SpinMaster Hyper Actives Stunt - Air Hogs Bedienungsanleitung

SpinMaster Spielzeug Hyper Actives Stunt - Air Hogs

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SpinMaster Hyper Actives Stunt - Air Hogs (2 Seiten) in der Kategorie Spielzeug. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Contents:

• 1 x Hyper Actives Stunt™

• 1 x Controller/Charger

• 1 x Instruction Guide

1. Open the battery door with a

screwdriver (not included).

2. If used batteries are

present, remove these

batteries from the unit by

pulling up on one end of

each battery.

3. Install new batteries as

shown in the polarity

diagram (+/-) inside the

battery compartment.

4.Replace battery door

securely.

5. Check your local laws

and regulations for correct

recycling and/or battery

disposal.

INSTALLING/REPLACING THE BATTERIES

HOW TO CHARGE YOUR HYPER ACTIVES STUNT™

USING THE CONTROLLER/CHARGER

Battery

Compartment

Cover

Battery

Compartment

6 x

1.5V AA

Alkaline

Batteries

• Controller/charger requires

6 x 1.5V AA alkaline

batteries (not included).

• Batteries are small objects.

• Replacement of batteries

must be done by adults.

• Follow the polarity (+/-)

diagram in the battery

compartment.

• Promptly remove dead

batteries from the toy.

• Dispose of used batteries

properly.

• Remove batteries for

prolonged storage.

• Only batteries of the same

or equivalent type as re-

commended are to be used.

• DO NOT incinerate used

batteries.

• DO NOT dispose of

batteries in fire, as batteries

may explode or leak.

• DO NOT mix old and new

batteries.

• DO NOT mix different types

of batteries, i.e.: alkaline/

standard (carbon-zinc) or

rechargeable batteries.

• DO NOT use rechargeable

batteries.

• DO NOT recharge

non-rechargeable batteries.

• DO NOT short-circuit the

supply terminals.

• DO NOT store your car

or controller near heat or in

direct sunlight.

BATTERY SAFETY INFORMATION

Left/Right

8-10YRS

CHG OFF ON

1. Turn vehicle OFF.

2. Turn controller/charger OFF.

3. Open charge door to access

charge cable.

4. Open charge port cover located

on the side of the vehicle.

5. Carefully push the charge plug

all the way into the vehicle’s

charge port.

6. Set the controller/charger switch

to CHG.

7. The red charging light will turn

on and charging will begin when

it starts to flash. After 30 to 50

minutes the charging will be

complete and the red charge

light and green power light will

both start to flash.

8. When charging is complete,

turn controller/charger OFF.

9. Carefully remove the

charge plug from the vehicle’s

charge port.

10. Close the charge port cover.

11. Wrap charge cable starting

at tab indicated then close

charge door.

CHG OFF ON

8 9 10 11

5 6 7

2 3

INSTRUCTIONS

Controller/Charger

Hyper Actives

Stunt™

Forward/

Reverse Power Light

Charge Light

CHG/OFF/ON

Switch

Spin Button

Turbo Button

Cover and

Charge Cable

Impact

Bumper

Charge

Port

ON/OFF

Switch

Over-sized

Tires

Forward/Reverse, Left/Right

1. Turn vehicle ON.

2. Turn controller/charger ON.

3. The left stick controls

the vehicle’s forward and

reverse driving.

4. To move the vehicle to the right

push the right stick to the right.

5. To move the vehicle to the left

move the right stick to the left. 4 5

CHG OFF ON

2 3

rim Knob

NOTE: 1. If the charge light and power light are flashing alternatively while

charging, there may be a bad cable connection. Check that cable and plug

are connected correctly and repeat charging steps 1 to 6.

2. The remote control will automatically shut off after idling for about

5 minutes. To reactivate turn off and on.

3. When the remote control is in either ON status or CHARGE status and

the green power light is flashing, it means that the battery level is low

and the batteries need to be replaced.

WARNING:

CHOKING HAZARD – Small parts.

Not for Children under 3 years.

Contains LiPo battery pack. • Battery pack must be recycled or disposed of properly.

• If at any time in the future you should need to dispose of this product please note

that Waste Electrical Products should NOT be disposed of with household waste.

Please recycle where facilities exist. Check with your Local Authority or retailer for

recycling advice. (Waste Electrical and Electronic Equipment Directive).

Warning:

CHOKING HAZARD –

Small Parts.

product conforms to safety requirements of ASTM F-963, EN-71 & CHPA. • Please retain

this information for future reference. • Please remove all packaging materials before

giving to children. • An adult should periodically check this toy to ensure no damage

or hazards exist, if so, remove from use. • Children should be supervised during play.

• Keep addresses and phone numbers for future reference. • The item inside this

package may vary from the photographs and/or illustrations. MADE IN CHINA.

20037619, 20037620 GEN REV 0

T20416_0002_20037619_GEN_IS_R1

Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada

Customer Care: 1-800-622-8339 Fax: 416-364-8005

Email: customercare@spinmaster.com

Spin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville,

NY 14221, USA

Spin Master Toys Far East Limited, Rm #1113, 11/F,

Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E., Kowloon, HK

SPIN MASTER INTERNATIONAL, S.A.R.L., 16 AVENUE PASTEUR, L-2310, LUXEMBOURG

www.spinmaster.com

TROUBLESHOOTING GUIDE

Vehicle is slow or will not move.

Vehicle does not drive in a

straight line.

My vehicle and/or controller is dirty.

Vehicle is not responding or driving

on it’s own.

