Sony CMT-V11iP Bedienungsanleitung

Sony Hi-Fi-Anlage CMT-V11iP

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony CMT-V11iP (2 Seiten) in der Kategorie Hi-Fi-Anlage. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

WARNING

To reduce the risk of fire, do not cover the ventilation

opening of the apparatus with newspapers, tablecloths,

curtains, etc. Do not place the naked flame sources such

as lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do not expose

this apparatus to dripping or splashing, and do not place

objects filled with liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space, such as a

bookcase or built-in cabinet.

As the main plug of AC adaptor is used to disconnect

the AC adaptor from the mains, connect it to an easily

accessible AC outlet. Should you notice an abnormality

in it, disconnect it from the AC outlet immediately.

Do not expose batteries or apparatus with battery-

installed to excessive heat such as sunshine, fire or the

like.

The AC adaptor is not disconnected from the mains as

long as it is connected to the AC outlet, even if the main

unit itself has been turned off.

The nameplate is located on the bottom exterior of the

main unit and on the surface of the AC adaptor.

CAUTION

The use of optical instruments with this product will

increase eye hazard.

This appliance is classified

as a CLASS 1 LASER

product. This marking

is located on the bottom

exterior of the main unit.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying EU

directives.

This product has been manufactured by or on behalf

of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. Inquiries related to product compliance

based on European Union legislation shall be addressed

to the authorized representative, Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,

Germany. For any service or guarantee matters, please

refer to the addresses provided in the separate service or

guarantee documents.

For customers in Europe and Australia

Disposal of Old Electrical &

Electronic Equipment

(Applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the product or on its packaging indicates

that this product shall not be treated as household

waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and

electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by inappropriate

waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed

information about recycling of this product, please

contact your local Civic Office, your household waste

disposal service or the shop where you purchased the

product.

Applicable accessory: Remote commander

Europe Only

Disposal of waste batteries

(applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the battery or on the packaging indicates

that the battery provided with this product shall not be

treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The chemical

symbols for mercury (Hg) or lead (Pb) are added if the

battery contains more than 0.0005% mercury or 0.004%

lead.

By ensuring these batteries are disposed of correctly,

you will help prevent potentially negative consequences

for the environment and human health which could

otherwise be caused by inappropriate waste handling of

the battery. The recycling of the materials will help to

conserve natural resources.

In case of products that for safety, performance or data

integrity reasons require a permanent connection with an

incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will

be treated properly, hand over the product at end-of-life

to the applicable collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on how

to remove the battery from the product safely. Hand the

battery over to the applicable collection point for the

recycling of waste batteries.

For more detailed information about recycling of this

product or battery, please contact your local Civic Office,

your household waste disposal service or the shop where

you purchased the product.

Note on DualDiscs

A DualDisc is a two sided disc product which mates

DVD recorded material on one side with digital

audio material on the other side. However, since the

audio material side does not conform to the Compact

Disc (CD) standard, playback on this product is not

guaranteed.

Music discs encoded with copyright

protection technologies

This product is designed to playback discs that conform

to the Compact Disc (CD) standard. Recently, various

music discs encoded with copyright protection

technologies are marketed by some record companies.

Please be aware that among those discs, there are some

that do not conform to the CD standard and may not be

playable by this product.

License and Trademark Notice

iPhone, iPod, iPod classic, iPod nano, and iPod touch

are trademarks of Apple Inc., registered in the U.S. and

other countries.

MPEG Layer-3 audio coding technology and patents

licensed from Fraunhofer IIS and Thomson.

Windows Media is either a registered trademark or

trademark of Microsoft Corporation in the United

States and/or other countries.

This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this product

is prohibited without a license from Microsoft or an

authorized Microsoft subsidiary.

All other trademarks and registered trademarks are of

their respective holders. In this manual, ™ and ® marks

are not specified.



Getting Started

Location of Controls

Connecting the iPod/iPhone

Connect an iPod/iPhone to the (USB) port  using a

USB cable supplied with your iPod/iPhone.

Setting the clock

1 Press   to turn on the system.

2 Press TIMER MENU  to select the clock set mode.

If “PLAY SET” flashes, press /    repeatedly to

select “CLOCK,” and then press (enter) .

3 Press  / repeatedly to set the hour, then press

(enter) .

4 Use the same procedure to set the minutes.

Note

The clock settings are reset when you disconnect the power cord or if

a power failure occurs.

To display the clock when the system is off

Press DISPLAY . The clock is displayed for about

8 seconds.

Operations

Playing a CD/MP3 disc

1 Select the CD function.

Press CD FUNCTION  on the remote or press

FUNCTION  on the unit repeatedly.

2 Open the CD door.

Press  (Open/Close)  on the unit.

  (Open/Close)

3 Set a disc.

Push the center part of the disc with two fingers until

the disc snaps into its mounted position.

