Sony ZS-PS55 Bedienungsanleitung

Sony Radio ZS-PS55

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony ZS-PS55 (2 Seiten) in der Kategorie Radio. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

4-576-951-11(1)

Personal Audio System

Operating Instructions

ZS-PS55B

*   and VOL +  have a tactile dot.

The unit is not disconnected from the AC power

source (mains) as long as it is connected to the wall

outlet, even if the unit itself has been turned off.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Excessive sound pressure from earphones and

headphones can cause hearing loss.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

The nameplate is located on the bottom exterior.

Basic Operations

Before using the unit

To turn the power on or off

Press OPERATE (or POWER) . You can also turn on

the power of this unit using the direct power-on

function (below).

In this manual, operations are mainly explained

using the direct power-on function.

To use the direct power-on function

Press CD , USB , DAB/FM , AUDIO IN  or

FAVORITE RADIO STATIONS (1-3)  while the unit is

turned off. The power turns on with the relevant

function selected.

To adjust the volume

Press VOL + or 

To listen through headphones

Connect headphones to the (headphones) jack 

.

Playing a music disc

1 Press CD  to turn on the CD function.

2 Press PUSH OPEN/CLOSE , place a disc in

the CD compartment and then close the

compartment cover.

Label side up

The disc is loaded and the disc information

appears on the display.

To Do this

Find a point in a

track/file

(fast forward/

rewind)

Hold down  or  

during playback, and release the

button at the desired point.

When locating a point while

paused, press   to start

playback after the desired point

is found.

* In program play mode, playback starts from the first

programmed track/file.

Tip

To cancel the Resume Play, press

  while the CD is

stopped.

Note

Resume Play is cancelled in the following cases:

 When you open the CD compartment.

 When you turn off the power.

Example of folder structure and playing order

The playing order of the folders and files is as

follows. However, the playing order may differ from

the original order on the disc, depending on the

recording method used.

Folder

MP3/WMA file

Notes on MP3/WMA discs

 When a disc is loaded, the unit reads all the files on that

disc. During this time, “READING” is flashing. If there are

many folders or non-MP3/WMA files on the disc, it may

take a long time for play to begin or for the next MP3/

WMA file to start to play.

 We recommend that non-MP3/WMA files or unnecessary

folders are excluded when creating MP3/WMA discs.

 During playback, audio files other than MP3 and WMA

files are skipped even if those files are included in a folder.

 The audio formats supported by this unit are as follows:

MP3: File extension “.mp3”

WMA: File extension “.wma”

Note that even if the file name has the correct file

extension but the actual file was created in a different

audio format, this unit may produce noise or may

malfunction.

 MP3 PRO format is not supported.

 WMA files encoded in WMA DRM, WMA Lossless and

WMA PRO formats cannot be played back.

 This unit cannot play audio files on a disc in the following

cases:

When the total number of audio files exceeds 999.

When the total number of folders on a single disc

exceeds 256 (including the “ROOT” folder).

When the directory level (folder depths) exceeds 8

(including the “ROOT” folder).

 Folder names can be displayed with up to 32 characters,

including quotation marks.

 File names can be displayed with up to 32 characters,

including quotation marks and file extensions.

 Characters and symbols that cannot be displayed by the

unit will appear as “_”.

 This unit conforms to version 1.0, 1.1, 2.2, 2.3 and 2.4 of the

ID3 tag format for MP3 files and the WMA tag format

defined by the ASF specification (Advanced Systems

Format) for WMA files. When a file has the ID3 or WMA tag

information, the song title, artist name, and album name

will be displayed. If a file does not have the tag

information, the unit displays as follows:

File name instead of the song title.

“NO ARTIST” message instead of the artist name.

“NO ALBUM” message instead of the album name.

ID3 and WMA tag information can be displayed up to 64

characters.

Audio CD

Total number of tracks

Total playing time

MP3/WMA disc

Total number of folders*

* If MP3/WMA files are present only in the root directory

(“ROOT” folder), “1FLDR” appears on the display.

3 Press   to start playback.

Track number or MP3/WMA

file number

Playing time

When you play an MP3/WMA disc, the folder

name*1 and song title are displayed before the

playing time*

2 appears.

*1 If MP3/WMA files are present only in the root directory,

“ROOT” appears on the display.

*2 If the playing time is longer than 100 minutes, “--:--”

appears on the display.

Other operations

To Do this

Pause playback Press  . To return to

playback, press the button

again.

Stop playback Press  . When you press 

 after playback is stopped,

playback starts from the point

where you stopped playback

(Resume Play)*.

Select a folder

on an MP3/WMA

disc

Press + or .

Select a track/

file

Press  or  . You can

skip tracks/files one by one.

WARNING

To reduce the risk of fire, do not cover the ventilation

opening of the appliance with newspapers,

tablecloths, curtains, etc. Do not expose the

appliance to naked flame sources (for example,

lighted candles).

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing, and

do not place objects filled with liquids, such as

vases, on the apparatus.

As the main plug is used to disconnect the unit from

the mains, connect the unit to an easily accessible

AC outlet. Should you notice an abnormality in the

unit, disconnect the main plug from the AC outlet

immediately.