1. Batteries in the controller need to be

replaced if green power light is flashing.

2. Vehicle is out of range of controller.

3. There is hair or debris stuck in the wheels

or wheel axles.

4. Batteries are installed incorrectly.

5. Improper surface for vehicle.

6. Controller not aimed at vehicle or

objects interfering with signal.

7. Controller was inactive for 30 seconds

or more and turned itself off to preserve

your batteries.

Vehicle requires wheel alignment.

1. Inappropriate driving surface.

2. Dirty hands.

1. Using another vehicle controller/

charger of the same frequency.

2. Infrared interference from another source.

3. Bright lights may be affecting the

IR control.

1. Replace batteries in the controller with new, fresh batteries.

2. Move closer to the vehicle.

3. With the vehicle and controller turned off, have an adult carefully remove the hair

or debris from the wheels or wheel axles.

4. With the vehicle and controller turned off, have an adult check that the batteries

are installed correctly in the controller.

5. Indoor play only on hard surfaces. Examples of poor play surfaces are thick

carpet, grass or sand. Examples of good play surfaces are non-carpeted floors,

flat tile floors or flat wooden floors.

6. Point controller IR at the vehicle. Ensure there are no objects blocking the

controller “line of sight” to the vehicle.

7. Re-set both vehicle and controller OFF to ON.

Refer to Trim Adjustment guide above.

Ensure the controller and vehicle are off. Have an adult remove the

batteries first and replace the battery cover. Slightly dampen a clean cloth in water

and wipe toy clean. Wipe dry. DO NOT IMMERSE IN WATER and DO NOT USE

ANY CHEMICALS. Let the toy completely dry before putting batteries back into

clean, dry battery compartment.

1. Only use the controller/charger supplied with this vehicle.

2. Do not operate vehicle around devices that emit other infrared signals.

3. Avoid driving near windows or bright lights or choose another place to operate

the vehicle.

PROBLEM CAUSE SOLUTION

NOTE: If normal function of the product is disturbed or interrupted, strong

electro-magnetic interference may be causing the issue. To reset product, turn it

completely off, then turn it back on. If normal operation does not resume, move the

product to another location and try again. To ensure normal performance, change

the batteries, as low batteries may not allow full function.

Your Hyper Actives Stunt™ is equipped with a Lithium Polymer battery.

SPECIAL LIPO BATTERY INSTRUCTIONS:

• Never charge battery unattended. • Charge battery in isolated area. Keep away from

flammable materials. • Do not expose to direct sunlight. • There is a risk of the batteries

exploding, overheating, or igniting. Do not disassemble, modify heat, or short-circuit the

batteries. Do not place them in fires or leave them in hot places. • Do not drop or subject to

strong impacts. • Do not allow the batteries to get wet. • Only charge the batteries with the

specified Spin Master™ battery charger. • Only use the batteries in the device specified by

Spin Master™. • Carefully read the instruction guide, and use the batteries correctly. • In the

unlikely event of leakage or explosion use sand or a chemical fire extinguisher for the battery.

• Batteries must be recycled or disposed of properly.

PRODUCT BATTERY REMOVAL INSTRUCTIONS: Internal battery is factory installed, product disassembly

and battery removal must be performed by an adult. Do not use any tools for disassembly. Pulling, tearing,

and deforming of the product during disassembly, while necessary, should be as limited as possible. Do not

compress the product at any time. Ensure product is turned off. Find a point where the two body halves

meet; the front or back or sides of the vehicle. Start to peel the halves apart, separating them where they are

glued together; remove any tape as necessary. Separate product body halves to expose internal electronics.

To separate battery from product use scissors to cut a single battery wire, immediately wrap the cut wire

end with tape to isolate it, repeat until all battery wires are cut and isolated. Dispose of battery in accordance

with your local battery recycling or disposal laws. NOTE: Opening of product and/or removal of battery will

render product inoperative and voids manufacturer warranties, dispose of remaining product components in

accordance with local laws.

VEHICLE TRIM ADJUSTMENT

PERFORMING SPINS

ONCE YOU’RE FINISHED PLAYING

If the vehicle is not driving

straight when you push the

forward/reverse stick forward,

use the trim knob to correct

the problem.

1. If the vehicle turns to the left,

slowly turn the trim knob to

the right until the vehicle

drives straight.

2. If the vehicle turns to the

right, slowly turn the trim knob

to the left until the vehicle

drives straight.

Pressing the spin button while the

vehicle is moving/accelerating causes

the vehicle to spin. In some cases,

depending in speed, direction and

surface condition the vehicle may flip

over. Because the vehicle can run on

either side you can just keep driving.

CHG OFF ON

TURBO ACCELERATION

Pressing the turbo

button increases

the speed of the

vehicle.

Turn vehicle OFF.Turn controller/charger OFF.

This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference to radio communications. Because this toy generates, uses, and can radiate radio frequency energy, there can be no guarantee that

interference will not occur. If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this toy does cause interference to radio or television reception (you can

check this by turning the toy off and on while listening for the interference), one or more of the following measures may be useful: • Reorient or relocate the receiving antenna • Increase the separation between the toy

and the radio or the TV • Consult the dealer or an experienced TV-radio technician for help. NOTE: Changes, adjustments or modifications to this unit, including but not limited to, replacement of any transmitter component

(crystal, semiconductor, etc.) could result in a violation of FCC rules under part 15 and/or 95 and must be expressly approved by Spin Master Ltd. or they could void the user’s authority to operate the equipment.

CANADIAN Class B statement: This class B digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.