Set a disc with the

label side facing

forward.

4 Close the CD door.

Press  (Open/Close)  on the unit.

“READING” appears.

5 Start playback.

Press   on the remote or press   on the

unit.

To eject a disc

Press  (Open/Close)  on the unit and remove the

disc by pulling up the edge of the disc while holding one

finger against the spindle.

Notes

The system will automatically close the CD door if a few minutes 

elapse of no operation with the CD door open.

Do not set a disc with non-standard shapes (e.g., heart, square, star).

The disc may fall into the system and cause irreparable damage.

If you press /   with the CD door open, the system will

automatically close the CD door.

Do not use a disc with tape, seals or paste on it as this may cause a

malfunction.

When you eject a disc, handle the disc by its edge. Do not touch the

surface.

Other operations

To Press

Pause playback  (or  on the unit). To

resume play, press the button again.

Stop playback  .

Select a folder on

an MP3 disc +/ .

Select a track or

file

 / //   .

Find a point in a

track or file

Hold down /    (or

 /  on the unit) during

playback, and release the button at

the desired point.

Select Repeat Play REPEAT  repeatedly until “ ” or

“ 1” appears.

Eject a disc 

 on the unit.

To change the play mode

Press PLAY MODE  repeatedly while the player is

stopped. You can select Normal Play mode (“Normal”

or “FLDR” for all MP3 files in the folder on the disc),

Shuffle Play mode (“SHUF” or “FLDR SHUF*” for folder

shuffle), or Program Play mode (“PGM”).

* When playing a CD-DA (audio) disc, FLDR (SHUF) Play performs

the same operation as normal (SHUF) Play.

Notes on Shuffle Play mode

When Shuffle Play mode is set to “SHUF,” the system shuffle-plays

all tracks or files on the disc. When Shuffle Play mode is set to

“FLDR SHUF,” the system shuffle-plays all tracks or files in selected

folder.

When you turn off the system, the selected Shuffle Play mode

(“SHUF” or “FLDR SHUF”) is cleared and the play mode returns to

Normal Play mode (“FLDR”).

Notes on Repeat Play

“ ” indicates that all tracks or files will be repeated until you stop

playback.

“ 1” indicates that a single track or file will be repeated until you

stop playback.

Notes on playing MP3 discs

Do not save other types of tracks or files, or unnecessary folders on a

disc that has MP3 files.

Folders that have no MP3 files are skipped.

The system can only play MP3 files that have a file extension of

“.mp3.”

Even if a file name has the “.mp3” file extension, if the actual file

differs, playing it may generate loud noise that might even damage

the system.

The maximum number of:

 folders is 255* (including the root folder).

 MP3 files is 512.

 MP3 files in a single folder is 512.

 folder levels (in the tree structure of files) is 9.



 Power (DC IN 9.5 V)

1 Connect the AC adaptor to the unit.

2 Plug the AC adaptor into a wall outlet.

 AUDIO IN jack

Connect an external audio component.

Compatibility with all MP3 encoding/writing software, recording

device, and recording media cannot be guaranteed. Incompatible

MP3 discs may produce noise or interrupted audio or may not play

at all.

* This include folders that have no MP3 or other files. The number

of folders that the system can recognize may be less than actual

number of folders, depending on the folder structure.

Creating your own program

(Program Play)

1 Select the CD function.

Press CD FUNCTION  on the remote or press

FUNCTION  on the unit repeatedly.

2 Select the play mode.

Press PLAY MODE  repeatedly until “PGM”

appears while the player is stopped.

3 Select a folder (MP3 disc only).

Press +/  repeatedly to select the desired

folder.

4 Select the desired track or file.

Press /    repeatedly until the desired track

or file number appears.

Selected track or file

number

Total playing time

Total playing time for all the programmed tracks or

files, including the selected track or file, is displayed at

right on the panel.

5 Program the selected track or file.

Press  to enter the selected track or file.

“--.--” appears when the total playing time reaches 100

minutes for a CD or when you program MP3 files.

6 Repeat steps 3 through 5 to program additional

tracks or files, up to a total of 25 tracks or files.

7 To play your program of tracks or files, press 

(or on the unit). 

The program remains available until you remove the

disc from the disc compartment or unplug the 

power cord.

To play the same program again, press  (or 

 on the unit).

To cancel Program Play

Press PLAY MODE  repeatedly until “PGM”

disappears while the player is stopped.

To delete the last track or file of the program

Press CLEAR  while the player is stopped.

Listening to the radio

1 Select the TUNER function.

Press TUNER FM/AM FUNCTION  on the remote

repeatedly or press FUNCTION  on the unit

repeatedly.

2 Perform tuning.

For automatic scanning

Press TUNING MODE  repeatedly until “AUTO”

appears, and then press +/ . Scanning stops

automatically when a station is tuned in, and

“TUNED” and “STEREO” (for stereo programs only)

light up in the display.