Power Sources

Connect the AC power cord , or insert six R14 (size C) batteries (not supplied) into the battery compartment .

To a wall outlet

To AC IN

AC power cord (supplied)

Rear

Notes

 When using the radio on batteries and the battery power drops to a certain level, the OPR/BATT indicator

 dims or power of

the radio may go off during playback. If this happens, replace all the batteries with new ones. Even after the OPR/BATT indicator

 becomes dim, you can use the radio function for some time, although you cannot use the CD player. Before you replace the

batteries, be sure to remove any CD and disconnect any USB devices or optional components from the unit.

 To use the unit on batteries, disconnect the AC power cord from the unit and the wall outlet.

 In standby mode with the AC power cord connected, “STANDBY” appears on the display.

To use the power-management function (European models only)

This unit is equipped with an automatic standby function. With this function, the unit enters standby mode

automatically after about 15 minutes if there is no operation or audio signal output.

To turn standby mode on or off, press VOL  while holding down TUNE + . Each time you press the buttons,

“AUTO STANDBY ON” or “AUTO STANDBY OFF” appears on the display.

Notes

 The displayed content starts flashing on the display about 2 minutes before entering standby mode.

 The automatic standby function is not available with the FM function.

 In the DAB function, if “NOSIGNAL” or “OFF-AIR” remains displayed for 15 minutes, the unit enters standby mode automatically.

Listening to music on a USB device

You can listen to audio files stored on a USB device

(a digital music player or USB storage media).

Audio files in MP3, WMA and AAC formats* can be

played on this unit.

* Files with copyright protection (Digital Rights

Management) cannot be played on this unit.

Compatible USB devices

Compatibility requirements for the USB devices are

as follows. Before using a device with this unit,

check that it meets the requirements.

 Compliance with USB 2.0 (Full Speed)

 Supports Mass Storage mode*

* Mass Storage mode is a mode that allows a USB device to

become accessible to a host device, enabling file

transfers. Most USB devices support Mass Storage mode.

1 Connect the USB device to the (USB) port .

2 Press USB  to turn on the USB function.

The volume label is displayed once, then the total

number of folders appears on the display.

Total number of folders

3 Press   to start playback.

The folder name and song title are displayed, and

then the file number and playing time appear.

File number

Playing time*

* If the playing time is longer than 100 minutes, “--:--”

appears on the display.

Other operations

To Do this

Pause playback Press  . To return to

playback, press the button

again*1

Stop playback Press  . When you press 

 after playback is stopped,

playback starts from the point

where you stopped playback

(Resume Play)*2.

Select a folder Press + or .

Select a file Press  or  . You can

skip files one by one.

To skip files continuously, hold

down  or   and

release the button at the desired

file.

Find a point in a

file

(fast forward/

rewind)

Hold down  or  

during playback, and release the

button at the desired point.

When locating a point while

paused, press   to start

playback after the desired point

is found.

When playing a VBR MP3/WMA/AAC file, playback may

restart from a different point.

In program play mode, playback starts from the first

programmed file.

Note

When removing a USB device, hold down

  until

“NODEV” appears, and then turn off the unit or switch to

other functions beforehand. Removing the USB device

without performing these steps may corrupt the data on the

USB device or damage the device itself.

Example of folder structure and playing order

The playing order of the folders and files is as

follows. However, the playing order may differ from

the original order on the USB device, depending on

the recording method used.

Folder

USB device

MP3/WMA/AAC file

Notes on the USB device

 It may take a long time before playback starts when:

 the folder structure is complex.

 the USB device is close to capacity.

 When a USB device is connected, the unit reads all the

files on the device. If there are many folders or files on the

device, it may take a long time for the unit to finish

reading them.

 Do not connect a USB device to the unit through a USB

hub.

 With some connected USB devices, after an operation is

performed, there may be a delay before it is performed by

this unit.

 This unit may not support all the functions provided with

a connected USB device.

 Do not save non-MP3/WMA/AAC files or unnecessary

folders to a USB device that contains MP3/WMA/AAC files.

 During playback, audio files other than MP3, WMA and

AAC files are skipped even if those files are included in a

folder.

 The audio formats supported by this unit are as follows:

 MP3: file extension “.mp3”

 WMA: file extension “.wma”

 AAC: file extension “.m4a,” “.3gp” and “.mp4”

Note that even if the file name has the correct file

extension but the actual file was created in a different

audio format, this unit may produce noise or may

malfunction.

 MP3 PRO format is not supported.

 WMA files encoded in WMA DRM, WMA Lossless and

WMA PRO formats cannot be played back.

 AAC files encoded in copyright-protected AAC format

cannot be played back.

 This unit supports the AAC-LC (AAC Low Complexity)

profile.

 This unit cannot play audio files on a USB device in the

following cases:

 When the total number of audio files in a single folder

exceeds 999.

 When the total number of audio files on a single USB

device exceeds 5,000.

 When the total number of folders on a single USB

device exceeds 256 (including the “ROOT” folder).

 When the directory level (folder depths) exceeds 8

(including the “ROOT” folder).

These numbers may vary depending on the file and folder

structure.

