Sony SA-D40 Bedienungsanleitung

Sony Heimkino-Set SA-D40

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony SA-D40 (2 Seiten) in der Kategorie Heimkino-Set. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing,

and do not place objects filled with liquids, such as vases, on the appliance.

To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers,

tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example,

lighted candles).

As the main plug is used to disconnect the unit from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from

the AC outlet immediately.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine

and fire.

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with

the installation instructions.

The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the

unit itself has been turned off.

For the customers in India

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union

and other European countries with separate collection systems)

For the customers in UAE

Unpacking

 Satellite speakers

SA-D20 (2)

SA-D40 (4)

 Foot pads

SA-D20 (8)

SA-D40 (16)

 Subwoofer (1)

 Stereo mini plug

cord (1)

 R03 (size AAA)

batteries (2)

 AC power adaptor

(1)

 Power cord (1)

 Remote commander

(remote) (1)

Attaching the foot pads to the satellite speakers

Attach the foot pads (supplied) to the bottom of the speakers to stabilize the speakers and

prevent them from slipping.

Remove the foot pads

from the protective cover.

e.g. SA-D40

Inserting the batteries into the remote

Insert two R03 (size AAA) batteries (supplied) by matching the and ends on the batteries to  

the marking inside the compartment. To use the remote, point it at the remote sensor on the

subwoofer.

Notes

 Do not leave the remote in an extremely hot or humid place.

 Do not use a new battery with an old one.

 Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

 Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a

malfunction.

 If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible

damage from battery leakage and corrosion.

Index to parts and controls

Subwoofer

Front panel

  

 



  / (on/standby) button

Turns on the system, or sets it to standby

mode.

 FUNCTION button

Selects an input source.

 Remote sensor

 FUNCTION indicators

 TV

 USB

 BLUETOOTH

Lights up in green when the function is

selected. (BLUETOOTH® function: lights up

or blinks in blue.) When the system turns

on, the indicator of the function that was

set last time lights up.

 USB PLAY buttons

  (play/pause)/USB PLAY indicator

  (rewind/skip back)

  (fast forward/skip forward)

 (USB) port

Remote commander (remote)











  / (on/standby)

Turns on the system, or sets it to standby

mode.

 FUNCTION

Selects an input source.

  (play/pause)

Starts/Pauses playback on a USB device.

  (rewind/skip back)/ (fast 

forward/skip forward), (folder) +/–

Selects files/folders on a USB device.

 VOLUME +/–

Adjusts the volume.

There is a tactile dot to the right of the

VOLUME + button. Use the tactile dot as a

reference when operating the remote.

Set Up

Step 1: Positioning the speaker system

Place all speakers and subwoofer anywhere you like to in the room. Wherever the speaker system

is placed, you will be able to achieve the best possible sound from them.

Satellite

speakers

Satellite

speakers

Subwoofer

* *

* Only for SA-D40

To install the satellite speakers on a wall

Prepare screws ( )* (not supplied) that are suitable for the hole on the back of each speaker ( ).

Then, fasten the screws to the wall ( ). You can hang the speakers on the screws.

* The screws ( ) needed are two for SA-D20 or four for SA-D40.



30 mm or longer

4 mm



5 mm

10 mm



6 to 7 mm



Caution

 Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or

improper screw installation, natural calamity, etc.

Step 2: Connecting the satellite speakers

Connect the satellite speaker cords to the satellite speaker terminals of the subwoofer.

The supplied satellite speakers are all the same and there is no difference between the left and

right.

The satellite speaker connected to “Rch” should be located on the right side of the subwoofer and

the satellite speaker connected to “Lch” on the left side of the subwoofer.

SA-D20

Place on the right of

the subwoofer

Bottom

Place on the left of

the subwoofer

Insert the plug

until it clicks

Subwoofer

Lch

Rch

SA-D40

Place on the right of

the subwoofer

Insert the plug

until it clicks

Place on the left of

the subwoofer

LchRch

Bottom

Subwoofer

Lch

Rch

Step 3: Connecting the system to your TV and the mains

Before connecting the system to the mains, connect it to your TV first.