If “TUNED” does not light up and the scanning does

not stop, press  to stop scanning, then perform

manual tuning (below).

When you tune in a station that provides RDS

services (European model only), information such

as the service name or station name is provided by

broadcasts.

For manual tuning

Press TUNING MODE  repeatedly until

“MANUAL” appears, and then press +/ 

repeatedly to tune in the desired station.

Tip

To reduce static noise on a weak FM stereo station, press FM MODE



repeatedly until “MONO” appears to turn off stereo reception.

Presetting radio stations

1 Tune in the desired station.

2 Press TUNER MEMORY  to select the tuner

memory mode.

Preset number

3 Press +/  or / / /  repeatedly to select

the desired preset number.

If another station is already assigned to the selected

preset number, the station is replaced by the new

station.

4 Press  to register the station.

5 Repeat steps 1 through 4 to register other stations.

You can preset up to 20 FM and 10 AM stations.



 To AC Adaptor

 AM loop antenna

 FM lead antenna (Extend it horizontally.)

Unit (Top)

 Display panel

When the system is powered up, the setting status appears on the display panel.

When the system goes to Standby mode, the setting status disappears from the display panel.

Unit (Front)

Remote sensor

CD door

(CD compartment)

Remote indicator

 Remote indicator

Lights in amber when a signal is received from the remote.

Remote

This manual mainly explains operations using the

remote, but the same operations can also be performed

using the buttons on the unit having the same or similar

names.

To use the remote

Remove the battery compartment lid, and insert the two

supplied R6 (size AA) batteries, side first, matching 

the polarities shown below.

Notes on using the remote

With normal use, the batteries should last for about 6 months.

Do not mix an old battery with a new one or mix different types of

batteries.

If you do not use the remote for a long period of time, remove the

batteries to avoid damage from battery leakage and corrosion.

 /  and (enter)  on the main unit and/or on the supplied

remote control will only work with the Apple devices (iPhone/iPod

touch) installed up to iOS 6.

It will not work with iOS 7 or later. In such case, please operate on

the screen of Apple devices directly.



 Antennas

Find a location and an orientation that provide good

reception, and then set up the AM antenna.

Keep the antenna away from the power cord to avoid

picking up noise.

To tune in to a preset radio station

If you registered a radio station to a preset number 1

to 6, the radio station will be tuned in by just pressing

the TUNER MEMORY NUMBER (1 to 6) when the 

system function is set to FM or AM.

If you registered a radio station to a preset number 7

or higher, press TUNING MODE repeatedly until 

“PRESET” appears then press +/ repeatedly to  

select the desired preset number.

Playing a file of the USB device

The audio format that can be played back on this system

is MP3/WMA*.

* Files with DRM (Digital Rights Management) copyright protection

or files downloaded from an online music store cannot be played

on this system. If you try to play one of these files, the system plays

the next unprotected audio file.

Check the websites below for the information about

compatible USB devices.

For customers in Europe:

<http://support.sony-europe.com/>

For customers in Latin America:

<http://www.sony-latin.com/index.crp>

For customers in Asia and other countries/regions:

<http://www.sony-asia.com/support>

1 Select the USB function.

Press USB FUNCTION  on the remote or press

FUNCTION  on the unit repeatedly.

2 Connect the USB device to the (USB) port .

3 Start playback.

Press  on the remote or press  on the

unit.

Other operations

To Press

Pause playback  (or  on the unit). To

resume play, press the button again.

Stop playback  . To resume play, press *

(or  on the unit). To cancel

resume play, press  again.

Select a folder +/  repeatedly.

Select a file  / //   .

Find a point in

a file

Hold down /    or /  

 (or /    on the unit)

during playback, and release the

button at the desired point.

Select Repeat Play REPEAT  repeatedly until “ ” or

“ 1” appears.

* When playing a VBR MP3/WMA file, the system may resume

playback from a different point.

To change the play mode

Press PLAY MODE  repeatedly while the player is

stopped. You can select Normal Play mode (playback

in sequence of all files on the USB device), Folder

Play mode (“FLDR” for all files in the specified folder

on the USB device), Shuffle Play mode (“SHUF” or

“FLDR SHUF” for folder shuffle), or Program Play mode

(“PGM”).

Notes on Shuffle Play mode

When Shuffle Play mode is set to “SHUF,” the system shuffle-plays

all audio files on the USB device. When Shuffle Play mode is set to

“FLDR SHUF,” the system shuffle-plays all audio files in selected

folder.

When you turn off the system, the selected Shuffle Play mode

(“SHUF” or “FLDR SHUF”) is cleared and the play mode returns to

Normal Play mode (“FLDR”).

Notes on Repeat play

If you select “ ” when the system is in Normal Play mode, the

system executes repeat play of all audio files in the USB device until

you stop playback. If you select “ ” when the system is in Folder

Play mode, the system executes repeat play of all audio files in the

selected folder until you stop playback.