 Compatibility with all encoding/writing software is not

guaranteed. If audio files on the USB device were

originally encoded with incompatible software, those files

may produce noise or interrupted sound, or may not be

played back at all.

 Folder names can be displayed with up to 32 characters,

including quotation marks.

 File names can be displayed with up to 32 characters,

including quotation marks and file extensions.

 Characters and symbols that cannot be displayed by the

unit will appear as “_”.

 This unit conforms to version 1.0, 1.1, 2.2, 2.3 and 2.4 of the

ID3 tag format for MP3 files, the WMA tag format defined

by the ASF specification (Advanced Systems Format) for

WMA files, and the AAC tag format for AAC files.

When a file has the ID3, WMA or AAC tag information, the

song title, artist name, and album name will be displayed.

If a file does not have the tag information, the unit

displays as follows:

File name instead of the song title.

“NO ARTIST” message instead of the artist name.

“NO ALBUM” message instead of the album name.

ID3, WMA and AAC tag information can be displayed up to

64 characters.

Listening to the radio

1 Press DAB/FM  repeatedly to turn on the

radio function and select the “DAB” or “FM”

band.

Reception of DAB/DAB+ radio station

When you press DAB/FM  for the first time

after you purchase the unit, DAB auto tune

starts automatically and creates a list of

available services. During DAB auto tune, the

progress indicator flashes on the display. Do

not press any buttons during DAB auto tune.

Scanning will be interrupted and the service

list may not be created properly.

2 Perform tuning.

For tuning to a DAB/DAB+ station

Press TUNE + or  repeatedly to tune to the

desired station.

“SC” flashes on the display when the selected

primary station has a secondary service. Press

TUNE + or  to tune to the secondary service.

“SC” lights up when a secondary service is

received.

For tuning to an FM station

Hold down TUNE + or  until the frequency

digits begin to change on the display.

The unit automatically scans the radio

frequencies and stops when it finds a clear

station.

If you cannot tune to a station using automatic

tuning mode, press TUNE + or  repeatedly to

change the frequency step by step.

When an FM stereo broadcast is received, “ST”

lights up on the display.

Note

The unit of frequency of tuned stations is MHz.

Notes on DAB/DAB+ stations

 When tuning to a DAB/DAB+ station, it may take a few

seconds before you hear any sound.

 Primary service is automatically received when secondary

service ends.

 This tuner does not support data services.

To make low sounds clear for DAB/DAB+

reception

The DRC (Dynamic range control) function makes

low sounds clear even when you turn the volume

down.

Check that the DAB/DAB+ station you are listening

to conforms to DRC.

1 Hold down PLAY/FM MODE  until “DRC x”

appears on the display.

2 Press TUNE + or  to select “2,” “1” (default

setting) or “0.5.”

To turn off the DRC function, select “0.”

3 Press ENTER .

To run the DAB auto tune manually

If you have moved to another area, perform the DAB

auto tune manually and re-register the contents of

broadcasts.

Hold down DAB/FM  until “INITIAL” and “SCAN?”

appear alternately on the display, and then press

ENTER .

Scanning begins. Depending on the DAB/DAB+

services available in your area, scanning may take a

few minutes.

When scanning is complete, a list of available

services is created.

Notes

 If your country or region does not support DAB/DAB+

broadcasts, “NOSIGNAL” appears on the display.

 The currently stored list of available services will be

cleared once the DAB auto tune process has started.

To improve radio reception

Use the radio in a place where

radio signals can be easily

received such as near a window.

Also, adjust the antenna for good

reception.

Adjust the antenna to

improve FM reception. If the

stereo FM reception is noisy,

press FM MODE  repeatedly

until “MONO” appears on the

display. You will lose the

stereo effect, but the

reception will be improved.

If the reception problem still persists, try changing

the installation location.

Avoid places such as the following:

Between buildings

Nearby mobile

phones, electrical

appliances

On steel desks

or tables

Presetting stations to FAVORITE

RADIO STATIONS

You can preset up to three favorite stations to

FAVORITE RADIO STATIONS (1-3) buttons. Assign one

DAB or FM program for each button.

1 Press DAB/FM  repeatedly to turn on the

radio function and select the band “DAB” or

“FM.”

2 Tune to the station you want to preset.

3 Press and hold the desired FAVORITE RADIO

STATIONS (–SET) (1-3) button  until you hear

a beep.

The tuned station is preset to the selected button

of FAVORITE RADIO STATIONS (1-3) and the same

number as that of the button will light up on the

display.

(Example: Presetting FM 87.50 MHz to number )

To change the preset station

Repeat steps 1 to 3.

The preset station on the button will be replaced by

the new one.

Listening to preset stations with

FAVORITE RADIO STATIONS

Press the desired FAVORITE RADIO STATIONS (1-3)

button .

Note

To prevent the preset from being changed by mistake, do

not hold down the button. If doing so, the preset on the

button will be replaced by the currently tuned station.