AC power adaptor

(supplied) Power cord

(supplied)

Stereo mini plug cord

(supplied)

To headphone jack

To mains

1 Connect the system to your TV as in the illustration above.

2 Connect the power cord to the AC power adaptor. Then connect the AC

power adaptor to the system.

3 Connect the power cord to the mains.

The subwoofer enters standby mode.

Caution

 Do not use an AC power adaptor other than the one supplied with this system.

Step 4: Turning the system on

Subwoofer

 /

Remote

1 Press  / on the subwoofer or remote.

The subwoofer turns on.

Listening to input sources

Listening to a TV

You can listen to a TV connected to the system.

FUNCTION

VOLUME +/–

1 Press FUNCTION to select TV.

The TV indicator lights up in green.

2 Select the TV program on the TV.

3 Press VOLUME +/– to adjust the

volume.

Note

 If the volume is too low, adjust the volume using

the remote commander of the TV.

Listening to a USB device

By connecting a USB device (containing music files copied from your computer), you can play

music files through this system. This system will play back MP3 and WMA files. Make sure that the

system is turned off before you connect or disconnect a USB device.

USB indicator

USB PLAY indicator (USB) port

1 Connect the USB device to the (USB) port of the subwoofer.

2 Press FUNCTION repeatedly to select USB.

The USB indicator lights up in green.

3 Press .

Playback starts and the USB PLAY indicator lights up in green.

4 Press VOLUME +/– to adjust the volume.

FUNCTION



VOLUME +/–

 / , +/–

Other operations

To Press

Pause

playback

. To resume playback, press

the button again.

Select a

folder

+/– repeatedly.

Select a

file

 / repeatedly.

Find a

point in a

file

Hold down / during  

playback, and release the

button at the desired point.

Notes

 When USB cable connection is necessary, connect the USB cable supplied with the USB device to be connected.

See the operation manual supplied with the USB device to be connected for details on the operation method.

 Do not connect the system and the USB device through a USB hub.

 When the USB device is inserted, the system reads all the files on the USB device. If there are many folders or

files on the USB device, it may take a long time to finish reading the USB device.

 With some connected USB devices, after an operation is performed, there may be a delay before it is

performed by this system.

 Compatibility with all encoding/writing software cannot be guaranteed. If audio files on the USB device were

originally encoded with incompatible software, those files may produce noise or interrupted sound, or may not

be played back at all.

 This system cannot play audio files on the USB device in the following cases;

 when the total number of audio files in a folder exceeds 256.

 when the total number of folders on a USB device exceeds 256 (including the “ROOT” folder and empty

folders).

 The numbers of playable files/folders above may vary depending on the file and folder structure. Do not save

other types of files or unnecessary folders on a USB device that has audio files.

 The system can play back to a depth of eight folders only.

 This system does not necessarily support all the functions provided in a connected USB device.

 Folders that have no audio files are skipped.

 This system is designed for playback of the following audio formats.

 MP3: file extension “.mp3”

 WMA: file extension “.wma”

 Note that even when file name has the correct file extension, if the actual file differs, the system may produce

noise or may malfunction.

4-727-386- (1)12

Operating Instructions

Multimedia Speaker System

SA-D20/SA-D40

Using the BLUETOOTH

function

You can listen to music from your BLUETOOTH

mobile phone or BLUETOOTH device over a

wireless connection.

The system supports the BLUETOOTH A2DP

profiles. For details on BLUETOOTH wireless

technology, see “BLUETOOTH wireless

technology.”

About pairing

In order to use the BLUETOOTH function, it is

necessary to register devices in advance. This

registration is called “pairing.” Pairing is

necessary for a device to connect for the first

time. If you register a device once, you will not

need to pair with the same device again unless

you initialize the system. However, in the

following cases, you will have to perform

pairing again:

 Pairing information is deleted as a result of

repairing the system.

