE+ ports not supplying power for PoE devices?

If total power consumption of connected PoE devices exceeds the maximum, the

system will cut o the power to ports with the lowest PoE priority. A PoE port with

a smaller index number has a higher PoE priority. Let’s take TL-SG1008P as an

example. If port 1, 2 and 4 are consuming 15.4 W respectively, and an additional

PoE device with 12 W is connected to port 3, the total power consumption

exceeds 55 W, so the system will cut o the power to port 4.

Power Supply

MAC Address Learning

Transfer Method

MAC Address Table

Backbone Bandwidth

Network Media (Cable)

Interface

Protocol

For technical support and other information, please visit

https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides,

welcome to email techwriter@tp-link.com.cn.

To ask questions, find answers, and communicate with TP-Link

users or engineers, please visit https://community.tp-link.com

to join TP-Link Community.

Wall Mountable For TL-SG1008P: No

For TL-SG1210P: Yes

Distance Between

Mounting Holes For TL-SG1210P: 150 mm

FCC compliance information statement

限用物質含有情況標示聲明書

限用物質及其化學符號

鉛

鎘

汞

六價鉻

CrVI

多溴聯苯

PBB

多溴二苯醚

PBDE

產品元件名稱

PCB

外殼

電源供應器

備考系指該項限用物質之百分比含量未超出百分比含量基準值。1. “ “

備考系指該項限用物質為排除項目。2. “ “

BSMI Notice

安全諮詢及注意事項

請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

注意防潮，請勿將水或其他液體潑灑到本產品上。

插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Explanation of the symbols on the product label

DC voltage

AC voltage

Class II equipment

Polarity of output terminals

Energy eciency marking

Indoor use only

RECYCLING

This product bears the selective sorting symbol for Waste

electrical and electronic equipment (WEEE). This means that this

product must be handled pursuant to European directive

2012/19/EU in order to be recycled or dismantled to minimize its

impact on the environment.

User has the choice to give his product to a competent recycling

organization or to the retailer when he buys a new electrical or

electronic equipment.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Safety Information

Adapter shall be installed near the equipment and shall be easily accessible.

Place the device with its bottom surface downward.

Do not use any other chargers than those recommended.

Keep the device away from water, re, humidity or hot environments.

Do not use damaged charger or USB cable to charge the device.

Do not attempt to disassemble, repair, or modify the device.

Please read and follow the above safety information when operating the device.

We cannot guarantee that no accidents or damage will occur due to improper use

of the device. Please use this product with care and operate at your own risk.

Note: The product label can be found at the bottom of the product.

Product Name: 8-Port Gigabit Desktop Switch with 4-Port PoE /

10-Port Gigabit Desktop Switch with 8-Port PoE+

Model Number: TL-SG1008P/TP-SG1210P

Component Name Model

T480125-2-DT (For TL-SG1008P)

T535131-2-DT (For TP-SG1210P)

I.T.E. Power Supply

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Consult the dealer or an experienced radio/ TV technician for help.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit dierent from that to

which the receiver is connected.

Product Name: I.T.E. Power Supply

Model Number: T480125-2-DT/T535131-2-DT

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: sales.usa@tp-link.com

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на

відповідність вимогам нормативних документів та вимогам, що передбачені

чинними законодавчими актами України.

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

CE Mark Warning

Canadian Compliance Statement

This is a class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

TP-Link hereby declares that the device is in compliance with the essential

requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU,

2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at

https://www.tp-link.com/en/ce.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt

RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may

cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences et Développement économique

Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes:

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

We, TP-Link USA Corporation, has determined that the equipment shown as

above has been shown to comply with the applicable technical standards, FCC

part 15. There is no unauthorized change is made in the equipment and the

equipment is properly maintained and operated.

Issue Date: 2019/12/02

Produktspezifikationen

Marke:	TP-Link
Kategorie:	Schalter
Modell:	TL-SG1210P
Breite:	209 mm
Tiefe:	126 mm
Produktfarbe:	Grau
Höhe:	26 mm
Energiequelle:	Gleichstrom
Betriebstemperatur:	0 - 50 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Verpackungsbreite:	315 mm
Verpackungstiefe:	240 mm
Verpackungshöhe:	70 mm
Netzstandard:	IEEE 802.1p,IEEE 802.3af,IEEE 802.3at,IEEE 802.3x
Quality of Service (QoS) Support:	Ja
Zertifizierung:	CE, FCC, RoHS
Power over Ethernet (PoE):	Ja
Warentarifnummer (HS):	85176990
Stromverbrauch (max.):	78.13 W
Betriebsanleitung:	Ja
Gehäusematerial:	Metall
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-40 - 70 °C
Luftfeuchtigkeit bei Lagerung:	5 - 90 %
Switch-Typ:	Unmanaged
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	9
Basic Switching RJ-45 Ethernet Ports-Typ:	Gigabit Ethernet (10/100/1000)
Auto MDI/MDI-X:	Ja
10G-Unterstützung:	Nein
Kupfer Ethernet Verkabelungstechnologie:	10BASE-T,100BASE-TX,1000BASE-T
MAC-Adressentabelle:	4000 Eintragungen
Routing-/Switching-Kapazität:	20 Gbit/s
Anzahl Gigabit Ethernet (Kupfer) Anschlüsse:	9
IGMP snooping:	Ja
Eingangsspannung:	53.5 V
Eingangsstrom:	1.31 A
Store-and-Forward:	Ja
Auto-Negotiation-Funktion:	Ja
Netzteil enthalten:	Ja
Wärmeableitung:	266.42 BTU/h
Menge SFP-Modul-Steckplätze:	1
Anzahl Power over Ethernet plus (PoE+) Anschlüsse:	8
Gesamtleistung Power over Ethernet (PoE):	63 W
Ventilatorlos:	Ja
Selbstlernen von MAC-Adressen unterstützt:	Ja
Auto-Alterung von MAC-Adressen unterstützt:	Ja
Ethernet-Kabel Verkablungstechnologie:	1000BASE-X
Fibertyp:	Einzelmodus