If you select “ 1,” the system executes continuous repeat play of

the selected file until you stop playback.

Notes

The playback order for the system may differ from the playback

order of the connected digital music player.

Be sure to turn off the system before removing the USB device.

Removing the USB device while the system is turned on may corrupt

the data on the USB device.

When USB cable connection is necessary, connect the USB cable

supplied with the USB device to be connected. See the operation

manual supplied with the USB device to be connected for details on

the operation method.

It may take time before “READING” appears, depending on the type

of USB device connected.

The system does not support a USB hub. Do not connect the USB

device through a USB hub.

When the USB device is inserted, the system reads all the files on the

USB device. If there are many folders or files on the USB device, it

may take a long time to finish reading the USB device.

With some connected USB devices, after an operation is performed,

there may be a delay before it is performed by this system.

Compatibility with all encoding/writing software cannot be

guaranteed. If audio files on the USB device were originally encoded

with incompatible software, those files may produce noise or

interrupted sound, or may not be played back at all.

This system cannot play audio files on the USB device in the

following cases:

 when the total number of audio files in a folder exceeds 999

 when the total number of audio files on a USB device exceeds

3000

 when the total number of folders on a USB device exceeds 1000

(including the “ROOT” folder and empty folders)

These numbers may vary depending on the file and folder structure.

Do not save other types of files or unnecessary folders on a USB

device that has audio files.

The system can play back to a depth of 9 folders only (including the

“ROOT” folder).

This system does not necessarily support all the functions provided

in a connected USB device.

Folders that have no audio files are skipped.



4-462-381- (2)11

Personal Audio System

GB Operating Instructions

CMT-V11iP

If the sound source is set to an FM/AM station for a

timer, the system automatically turns on 15 seconds

before the preset time. If the sound source is set

to CD/USB, the system automatically turns on

30 seconds before the preset time.

To check the setting

1 Press TIMER MENU .

2 Press  / repeatedly to select “SELECT,” and then

press .

3 Press  / repeatedly to select “PLAY SEL,” and

then press .

To cancel the timer

Repeat the same procedure as above until “OFF” appears

in step 3, and then press .

To change the setting

Start over from step 1.

Notes

If you select a USB device as a timer and have many files or folders

on that device, it takes time for read processing, causing a slight

delay before start of play in response to the timer.

If the sound source for a Play Timer is set to an FM/AM station

tuned in using auto scanning or manual scanning, when you change

the radio station after setting the Play Timer, radio station tuning for

the Play Timer will also changed.

If the sound source for a Play Timer is set to an FM/AM station

with a registered preset number, the radio station tuning for the Play

Timer is fixed at what you set for it. Even if you change the radio

station after setting the Play Timer, the radio station setting for the

Play Timer will not change.

Notes for the iPod/iPhone user

Make sure the iPod/iPhone is not playing when using the Play

Timer.

The Play Timer may not be activated depending on the status of the

connected iPod/iPhone.

Tip

The Play Timer setting remains in effect as long as the setting is not

canceled manually and clock setting is completed.

Troubleshooting

1 Make sure the power cord is firmly connected.

2 Find your problem in the checklist below, and take

the indicated corrective action.

If the issue persists, contact your nearest Sony dealer.

General

The system does not turn on.

Is the power cord plugged in correctly?

The system has entered Standby mode

unexpectedly.

This is not a malfunction. The system enters Standby

mode automatically in about 30 minutes when there is

no operation or audio signal output. See “To turn off

the Automatic Standby function.”

The clock setting or the Play Timer operation

has been cancelled unexpectedly.

If about a minute elapses with no operation, the clock

setting or Play Timer setting is cancelled automatically.

Perform the operation again from the beginning.

There is no sound.

Press VOLUME + to turn up the volume.

Make sure additional audio components are connected

correctly.

Make sure the function is set to AUDIO IN.

Is anything blocking the ventilation holes of the system?

The specified station may have temporarily stopped

broadcast.

Severe hum or noise.

Move the system away from sources of noise.

Connect the system to a different wall outlet.

Install a noise filter (not supplied) to the power cord.

The remote does not function.

Remove any obstacles between the remote and the

remote sensor  on the unit, and position the unit

away from fluorescent lights.

Point the remote at the system’s sensor .

Move the remote closer to the system.

CD/MP3 disc

The sound skips, or the disc will not play.

Wipe the disc clean, and replace it.

Move the system to a location away from vibration (for

example, on top of a stable stand).

Play does not start from the first track.

Return to normal play by pressing PLAY MODE 

repeatedly until both “PGM” and “SHUF” disappear.

Starting playback takes more time than usual.

The following discs can increase the time it takes to

start playback:

 a disc recorded with a complicated tree structure

 a disc that has many folders

Erroneous display.

The data stored in the CD-DA, MP3 disc may have

been corrupted. Perform the transfer again.