 The connection history with the system is deleted

on the connected device.

 All the connection history of the system is deleted.

Notes

 The system can be paired with up to eight devices.

If a further device is paired, the pairing information

of the device with the oldest connection date is

overwritten with new information.

 When deleting the pairing information of this

system or pairing again after returning from repair,

you may not be able to pair with the device you are

connecting to if the information on this system

remains (iPhone, etc.). In this case, delete the

registration information of this system from the

device to be connected and pair it again.

 To connect with a PC, the PC must have BLUETOOTH

wireless technology.

 The system does not support NFC communication.

Step 1: Pairing and

connecting the system with

a BLUETOOTH device

Place the system and the BLUETOOTH device

within 1 meter of each other.

1 Select the BLUETOOTH function

by pressing FUNCTION

repeatedly.

The BLUETOOTH indicator of the system

blinks and the system is ready for pairing.

FUNCTION

2 Set the BLUETOOTH device to

pairing mode.

For details on setting the BLUETOOTH

device to pairing mode, refer to the

operating instructions supplied with the

device.

3 Select “SA-D20” or “SA-D40” on

the BLUETOOTH device display.

The BLUETOOTH indicator of the system

blinks and the system starts to connect.

If a Passkey is requested, enter “0000.”

Perform these steps within five minutes,

otherwise pairing will be cancelled.

SA-D20

4 Once pairing is completed, the

device and the system are

connected automatically.

When the connection is established, the

system enters playback mode, the

BLUETOOTH indicator of the system lights

up, and the information of the paired

device is stored in the system.

BLUETOOTH indicator

About the indicator for

BLUETOOTH connection

The BLUETOOTH indicator on the front panel

lights up or blinks in blue to show the system

status.

System status Indicator

The system is pairing/waiting for

pairing. Blinks

The system is connecting with a

BLUETOOTH device.

The system has established

connection with a BLUETOOTH

device.

Lights up

The system is not in BLUETOOTH

mode.

Turns off

Tip

 When the BLUETOOTH indicator stops blinking and

turns off, perform the pairing operations from Step

1 again.

Notes

 The BLUETOOTH devices to be connected must

support A2DP (Advanced Audio Distribution Profile).

 For details on operation of the connected devices,

refer to the operating instructions supplied with the

devices.

 Use a BLUETOOTH device such as a BLUETOOTH

mobile phone in an easily visible place in the same

room where the subwoofer is placed.

 If Wi-Fi equipment is used, BLUETOOTH

communication may become unstable. In that case,

use the BLUETOOTH device as close as possible to

the subwoofer.

 Sound may be interrupted because of a problem

with the BLUETOOTH device.

 “Passkey” may be called “Passcode,” “PIN code,”

“PIN number” or “Password,” etc., depending on the

device.

 The pairing standby status of the system is

cancelled after about five minutes, and the

indicator on the front panel blinks. If pairing is not

successful, repeat the procedure from step 2.

Step 2: Listening to music

with the BLUETOOTH

connection

The system supports SCMS-T content

protection. You can listen to a BLUETOOTH

device that supports SCMS-T content

protection.

Before starting music playback operations,

check the following:

 The BLUETOOTH function on the BLUETOOTH device

is on.

 The pairing procedure is completed on both the

system and BLUETOOTH device.

1 Select the BLUETOOTH function

by pressing FUNCTION

repeatedly.

The BLUETOOTH indicator blinks.

2 Start the BLUETOOTH connection

from the BLUETOOTH device.

The BLUETOOTH indicator on the front

panel lights up when the BLUETOOTH

connection is established.

3 Start playback on the

BLUETOOTH device.

4 Adjust the volume.

Set the volume of the BLUETOOTH device

to a moderate level and press the VOLUME

+/– buttons on the remote to adjust the

volume of the system.

Note

 If the source device has a bass boost function or

equalizer function, turn them off. If these functions

are on, sound may be distorted.