For customers in Europe

Notice for customers: the following

information is only applicable to

equipment sold in countries applying EU

directives

This product has been manufactured by or on behalf

of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. Inquiries related to product

compliance based on European Union legislation

shall be addressed to the authorized representative,

Sony Deutschland GmbH, Hedelfinger Strasse 61,

70327 Stuttgart, Germany. For any service or

guarantee matters, please refer to the addresses

provided in the separate service or guarantee

documents.

Disposal of waste batteries and electrical

and electronic equipment (applicable in

the European Union and other European

countries with separate collection

systems)

This symbol on the product, the battery

or on the packaging indicates that the

product and the battery shall not be

treated as household waste. On certain

batteries this symbol might be used in

combination with a chemical symbol.

The chemical symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more than

0.0005% mercury or 0.004% lead. By ensuring these

products and batteries are disposed of correctly, you

will help prevent potentially negative consequences

for the environment and human health which could

otherwise be caused by inappropriate waste

handling. The recycling of the materials will help to

conserve natural resources.

In case of products that for safety, performance or

data integrity reasons require a permanent

connection with an incorporated battery, this battery

should be replaced by qualified service staff only. To

ensure that the battery and the electrical and

electronic equipment will be treated properly, hand

over these products at end-of-life to the applicable

collection point for the recycling of electrical and

electronic equipment. For all other batteries, please

view the section on how to remove the battery from

the product safely. Hand the battery over to the

applicable collection point for the recycling of waste

batteries. For more detailed information about

recycling of this product or battery, please contact

your local Civic Office, your household waste

disposal service or the shop where you purchased

the product or battery.

Personal Audio System is designed to be used

for playing back music sources on CDs or USB

devices and listening to radio stations.

Downloaded from www.vandenborre.be

Using the display

Checking the information of an audio CD

Press   twice to cancel Resume Play.

The total number of tracks and total playing time

appear on the display.

Checking MP3/WMA/AAC file information

Press DISPLAY  repeatedly while playing an

MP3/WMA file on the disc or an MP3/WMA/AAC

file on the USB device.

The display changes as follows:

Song title ( )*1, 2





Artist name ( )*1



Album name ( )*1



Current file number and playing time*3

*1 If the file does not have corresponding ID3, WMA or AAC

tag information, the file name, “NO ARTIST,” and “NO

ALBUM” scroll on the display instead of the song title,

artist name, and album name.

The function name is displayed for 2 seconds before the

song title appears.

The artist name or album name changes to this after a

few seconds or when the scrolling completes.

Checking the radio information

Press DISPLAY  repeatedly while listening to

the radio.

The display changes as follows:

When listening to FM

Preset number*1 Frequency

When listening to DAB

Preset number*1 DLS (Dynamic Label Segment)*2

 PTY label*2 (see “PTY (programme type)” in

“Specifications”) Ensemble label*2 Channel  

Bit rate*3 Signal level*3 Component label

Press   to return to the normal display.

*1 A preset number is displayed only when you are listening

to the preset radio station.

“NO DLS,” “NO PTY” or “NOSIGNAL” may appear if no DLS,

no PTY label or no ensemble label is received.

“---” may appear if no bit rate or no signal level is

received.

Selecting play mode

You can set the unit to play tracks or files repeatedly

or in random order while a disc/USB device is

stopped.

Press PLAY MODE  repeatedly.

Each time you press the button, the indication

changes as follows:

Normal play (None)





Single repeat ( 1)



All repeat ( )



Selected folder play ( )*



Selected folder repeat play ( , )*



Shuffle play ( )



Program play (PGM)



Program repeat play ( , PGM)

* These functions are available only when playing MP3/

WMA files on an MP3/WMA disc or MP3/WMA/AAC files

on a USB device.

Playing tracks/files repeatedly (Repeat

Play)

You can set the unit to repeatedly play CD-DA tracks

on an audio CD, MP3/WMA files on a CD-R/CD-RW

disc, or MP3/WMA/AAC files on a USB device in

normal, folder and program play modes.

1 Press CD  or USB  to turn on the CD or

USB function.

2 Proceed as follows.

To repeat Do this

A single track/

file

1 Press PLAY MODE 

repeatedly until “ 1” appears.

2 Press  or   to select

a track/file that you want to

repeat.

3 Press  

All tracks/files 1 Press PLAY MODE 

repeatedly until “ ” appears.

2 Press  

A selected folder

on an MP3/WMA

disc or USB

device

1 Press PLAY MODE 

repeatedly until “ ” and “ ”

appear.

2 Select a folder by pressing +

or .

3 Press  

Other Operations To repeat Do this

Programmed

tracks/files

1 Program tracks/files (see

“Creating your own program

(Program Play)”).

2 Press PLAY MODE  until

“PGM” and “ ” appear on the

display.

3 Press  .

To cancel Repeat Play

Press   to stop playback, and then press PLAY

MODE  repeatedly until “ 1”) disappears ” (or “

from the display.

Playing tracks/files in random order

(Shuffle Play)

You can set the unit to play CD-DA tracks on an

audio CD, MP3/WMA files on a CD-R/CD-RW disc or

MP3/WMA/AAC files on a USB device in random

order.

1 Press CD  or USB  to turn on the CD or

USB function.

2 Press PLAY MODE  repeatedly until “ ”

appears on the display.