The character codes that can be displayed by this

system are as follows:

 Uppercase (A to Z)

 Lowercase (a to z) (lowercase will be displayed as

uppercase)

 Digits (0 to 9)

 Symbols (˝ $ % ’ ( ) * + , – . / < = > ? @ [ \ ] `)

Other characters appear as “_”



USB device

Are you using a supported USB device?

If you connect an unsupported USB device, the

following problems may occur. Check the information

on the websites about compatible USB devices with

URLs listed under “Playing a file of the USB device.”

 The USB device is not recognized

 File or folder names are not displayed on this system

 Playback is not possible

 The sound skips

 There is noise

 A distorted sound is output

There is no sound.

The USB device is not connected correctly. Turn off the

system and reconnect the USB device.

There is noise, skipping, or distorted sound.

You are using an unsupported USB device. Check the

information on the websites about compatible USB

devices.

Turn off the system and reconnect the USB device, then

turn on the system.

The music data itself contains noise, or the sound

is distorted. Noise may have entered during the

transferring process. Delete the file, and try transferring

again.

The bit rate used when encoding audio files was low.

Send audio files with higher bit rate to the USB device.

“READING” is displayed for an extended time,

or it takes a long time before playback starts.

The reading process can take a long time in the

following cases:

 There are many folders or files on the USB device

 The file structure is extremely complex

 The memory capacity is excessive

 The internal memory is fragmented

Erroneous display.

The data stored in the USB device may have been

corrupted. Perform the transfer again.

The character codes that can be displayed by this

system are as follows:

 Uppercase (A to Z)

 Lowercase (a to z) (lowercase will be displayed as

uppercase)

 Digits (0 to 9)

 Symbols (˝ $ % ’ ( ) * + , – . / < = > ? @ [ \ ] `)

Other characters appear as “_”

The USB device is not recognized.

Turn off the system and reconnect the USB device, then

turn on the system.

Check the information on the websites about

compatible USB devices.

The USB device does not work properly. Refer to the

operating instructions supplied with the USB device for

how to deal with this problem.

Playback does not start.

Turn off the system and reconnect the USB device, then

turn on the system.

Check the information on the websites about

compatible USB devices.

Playback does not start from the first file.

Set the play mode to Normal Play mode.

Audio file cannot be played back.

MP3 files in MP3 PRO format cannot be played back.

WMA files in Windows Media Audio Lossless and

Professional format cannot be played back.

USB device formatted with file systems other than

FAT16 or FAT32 are unsupported.*

In case multiple partitions exist in USB device that is

being used, files may not be played back.

The system can play back to a depth of 9 folders only.

Files that are encrypted or protected by passwords, etc.

cannot be played back.

Files with copyright protection (Digital Rights

Management) cannot be played back by this system.

* This system supports FAT16 and FAT32, but some USB device

may not support all of these FAT. For details, refer to the operating

instructions of each USB device or contact the manufacturer.

iPod/iPhone

There is no sound.

Make sure the iPod/iPhone is connected securely.

Make sure the iPod/iPhone is playing music.

Make sure the iPod/iPhone is updated with the latest

software. If not, update the iPod/iPhone before using

with the system.

Adjust the volume.

The sound is distorted.

Make sure the iPod/iPhone is connected securely.

Turn down the volume.

Set the “EQ” setting of the iPod/iPhone to “Off ” or

“Flat.”

The iPod/iPhone does not function.

Shut down any other iOS applications running on the

iPod/iPhone. For details, refer to the operation manual

supplied with the iPod/iPhone.

Make sure the iPod/iPhone is connected securely.

Make sure the iPod/iPhone is updated with the latest

software. If not, update the iPod/iPhone before using

with the system.

Because the operation of the system and the iPod/

iPhone are different, you may not operate the iPod/

iPhone using buttons on the remote or unit. In this

case, use the control buttons on the iPod/iPhone.

The iPod/iPhone cannot be charged.

Make sure the iPod/iPhone is connected securely.

Make sure the system is turned on.



If you cannot fully charge the iPod/iPhone, charge it

again after turning the Automatic Standby function off.

Tuner

Severe hum or noise, or stations cannot be

received. (“TUNED” or “STEREO” flashes on the

display.)

Connect the antenna properly.

Find a location and an orientation that provide good

reception, and then set up the antenna again.

Keep the antennas away from the power cord to avoid

picking up noise.

Turn off nearby electrical equipment.

Several radio stations can be heard at the same

time.

Find a location and an orientation that provide good

reception, and then set up the antenna again.

Bundle the antenna cables using commercially available

cord clips, for example, and adjust the cable lengths.

To reset the system to factory settings

If the system still does not operate properly, reset the

system to factory settings.

Use buttons on the unit to reset the system to its factory

default settings.

1 Disconnect and reconnect the power cord, and then

turn on the system.