 In the following cases, you will have to make the

BLUETOOTH connection again.

 The power of the system does not turn on.

 The power of the BLUETOOTH device does not

turn on, or the BLUETOOTH function is off.

 The BLUETOOTH connection is not established.

 If more than one device paired with the system is

being played back, sound will be heard from just

one of those devices.

Step 3: Finishing the

BLUETOOTH connection

Terminate the BLUETOOTH connection by any

of the operations listed below.

 Operate the BLUETOOTH device to terminate the

connection. For details, refer to the operating

instructions supplied with the device.

 Turn off the BLUETOOTH device.

 Turn off the system.

 Select any function except BLUETOOTH.

To delete all the pairing

information

When the BLUETOOTH function is selected,

press and hold on the subwoofer for over 

two seconds and press VOLUME– on the

remote. The pairing information will be

deleted and the system will turn off

automatically.

Troubleshooting

Should you encounter a problem with your

speaker system, check the following list and

take the indicated measures. If the problem

persists, consult your nearest Sony dealer.

Be sure to bring both your subwoofer and

satellite speakers, even if it seems as though

only one has a problem, when you request a

repair.

Sound

There is no sound from the speaker system.

 If the TV combines a headphone output as

audio output, make sure the audio output

setting of the TV is set for speaker. For

details, refer to the operating instructions

supplied with the TV.

 Check that the volume of the TV is not set

to small or the mute.

 Make sure all the connections have been

correctly made.

 Make sure the volume on the speaker

system has been turned up properly.

 Make sure the correct input source has

been selected.

 Make sure that the speaker system is not

in the standby mode.

There is distortion in the speaker output.

 Check if any sound-enhancing functions

on the connected device have been

activated. If they have, turn them off.

There is hum or noise in the speaker output.

 Make sure all the connections have been

correctly made.

 Make sure none of the audio components

are positioned too close to the TV set.

 If the volume level of the speaker system is

turned up to maximum, extraneous noise

may be output.

The sound has suddenly stopped.

 Make sure all the connections have been

correctly made. Contact between bare

speaker wires at the speaker terminals

may cause a short circuit.

 Disconnect the power cord, reconnect it,

and then turn on the system again by

pressing / . 

Bass sounds are produced too heavily.

 Some material is recorded with strong

emphasis on bass sounds, which may be

excessive in some cases.

No sound is output from specific speakers.

 Check that the speaker cords are fully

inserted into the terminals of the

subwoofer.

 Turn on the system again by pressing / . 

USB device

There is no sound from the USB device.

 The USB device is not connected correctly.

Disconnect the USB device from the

system, and then reconnect it.

There is noise, skipping, or distorted sound.

 Disconnect the USB device from the

system, and then reconnect it.

 The music data itself contains noise, or the

sound is distorted. Noise may have been

entered when creating music data due to

the conditions of the computer. Create the

music data again.

 The bit rate used when encoding the files

was low. Send files encoded with higher

bit rates to the USB device.

It takes a long time for playback to start.

 The reading process can take a long time

in the following cases.

 There are many folders or files on the

USB device.

 The file structure is extremely complex.

 The memory capacity is excessive.

 The internal memory is fragmented.

The USB device is not recognized.

 Disconnect the USB device from the

system, and then reconnect it.

 The USB PLAY indicator blinks twice if an

incompatible USB device is connected.

 The USB PLAY indicator blinks four times if

a USB device is connected through a USB

hub. Always connect a USB device directly

to the system.

 The USB device does not work properly.

Refer to the USB device operation manual

for how to deal with this problem.

Playback does not start.

 Disconnect the USB device from the

system, and then reconnect it.

 Press  to start playback.

Files cannot be played back.

 The audio file does not have the extension

“.mp3” or “.wma.”

 The data is not stored in MP3/WMA

format.

 USB storage devices formatted with file

systems other than FAT16 or FAT32 are

unsupported.*

 If you use a partitioned USB storage

device, only files on the first partition can

be played.