3 Press   to start Shuffle Play.

To cancel Shuffle Play

Press   to stop playback, and then press PLAY

MODE  repeatedly until “ ” disappears from the

display.

Tip

During Shuffle Play, you cannot select the previous track/file

by pressing .

Creating your own program (Program

Play)

You can arrange the playing order of up to 25

tracks/files on a disc/USB device.

1 Press CD  or USB  to turn on the CD or

USB function.

2 Press PLAY MODE  repeatedly until “PGM”

appears on the display.

3 Press  or  to select a track/file.

When you want to specify a folder that contains

MP3/WMA/AAC files, press + or  first to

select a folder, and then press or    to

select a file.

4 Press ENTER .

The track/file is programmed.

The program step number appears, followed by

the total playing time.

(Example: audio CD)

Step number

Last programmed track number

Total playing time*

* “--:--” appears when programming an MP3/WMA

disc/USB device or when the total playing time is

longer than 100 minutes.

5 Repeat steps 3 and 4 to program additional

tracks/files.

6 Press   to start Program Play.

To play the same program again, press .

Note that the created program is cleared in the

following cases:

When you open the CD compartment.

When you connect another USB device.

When you turn off the power of the unit in the

CD function.

Note

If you try to program 26 tracks/files or more, “FULL” flashes

on the display.

To display programmed track/file

information

After creating your own program, you can check

information about programmed tracks/files.

Press DISPLAY 

repeatedly and the display

changes as follows:

Total number of steps Last programmed track/

file number and the total playing time*

* “--:--” appears for MP3/WMA discs and USB devices, or

when the total playing time is longer than 100 minutes.

To cancel Program Play

Press   to stop playback, and then press PLAY

MODE  repeatedly until “PGM” disappears from

the display.

To delete all tracks/files in the current

program

Stop playback, and then press . “NO STEP”

appears and you can create a new program,

following the procedure “Creating your own

program (Program Play).”

Presetting radio stations

You can store radio stations in the unit’s memory.

You can preset up to 30 radio stations, 20 for FM and

10 for DAB.

Presetting FM stations automatically

1 Press DAB/FM  repeatedly to turn on the

radio function and select the “FM” band.

2 Hold down DAB/FM  until “AUTO” flashes on

the display.

3 Press ENTER  to store the station.

The stations are stored in memory from lower

frequencies to higher ones.

Presetting radio stations manually

You can manually tune in and store the radio

frequencies of desired stations.

1 Press DAB/FM  repeatedly to select a band.

2 Tune to the desired station.

3 Hold down ENTER  until “DAB-xx” or “FM-xx”

flashes on the display.

(Example: DAB)

4 Press PRESET + or  until the preset

number for the station you want flashes on

the display.

5 Press ENTER  to store the station.

If another station is already assigned to the

selected preset number, that station is replaced

by the new one.

Tip

The preset radio stations remain in the unit’s memory even

in the following situations.

The AC power cord is unplugged.

The batteries are removed.

Listening to preset radio stations

1 Press DAB/FM  repeatedly to turn on the

radio function and select the “DAB” or “FM”

band.

2 Press PRESET + or  to select a stored

preset number for the desired radio station.

Using the Sleep Timer

You can set the unit to turn off automatically after a

set time has elapsed.

1 Press SLEEP .

The default setting (“90”) appears and the

“SLEEP” indicator lights up on the display.

2 Press SLEEP  repeatedly to select the

desired setting.

Each time you press the button, the duration (in

minutes) changes on the display, and the

selected setting is confirmed automatically after

about 4 seconds.

Tip

You can check the time left until the unit turns off by

pressing SLEEP  again after setting the sleep timer.

Connecting optional components

You can enjoy the sound from an optional

component, such as a portable digital music player,

through the speakers of this unit.

Be sure to turn off the power of each component

before making any connections.

For details, refer to the instruction manual of the

component to be connected.

1 Connect the AUDIO IN jack  to the line

output jack of the portable digital music

player or other component using an audio

connection cable (not supplied).

2 Turn the connected component on.

3 Press AUDIO IN  and start playing sound on

the connected component.

The sound from the connected component is

output from the speakers.

To connect the unit to a TV or video recorder/

player, use an extension cable (not supplied) with

a stereo-mini jack on one end and two phono

plugs on the other end.

“ ”OVER CURRENT appears and the unit

turns off automatically.

 An abnormal level has been detected in the

electrical current from the (USB) port . In this

case, remove the USB device from the (USB) port 

 and reconnect the USB device, and then turn

on the unit again. If this problem persists after

turning on the power of the unit, contact your

nearest Sony dealer.

There is no sound.

 The USB device may be connected incorrectly.

Turn off the unit and reconnect the USB device.

Then turn on the unit.

There is noise, skipping, or distorted sound.

 Turn off the unit and reconnect the USB device.

Then turn on the unit again.

 The music data itself contains noise, or the sound

is distorted. Noise may have entered during the

creation of audio files. Try re-creating audio files

and use them to play on this unit.

The USB device cannot be connected to the

(USB) port .

 The connector on the USB device or the USB cable

is being inserted backwards. Insert it to the

(USB) port  in the correct direction.