2 Press and hold  and /    on the unit until

“RESET” appears in the display.

All user-configured settings, such as preset radio

stations, timer, and the clock, are deleted.

To turn off the Automatic Standby function

This system is equipped with an Automatic Standby

function. With this function, the system enters Standby

mode automatically in about 30 minutes when there is no

operation or audio signal output.

By default, the Automatic Standby function is turned on.

Use buttons on the unit to turn off the Automatic

Standby function.

Hold down   while the system is on, until

“AUTO. STBY OFF” appears.

To turn on the function, repeat the procedure until

“AUTO. STBY ON” appears.

Notes

“AUTO. STBY” appears in the display for 2 minutes before the

system enters Standby mode.

The Automatic Standby function is invalid for the tuner function

(FM/AM), even when you have enabled it.

The system may not enter Standby mode automatically in the

following cases:

 while an audio signal is being detected

 during playback of audio tracks or files

 while the preset Sleep Timer or Play Timer is in process

The system counts down the time again until it enters Standby

mode, even when Automatic Standby function is enabled in the

following cases:

 when the USB device or iPod/iPhone is connected

 when a button on the remote or unit is pressed

 when a preset time of the Sleep or Play Timer is started

Messages

COMPLETE: The preset operation ended normally.

CONNECT: The connected iPod/iPhone is executing

authentication.

DEVICE ERROR: Unpredictable situation (or an

unknown device is connected).

FULL: You tried to program more than 25 tracks or files

(steps).

NO DEVICE: Neither a USB device nor an iPod/iPhone is

connected.

NO DISC: There is no disc in the player, or you have

loaded a disc that cannot be played.

NO STEP: All of the programmed tracks have been

erased.

NO SUPPORT: An unsupported USB device is

connected.

NO TRACK: There are no playable files in the USB device

or on the CD disc.

NOT USED: You tried to perform a specific operation

under conditions where that operation is prohibited.

OVER CURRENT: The system has detected a power

failure from a connected USB device or iPod/iPhone.

Remove the USB device or iPod/iPhone from the

system and turn the system power off then back on. If

the problem persists, contact your nearest Sony dealer.

PROTECT: The system has detected a power failure.

Unplug the AC adaptor. If the problem persists, contact

your nearest Sony dealer.

PUSH STOP: You pressed PLAY MODE  during

playback in the CD or USB function.

READING: The system is reading the information on the

disc, USB device, or iPod/iPhone. Some buttons do not

work during reading.

REMOVED: The connected USB device or iPod/iPhone

has been removed.

TIME NG: The Play Timer start and end times are set to

the same time.



Precautions

Discs that this system CAN play

Audio CD

CD-R/CD-RW (audio data/MP3 files)

Discs that this system CANNOT play

CD-ROM

CD-R/CD-RW other than those recorded in music CD

format or MP3 format conforming to ISO9660 Level

1/Level 2, Joliet

CD-R/CD-RW of poor recording quality,

CD-R/CD-RW that have scratches or are dirty,

or CD-R/CD-RW recorded with an incompatible

recording device

CD-R/CD-RW which is finalized incorrectly

Discs containing files other than MPEG 1 Audio Layer-

3 (MP3) files

Discs of non-standard shape (for example, heart,

square, star)

Discs that have adhesive tape, paper, or sticker attached

to them

Rental or used discs with attached seals where the glue

extends beyond the seal

Discs that have labels printed using ink that feels tacky

when touched

Notes on discs

Before playing, wipe the disc with a cleaning cloth from

the center out to the edge.

Do not clean discs with solvents, such as benzine,

thinner, or commercially available cleaners or anti-

static spray intended for vinyl LPs.

Do not expose discs to direct sunlight or heat sources

such as hot air ducts, nor leave it in a car parked in

direct sunlight.

On safety

Completely disconnect the power cord (mains lead)

from the wall outlet (mains) if it is not going to be used

for an extended period of time. When unplugging the

system, always grip the plug. Never pull the cord itself.

Should any solid object or liquid get into the system,

unplug the system, and have it checked by qualified

personnel before operating it again.

The AC power cord can be changed only by a qualified

service facility.

On placement

Do not place the system in an inclined position or in

locations that are extremely hot, cold, dusty, dirty, or

humid or lacking adequate ventilation, or subject to

vibration, direct sunlight or a bright light.

Be careful when placing the system on surfaces that

have been specially treated (for example, with wax, oil,

polish) as staining or discoloration of the surface may

result.

If the system is brought directly from a cold to a warm

location or is placed in a very damp room, moisture

may condense on the lens inside the CD player, and

cause the system to malfunction. In this situation,

remove the disc, and leave the system turned on for

about an hour until the moisture evaporates.

On heat buildup

Heat buildup on the unit during operation is normal

and is not cause for alarm.

Do not touch the cabinet if it has been used

continuously at a high volume because the cabinet may

have become hot.