 Files that are encrypted or protected by

passwords, etc. cannot be played back.

* This system supports FAT16 and FAT32, but some USB

storage devices may not support all of these FAT. For

details, see the operation manual of each USB storage

device or contact the manufacturer.

BLUETOOTH

There is no sound from the BLUETOOTH

device

 Make sure the system is not too far from

the BLUETOOTH device, or the system is

not receiving interference from a Wi-Fi

network, other 2.4 GHz wireless device, or

microwave oven.

 Check that the BLUETOOTH connection is

made properly between the system and

the BLUETOOTH device.

 Pair the system and the BLUETOOTH device

again.

 Keep the system away from metal objects

or surfaces.

 Make sure the system is in BLUETOOTH

mode.

Sound skips or the transmission distance is

short.

 If a device that generates electromagnetic

radiation, such as a Wi-Fi network, other

BLUETOOTH device(s), or a microwave

oven is nearby, move away from such

sources.

 Remove any obstacle between the system

and BLUETOOTH device, or move away

from the obstacle.

 Locate the system and BLUETOOTH device

as close to each other as possible.

 Re-position the system.

 Re-position the BLUETOOTH device.

Connecting cannot be established.

 Perform pairing again.

Pairing cannot be completed.

 Bring the system and the BLUETOOTH

device closer together.

 Delete the information of the system from

your BLUETOOTH device and perform

pairing again.

Specifications

Satellite speakers

Speaker System

Full range, Bass reflex

Speaker units

80 mm cone type

Dimensions (approx.)

106 mm × 188 mm × 96 mm

(w/h/d)

Mass (approx.)

0.5 kg

Subwoofer

Speaker System

Active subwoofer, Bass reflex

Speaker unit

160 mm cone type

Dimensions (approx.)

250 mm × 337 mm × 400 mm

(w/h/d)

Mass (approx.)

4.5 kg

Inputs

Stereo mini jack × 1

(USB) port

Type A

Amplifier section

Satellite speakers

Power output (rated)

SA-D20: 8 W + 8 W

(at 5 + 5 ohms, 1 kHz, 1% THD)

SA-D40: 10 W + 10 W

(at 6 + 6 ohms, 1 kHz, 1% THD)

RMS output power (reference)

SA-D20: 15 W + 15 W

(at 5 + 5 ohms, 1 kHz, 10% THD)

SA-D40: 20 W + 20 W

(at 6 + 6 ohms, 1 kHz, 10% THD)

Subwoofer

RMS output power (reference)

SA-D20: 30 W (at 4 ohms, 70 Hz, 10% THD)

SA-D40: 40 W (at 4 ohms, 70 Hz, 10% THD)

USB section

Maximum current

500 mA

BLUETOOTH section

Communication system

BLUETOOTH Specification version

2.1 + EDR

Output

BLUETOOTH Specification Power

Class 2

Maximum communication range

Line of sight approx. 10 m*1

Frequency band

2.4 GHz band (2.4000 GHz - 2.4835

GHz)

Modulation method

FHSS (Freq Hopping Spread

Spectrum)

Compatible BLUETOOTH profiles*2

A2DP (Advanced Audio Distribution

Profile)

Supported Codecs*3

SBC*4

Transmission range (A2DP)

20 Hz - 20,000 Hz (Sampling

frequency 44.1 kHz)

*1 The actual range will vary depending on

factors such as obstacles between devices,

magnetic fields around a microwave oven,

static electricity, cordless phone, reception

sensitivity, operating system, software

application, etc.

*2 BLUETOOTH standard profiles indicate the

purpose of BLUETOOTH communication

between devices.

*3 Codec: Audio signal compression and

conversion format

*4 Subband Codec

General

Power requirements

SA-D20: DC 18 V 0.8 A

SA-D40: DC 18 V 1.0 A

(supplied AC power adaptor)

AC power adaptor

Input: 100 V – 240 V AC, 50/60 Hz

Output: DC 18 V 2.6 A

Power consumption

SA-D20: 15 W

SA-D40: 18 W

Design and specifications are subject to

change without notice.