“ ”READING is displayed for an extended

time, or it takes a long time before playback

starts.

 The reading process can take a long time in the

following cases:

 There are many folders or files on the USB

device.

 The file structure is complex.

 The memory is almost full.

 The internal memory is fragmented.

To avoid the above problems, we recommend that

you adhere to the following guidelines:

 Keep the total number of folders on a USB

device to 100 or less.

 Keep the total number of files per folder to 100

or less.

Erroneous display

 The data stored on the USB device may be

corrupted. Send the music data to the USB device

again.

 This unit can display only numbers and letters of

the alphabet. Other characters will not be

displayed correctly.

The USB device is not recognized.

 Turn off the unit and reconnect the USB device,

then turn on the unit.

 The USB device is not functioning properly. Refer

to the USB device operation manual for details on

how to deal with this problem.

Play does not start.

 Turn off the unit and reconnect the USB device.

Play does not start from the first track.

 Set the play mode to Normal Play.

MP3/WMA/AAC files cannot be played

back.

 The audio files may have inappropriate file

extensions. The file extensions supported by this

unit are as follows:

 MP3: file extension “.mp3”

 WMA: file extension “.wma”

 AAC: file extension “.m4a,” “.3gp” and “.mp4”

 The audio files may have been created in formats

other than MP3/WMA/AAC formats.

 The USB storage device uses a file system other

than FAT16 or FAT32.*

 The files are encrypted or protected by passwords.

* This unit supports FAT16 and FAT32, but some USB storage

media may not support both file systems.

For details, refer to the operation manual of the USB

storage device in question or contact the manufacturer.

Radio

The sound is weak or reception is poor.

 Replace all the batteries with new ones.

 Move the unit away from nearby TVs.

 Extend the antenna to its full length, and reorient

it for best reception.

 If you are in a building, listen near a window.

 If a mobile phone is placed close to the unit, a

loud noise may be heard from the unit. Keep the

phone away from the unit.

The TV picture is unstable.

 If you are listening to an FM program near a TV

with an indoor antenna, move the unit away from

the TV.

DAB/DAB+ radio stations are not received

properly.

 Perform the DAB auto tune procedure (see “To run

the DAB auto tune manually”).

 The current DAB/DAB+ service may not be

available. Press TUNE + or  to select a

different service.

 If you have moved to another area, some

services/frequencies may have changed and you

may not be able to tune to your usual broadcast.

Perform the DAB auto tune procedure to

re-register the contents of broadcasts. (Performing

this procedure clears all previously stored presets.)

After trying the suggested remedies, if the problem

persists, unplug the AC power cord or remove all the

batteries. After all the indications on the display

disappear, plug in the AC power cord again, or

re-insert the batteries. If the problem persists,

consult your nearest Sony dealer.

Precautions

Discs that this unit CAN play

 Audio CD (CD-DA*1 tracks)

 CD-R/CD-RW that contains MP3/WMA files and is

finalized*2 correctly.

*1 CD-DA is the abbreviation for Compact Disc Digital Audio.

It is a recording standard used for audio CDs.

*2 Finalizing is the process to make the CD-R/CD-RW discs

playable on the consumer disc player products, and the

finalizing can be enabled or disabled as optional settings

during disc creation in most recording software.

Discs that this unit CANNOT play

 CD-R/CD-RW other than those recorded in audio

CD format or formats conforming to ISO9660

Level 1/Level 2 or Joliet

 CD-R/CD-RW of poor recording quality, CD-R/

CD-RW with scratches or that is dirty, or CD-R/

CD-RW recorded using an incompatible recording

device

 CD-R/CD-RW that is unfinalized or finalized

incorrectly

Notes on discs

 Clean the CD with a cleaning cloth if

the disc is dirty. Wipe the disc from

the center out. If there are scratches,

dirt or fingerprints on the disc, a

tracking error may occur.

 Do not use solvents such as

benzine, thinner, commercially

available cleaners or anti-static

spray intended for vinyl LPs.

 Do not expose the CD to direct sunlight or heat

sources such as hot air ducts, or leave it in a car

parked in direct sunlight as there can be a

considerable rise in temperature inside the car.

 Do not stick paper or a sticker on the CD, or

scratch the surface of the CD.

 After playing, store the CD in its case.

Note on DualDiscs

 A DualDisc is a two sided disc product which

mates DVD recorded material on one side with

digital audio material on the other side. However,

since the audio material side does not conform to

the Compact Disc (CD) standard, playback on this

product is not guaranteed.

Music discs encoded with copyright

protection technologies

 This product is designed to playback discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

by some record companies. Please be aware that

among those discs, there are some that do not

conform to the CD standard and may not be

playable by this product.

On safety

 As the laser beam used in the CD player section is

harmful to eyes, do not attempt to disassemble

the casing. Refer servicing to qualified personnel

only.

 Should any solid object or liquid fall into the unit,

unplug the unit, and have it checked by qualified

personnel before operating it any further.

 Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do not

use such discs.

On power sources

 For AC operation, use the supplied AC power cord;

do not use any other cord.

 Unplug the unit from the wall outlet if it is not to

be used for an extended period of time.