Do not obstruct the ventilation holes.

On the speaker system

This speaker system is not magnetically shielded, and

the picture on nearby TV sets may become magnetically

distorted. In this situation, turn off the TV, wait 15 to

30 minutes, and turn it back on.

Cleaning the cabinet

Clean this system with a soft cloth slightly moistened

with a mild detergent solution. Do not use any type of

abrasive pads, scouring powder, or solvents, such as

thinner, benzine, or alcohol.



Specifications

Amplifier section

Power output (rated): 4 watts + 4 watts (8 ohms at 1 kHz, 1% THD)

Continuous RMS power output (reference): 5 watts + 5 watts (8 ohms at

1 kHz, 10% THD)

Input

AUDIO IN (stereo mini jack): Sensitivity 900 mV, impedance 47 kilohms

CD player section

System: Compact disc and digital audio system

Laser Diode Properties

Emission Duration: Continuous

Laser Output*: Less than 44.6 µW

* This output is the value measurement at a distance of 200 mm from the

objective lens surface on the Optical Pick-up Block with 7 mm aperture.

Frequency response: 20 Hz 20 kHz

Signal-to-noise ratio: More than 80 dB

Dynamic range: More than 80 dB

Tuner section

Antenna: FM lead antenna

AM loop antenna

FM tuner section

Tuning range:

87.5 MHz 108.0 MHz (50 kHz step)

AM tuner section

Tuning range:

European model:

531 kHz 1602 kHz (9 kHz step)

Latin American and Australian models:

530 kHz 1710 kHz (10 kHz step)

531 kHz 1710 kHz (9 kHz step)

Other models:

531 kHz 1602 kHz (9 kHz step)

530 kHz 1610 kHz (10 kHz step)

USB section

Supported bit rate:

MP3 (MPEG 1 Audio Layer-3): 32 kbps 320 kbps, VBR

WMA: 48 kbps 192 kbps, VBR

Sampling frequencies:

MP3 (MPEG 1 Audio Layer-3): 32/44.1/48 kHz

WMA: 44.1 kHz

(USB) port: Type A, maximum current 500 mA

iPod/iPhone section

USB works with:

iPhone 5s

iPhone 5c

iPhone 5

iPhone 4s

iPhone 4

iPhone 3GS

iPod touch (5th generation)

iPod touch (4th generation)

iPod touch (3rd generation)

iPod classic

iPod nano (7th generation)

iPod nano (6th generation)

iPod nano (5th generation)

iPod nano (4th generation)

The remote command of / and (enter) will only work with iPhone  

and iPod touch.

“Made for iPod,” and “Made for iPhone” mean that an electronic accessory

has been designed to connect specifically to iPod or iPhone, respectively, and

has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance

with safety and regulatory standards. Please note that the use of this

accessory with iPod or iPhone may affect wireless performance.

Speaker section

Full-range speaker: 80 mm, cone type

Rated impedance: 8 ohms

General

Power requirements:

Australian model:

AC adaptor

Input: 120 V 240 V AC, 50/60 Hz

Output: DC 9.5 V 1.8 A

Other models:

AC adaptor

Input: 110 V 240 V AC, 50/60 Hz

Output: DC 9.5 V 1.8 A

Power consumption: 13 watts

Dimensions (W/H/D):

Approx. 400 mm × 197 mm × 114 mm

Mass: Approx. 2.4 kg

Quantity of the main unit: 1 piece

Supplied accessories: Remote Commander (1), AC adaptor (1),

AM loop antenna (1), R6 (Size AA) batteries (2), Conversion plug adaptor

(Latin American model only) (1)

Design and specifications are subject to change without notice.

Standby power consumption: 0.5 W



Adjusting the sound

To Press

Adjust the volume VOLUME +/ .

Generate a more

dynamic sound

BASS BOOST .

Set the sound

effect

SOUND EFFECT repeatedly 

until desired sound effect is

displayed.

Each time you press this button,

sound effects are displayed in

the order “ROCK” “POP”  

“JAZZ” “FLAT.”

Changing the display

To Press

Change

information on

the display1)

DISPLAY  repeatedly when the

system is on.

Change Display

mode (see below.)

DISPLAY  repeatedly when the

system is off.

1) For example, you can view CD/MP3 disc information or the USB

device information, such as:

CD-DA disc

 remaining playing time of a track during playback

 total remaining playing time

MP3 disc/USB device

 track or file name (“ ”)

 artist name (“ ”)

 album name (“ ”)

The system offers the following display modes.

Display mode When the system is off

Power Saving

mode1)

The display is turned off to conserve

power. The timer and clock continue

to operate.

Clock2) The clock is displayed.

1) You cannot set the clock in Power Saving mode.

2) The clock display automatically turns to Power Saving mode after 8

seconds.