BLUETOOTH wireless

technology

BLUETOOTH wireless technology is a short-

range wireless technology linking digital

devices, such as personal computers and

digital cameras. Using the BLUETOOTH wireless

technology, you can operate the units involved

within a range of about 10 meters.

The BLUETOOTH wireless technology is

commonly used between two devices, but a

single device can be connected to multiple

devices.

You do not need wires to get connected as you

do with a USB connection, and you do not

need to place the devices face to face as you

do with wireless infrared technology.

You can use the technology with one

BLUETOOTH device in your bag or pocket.

BLUETOOTH wireless technology is a global

standard supported by thousands of

companies. These companies produce

products that meet the global standard.

Supported BLUETOOTH

version and profiles

Profile refers to a standard set of capabilities

for various BLUETOOTH product capabilities.

The system supports the following

BLUETOOTH version and profiles.

Supported BLUETOOTH version:

BLUETOOTH Standard version 2.1 + EDR

(Enhanced Data Rate)

Supported BLUETOOTH profiles:

A2DP (Advanced Audio Distribution Profile)

Notes

 For you to use the BLUETOOTH function, the

BLUETOOTH device to be connected must support

the same profile as the system. Even if the device

supports the same profile, the functions may differ

because of the specifications of the BLUETOOTH

device.

 The audio playback on the system may be delayed

from that on the BLUETOOTH device because of the

characteristics of the BLUETOOTH wireless

technology.

Effective communication

range

BLUETOOTH devices should be used within

approximately 10 meters (unobstructed

distance) of each other. The effective

communication range may become shorter

under the following conditions.

 When a person, metal object, wall or other

obstruction is between the devices with a

BLUETOOTH connection

 Locations where a wireless LAN is installed

 Around microwave ovens that are in use

 Locations where other electromagnetic waves occur

Effects of other devices

BLUETOOTH devices and wireless LAN (IEEE

802.11b/g) use the same frequency band (2.4

GHz). When using your BLUETOOTH device

near a device with wireless LAN capability,

electromagnetic interference may occur. This

could result in lower data transfer rates, noise,

or inability to connect. If this happens, try the

following remedies:

 Try connecting the system and BLUETOOTH mobile

phone or BLUETOOTH device when you are at least

10 meters away from the wireless LAN equipment.

 Turn off the power to the wireless LAN equipment

when using your BLUETOOTH device within 10

meters.

Effects on other devices

The radio waves broadcast by the system may

interfere with the operation of some medical

devices. Since this interference may result in

malfunction, always turn off the power on the

system, BLUETOOTH mobile phone and

BLUETOOTH device in the following locations:

 In hospitals, on trains, in airplanes, at gas stations,

and any place where flammable gasses may be

present

 Near automatic doors or fire alarms

Notes

 The system supports security functions that comply

with the BLUETOOTH specification as a means of

ensuring security during communication using

BLUETOOTH technology. However, this security may

be insufficient depending on the setting contents

and other factors, so always be careful when

performing communication using BLUETOOTH

technology.

 Sony cannot be held liable in any way for damages

or other loss resulting from information leaks

during communication using BLUETOOTH

technology.

 BLUETOOTH communication is not necessarily

guaranteed with all BLUETOOTH devices that have

the same profile as the system.

 BLUETOOTH devices connected with the system

must comply with the BLUETOOTH specification

prescribed by the BLUETOOTH SIG, Inc., and must

be certified to comply. However, even when a

device complies with the BLUETOOTH specification,

there may be cases where the characteristics or

specifications of the BLUETOOTH device make it

impossible to connect, or may result in different

control methods, display or operation.

 Noise may occur or the audio may cut off

depending on the BLUETOOTH device connected

with the system, the communications environment,

or surrounding conditions.