 When not using the batteries, remove them to

avoid damage that can be caused by battery

leakage or corrosion.

On placement

 Do not leave the unit in a location near heat

sources, in a place subject to direct sunlight,

excessive dust or mechanical shock, or in a car

subject to the direct rays of the sun.

 Do not place the unit on an inclined or unstable

surface.

 Do not place anything within 10 mm of the rear of

the cabinet. The ventilation openings must be

unobstructed for the unit to operate properly and

prolong the life of its components.

 Since a strong magnet is used for the speakers,

keep personal credit cards using magnetic coding

or spring-wound watches away from the unit to

prevent possible damage from the magnet.

On operation

 If the unit is brought directly from a cold to a

warm location, or is placed in a very damp room,

moisture may condense on the lens inside the CD

player section. Should this occur, the unit will not

operate properly. In this case, remove the CD and

wait about an hour for the moisture to evaporate.

On handling the unit

 Do not leave the CD compartment open to avoid

dust and debris contamination.

On cleaning the cabinet

 Clean the cabinet, panel and controls using a soft

cloth slightly moistened with a mild detergent

solution. Do not use any type of abrasive pad,

scouring powder, or solvent, such as alcohol or

benzine.

If you have any questions or problems concerning

your unit, consult your nearest Sony dealer.

Specifications

CD player section

System

Compact disc digital audio system

Laser diode properties

Emission duration: Continuous

Laser output: Less than 44.6μW

(This output is the value measurement at a distance of

200 mm from the objective lens surface on the optical

pick-up block with 7mm aperture.)

Number of channels

Frequency response

20Hz 20,000Hz +1/–2dB

Wow and flutter

Below measurable limit

Radio section

Frequency range

DAB (Band-III): 174.928 MHz 239.200 MHz

FM: 87.5 MHz 108 MHz (50 kHz step)

DAB (Band-III) frequency table (MHz)

Channel Frequency Channel Frequency

5A 174.928 10A 209.936

5B 10B 211.648176.640

5C 178.352 10C 213.360

5D 180.064 10D 215.072

6A 181.936 11A 216.928

6B 183.648 11B 218.640

6C 185.360 11C 220.352

6D 187.072 11D 222.064

7A 188.928 12A 223.936

7B 12B 225.648190.640

7C 192.352 12C 227.360

7D 194.064 12D 229.072

8A 195.936 13A 230.784

8B 197.648 13B 232.496

8C 199.360 13C 234.208

8D 201.072 13D 235.776

9A 202.928 13E 237.488

9B 204.640 13F 239.200

9C 206.352

9D 208.064

Antenna

Telescopic antenna

Input

AUDIO IN

Stereo mini jack

 (USB) port

Type A, maximum current 500mA, USB 2.0 Full Speed

compatible

Output

 (headphones) stereo mini jack

For 16  32 impedance headphones

Supported audio formats

Supported bit rates

MP3 (MPEG 1 Audio Layer-3):

32kbps 320kbps, VBR

WMA:

48kbps 192kbps, VBR

AAC*:

8kbps 320kbps, VBR

* USB function only

Sampling frequencies

MP3 (MPEG 1 Audio Layer-3):

32/44.1/48kHz

WMA:

32/44.1/48kHz

AAC*:

32/44.1/48kHz

* USB function only

General

Speaker

Full range, 8cm dia., 6, cone type (2)

Power output

2.0W + 2.0W (at 6, 10% harmonic distortion)

Power requirements

230 V AC, 50 Hz (AC power supply)

9 V DC (6 R14 (size C) batteries)

Power consumption

15W

0.9W (during standby mode)

Battery Life*

1, *2

Playback of CD

Approx. 7 hours

Playback of USB device

Approx. 7 hours (at 100 mA load)

Approx. 3.5 hours (at 500 mA load)

DAB reception

Approx. 7 hours

FM reception

Approx. 11.5 hours

Measured by Sony standards. The actual battery life

may vary depending on the circumstances of the unit

or operating conditions.

*2 When using Sony alkaline batteries.

Dimensions

Approx. 300mm × 125mm × 210.5mm (W/H/D) (incl.

projecting parts)

Mass

Approx. 2 kg (incl. batteries)

Supplied accessories

AC power cord (1)

Design and specifications are subject to change without

notice.

Troubleshooting

General

The power does not turn on.

 Make sure the AC power cord is connected to the

wall outlet securely.

 Make sure the connector of AC power cord is

inserted into the AC IN jack securely.

 Check if the batteries are inserted correctly,

matching the polarities.

 Replace all the batteries with new ones when the

OPR/BATT indicator  dims.

There is no sound.

 Make sure the appropriate function is selected for

the music or sound source you want to listen to.

 Unplug the headphones when listening through

speakers.

The sound is noisy.

 Is someone using a mobile phone or other

equipment emitting radio waves near the unit? If

so, move the unit away from such devices.

A small humming noise is heard.

 This is not a malfunction. You may hear a small

humming noise depending on the status of the

power supply.

“NOT IN USED” appears.

 You pressed an invalid button.

CD/MP3/WMA player

The CD player does not play even when a

CD is in place.

 Place the CD with the label side up.