Precautions

On safety

 Completely disconnect the power cord (mains lead)

from the wall outlet (mains) if it is not going to be

used for an extended period of time. When

unplugging the system, always grip the plug. Never

pull the cord itself.

 Should any solid object or liquid get into the

system, unplug the system, and have it checked by

qualified personnel before operating it again.

 The AC power cord can be changed only by a

qualified service facility.

On operation

 Do not drive the speaker system with a continuous

wattage exceeding the maximum input power of

the system.

 If the polarity of the speaker connections is not

correct, the bass tones will be weak and the

position of the various instruments obscure.

 Before connecting, turn off the amplifier

(subwoofer) to avoid damaging the speaker system.

 The speaker grille cannot be removed. Do not

attempt to remove the grille on the speaker system.

If you try to remove it, you may damage the

speaker.

 The volume level should not be turned up to the

point of distortion.

On placement

 Do not set the speaker system in an inclined

position.

 Do not place the speaker system in locations that

are:

 Extremely hot or cold

 Dusty or dirty

 Very humid

 Subject to vibrations

 Subject to direct sunlight

 Use caution when placing the speaker system on a

specially treated (waxed, oiled, polished, etc.) floor,

as staining or discoloration may result.

 If you install the system with its back against a wall,

position it at least 10 cm away from the wall so as

not to block the ventilation slots and prevent heat

release.

On cleaning

Clean the speaker system cabinets with a soft cloth

lightly moistened with a mild detergent solution or

water. Do not use any type of abrasive pad, scouring

powder, or solvent such as alcohol or benzine.

On your TV’s color

If the speakers should cause your TV screen to have

color irregularity, turn off the TV then turn it on after

15 to 30 minutes. If color irregularity should persist,

place the speaker system further away from your TV

set.

License and Trademark

Notice

 MPEG Layer-3 audio coding technology and patents

licensed from Fraunhofer IIS and Thomson.

 Windows Media is either a registered trademark or

trademark of Microsoft Corporation in the United

States and/or other countries.

 This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

 The BLUETOOTH® word mark and logos are

registered trademarks owned by Bluetooth SIG, Inc.

and any use of such marks by Sony Corporation is

under license. Other trademarks and trade names

are those of their respective owners.

Produktspezifikationen

Marke:	Sony
Kategorie:	Heimkino-Set
Modell:	SA-D40

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sony SA-D40 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Heimkino-Set Sony

Sony SA-PSD5 Bedienungsanleitung

14 Oktober 2024

Sony HTSD35 Bedienungsanleitung

2 September 2024

Sony SHAKE-X30D Bedienungsanleitung

30 August 2024

Sony DAV-DZ840K Bedienungsanleitung

26 August 2024

Sony HT-DDW885 Bedienungsanleitung

24 August 2024

Sony DAV-DZ720 Bedienungsanleitung

13 August 2024

Sony DAV-HDZ284 Bedienungsanleitung

31 Juli 2024

Sony WS-FL7 Bedienungsanleitung

26 Juli 2024

Sony DAV-DZ940K Bedienungsanleitung

22 Juli 2024

Sony DAV-JZ8888K Bedienungsanleitung

21 Juli 2024

Bedienungsanleitung Heimkino-Set

Neueste Bedienungsanleitung für -Kategorien-

Onkyo HT-S9800 Bedienungsanleitung

13 Oktober 2024

LG MAI0702 Bedienungsanleitung

8 Oktober 2024

LG LH-TK3605Q Bedienungsanleitung

8 Oktober 2024

Hyundai H-HT5111 Bedienungsanleitung

5 Oktober 2024

Bose Wave Music System II Acoustic Bedienungsanleitung

27 September 2024

Teufel Impaq 300 Blu-ray System Bedienungsanleitung

24 September 2024

Akai AHC1500 Bedienungsanleitung

23 September 2024

Klipsch Quintet 5 Bedienungsanleitung

21 September 2024

LG HT865PH Bedienungsanleitung

13 September 2024

Onkyo HT-S7700 Bedienungsanleitung

8 September 2024