 Clean the CD.

 Take out the CD and leave the CD compartment

open for about an hour to dry moisture

condensation.

 The CD-R/CD-RW is blank or unfinalized.

 There are no playable MP3/WMA files on the disc.

 There is a problem with the quality of the CD-R/

CD-RW, recording device or application software.

 If the CD-R/CD-RW has been recorded on a PC, it

needs to be finalized.

 Replace all the batteries with new ones when the

OPR/BATT indicator  dims.

“NO CD” appears when the disc is loaded.

 No disc is set in the CD compartment. Set a disc.

 The CD may have a reading problem. Replace the

disc.

 The CD may be placed upside down. Place the

disc with the label side up.

 An unplayable disc (DVD, BD, etc.) is loaded.

Replace the disc.

“NO TRACK” appears on the display when

the disc is loaded.

 No audio files recorded in supported formats, or a

file to be played back has an unsupported file

extension.

“DISC ERR” appears when the disc is loaded.

 The CD may be dirty. Clean the disc.

 The CD may have scratches. Replace the disc.

 The CD may have a reading problem. Replace the

disc.

 A blank disc may be set in the CD compartment.

The sound drops out.

 Reduce the volume.

 Clean the CD, or replace it if the CD is badly

damaged.

 Place the unit in a location free from vibrations.

 Clean the lens with a commercially available

blower.

 The sound may drop out or noise may be heard

when using a poor quality CD-R/CD-RW or if there

is a problem with the recording device or

application software.

Starting playback takes more time than

usual.

 The following discs take a longer time to start

playback.

 A disc recorded with a complicated tree

structure.

 A disc that has many folders or non-MP3/WMA

files.

USB device

The USB device does not work properly.

 If you connect an incompatible USB device, the

following problems may occur.

 The USB device is not recognized.

 File or folder names are not displayed on this

unit.

 Playback is not possible.

 The sound skips.

 There is noise.

 The sound output is distorted.

“NOT SUPPORT” appears.

 An unexpected error occurs in the connected

device.

 An unknown device is connected.

 An unsupported USB device is connected and

playback or pause operation is performed.

PTY (programme type)

This function indicates services in programme type, such as

News or Sports, transmitted in the DAB.

If the received service does not transmit the programme

type, “NO PTY” appears.

Programme type Display

No programme type NONE

News NEWS

Current Affairs AFFAIRS

Information INFO

Sport SPORT

Education EDUCATE

Drama DRAMA

Culture ARTS

Science SCIENCE

Varied TALK

Pop Music POP

Rock Music ROCK

Easy Listening Music EASY

Light Classical CLASSICS

Serious Classical CLASSICS

Other Music OTHER M

Weather WEATHER

Finance FINANCE

Children’s programmes CHILDREN

Social Affairs FACTUAL

Religion RELIGION

Phone In PHONE IN

Travel TRAVEL

Leisure LEISURE

Jazz Music JAZZ

Country Music COUNTRY

National Music NATION M

Oldies Music OLDIES

Folk Music FOLK

Documentary DOCUMENT

License and Trademark Notice

 MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and

Thomson.

 Windows Media is either a registered trademark

or trademark of Microsoft Corporation in the

United States and/or other countries.

 This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

 Other trademarks and trade names are those of

their respective owners. In this manual, ™ and ®

marks are not specified.

Downloaded from www.vandenborre.be

Produktspezifikationen

Marke:	Sony
Kategorie:	Radio
Modell:	ZS-PS55

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sony ZS-PS55 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Radio Sony

Sony XDR-P1BDPB Bedienungsanleitung

12 September 2024

Sony XDR-S41DB Bedienungsanleitung

10 September 2024

Sony CFM-A50 Bedienungsanleitung

13 August 2024

Sony XDR-S41DR Bedienungsanleitung

10 August 2024

Sony XDR-S41DW Bedienungsanleitung

3 August 2024

Sony ICF-CD853 Bedienungsanleitung

1 August 2024

Sony XDR-S61DB Bedienungsanleitung

1 August 2024

Sony SRF-M37 Bedienungsanleitung

30 Juli 2024

Sony XDR-S1 Radio Bedienungsanleitung

23 Juli 2024

Sony ICF-CD837L Bedienungsanleitung

20 Juli 2024

Bedienungsanleitung Radio

Neueste Bedienungsanleitung für -Kategorien-

Ruarkaudio Rseven Bedienungsanleitung

16 Oktober 2024

Ruarkaudio MR1 Bedienungsanleitung

16 Oktober 2024

Denver TWE-55B Bedienungsanleitung

15 Oktober 2024

AudioSonic CL-1486 Bedienungsanleitung

14 Oktober 2024

Sangean DPR-39 Bedienungsanleitung

14 Oktober 2024

Sangean RCR-9 Bedienungsanleitung

14 Oktober 2024

PerfectPro Dabbox Bedienungsanleitung

13 Oktober 2024

Uniden UH45CP Bedienungsanleitung

12 Oktober 2024

Sencor SIR 5000WDB Bedienungsanleitung

11 Oktober 2024

AEG KRC 4350 BT Bedienungsanleitung

10 Oktober 2024