Notes on the display information

When the information includes double-byte characters, each double-

byte character will occupy 2 bytes

Characters that cannot be displayed appear as “_”

The following are not displayed:

 total playing time for an MP3 disc and a USB device

 total remaining playing time for an MP3 disc and a USB device

 remaining playing time for an MP3 file on MP3 disc or a MP3/

WMA file in USB device

The following are not displayed correctly:

 elapsed playing time of an MP3 file encoded using VBR (variable

bit rate)

 folder and file names that do not follow either the ISO9660

Level 1, Level 2, or Joliet in the expansion format

The following are displayed:

 total playing time for a CD-DA disc (except when PGM mode is

selected and the player is stopped)

 remaining playing time for a track of CD-DA disc

 remaining playing time for a CD-DA disc (only when Normal Play

mode is selected during playback)

 ID3 tag information for MP3 files when ID3 version 1 and

version 2 tags are used (ID3 version 2 tag information display has

priority when both ID3 version 1 and version 2 tags are used for a

single MP3 file)

 up to 64 characters for an ID3 tag, where characters allowed are

uppercase letters (A to Z), lowercase letters (a to z) (lowercase will

be displayed as uppercase), digits (0 to 9), and symbols (˝ $ % ’ ( )

* + , – . / < = > ? @ [ \ ] `)

Using the timers

The system offers 2 timer functions. If you use both

timers, the Sleep Timer has priority.

Sleep Timer:

You can fall asleep to music. This function works even if

the clock is not set.

Press SLEEP  repeatedly.

With each press of SLEEP , the setting time is

decreased by 10 minutes from a maximum of 90 minutes

to minimum of 10 minutes.

To cancel the Sleep Timer, select “OFF.”

Play Timer:

You can wake up to CD, FM/AM reception, USB device,

or iPod/iPhone at a preset time. Make sure you have set

the clock.

1 Prepare the sound source.

Prepare the sound source, and then press VOLUME

+/  to adjust the volume. You can set the CD,

USB (including iPod/iPhone), FM, or AM function as

the sound source.

To start from a specific CD track, audio file, and radio

station create your own program.

2 Select the timer set mode.

Press TIMER MENU .

3 Set the play timer.

Press /    repeatedly to select “PLAY SET,” then

press .

4 Set the time to start playback.

Press /    repeatedly to set the hour, then press

. Use the procedure above to set the minutes.

5 Use the same procedure as in step 4 to set the time

to stop playback.

6 Select the sound source.

Press /    repeatedly until the desired sound

source appears, then press .

7 Turn off the system.

Press . The system automatically turns on

before the preset time.

If the system is on at the preset time, the Play Timer

will not play. Do not operate the system from the time

the system turns on until the playback starts.



The audio formats that you can listen to with this system are as

follows:

 MP3: file extension “.mp3”

 WMA: file extension “.wma”

Note that even when file name has the correct file extension,

if the actual file differs, the system may produce noise or may

malfunction.

To use the system as a battery charger

You can use the system as a battery charger for USB

devices that have a recharge function when the system

is on.

Charging begins when the USB device is connected to

a (USB) port . The charging status appears on the

USB device display. For details, see the user’s guide for

your USB device.

To stop charging the USB device

Remove the USB device.

Note on charging the USB device

You cannot charge a USB device when the system is off.

Playing the iPod/iPhone

1 Connect the USB cable supplied with the iPod/

iPhone to the (USB) port  on the unit.

2 Select the USB function.

Press USB FUNCTION  on the remote or press

FUNCTION  on the unit repeatedly.

3 Start playback after confirming “iPod” appears on

the display.

Press  on the remote or press  on the

unit.

To control the iPod/iPhone

To Press

Pause playback      / (or  on the

unit).

Pause  

Select a track

or chapter of

audiobook/

podcast

 / . To fast-forward or

fast-rewind, hold down the button.

Find a point in a

track or chapter

of audiobook/

podcast

Hold down /    during

playback, and release the button at

the desired point.

Choose the

selected item

/ .

Scroll up/down

the iPod menus

 / .

Return to the

previous menu

RETURN /  .

To use the system as a battery charger

You can use the system as a battery charger for an iPod/

iPhone while the system is on.

To see whether charging is operating or not, check

the battery icon of the iPod/iPhone display. Check the

“iPod/iPhone section” of the “Specifications” for a list of

iPod/iPhone models compatible with this system.

To stop charging an iPod/iPhone

Remove the connected iPod/iPhone from the unit.

Notes

The performance of the system may be vary, depending on the

specifications of your iPod/iPhone.

When an iPod/iPhone is being connected with the unit via a USB

port, first “CONNECT” then “iPod” will be displayed.

Do not carry the system with an iPod/iPhone connected to the

system. Doing so may cause a malfunction.

When connecting or disconnecting the iPod/iPhone, brace the

system with one hand and take care not to press the controls of the

iPod/iPhone by mistake.

To use an iPod/iPhone, refer to the user’s guide of your iPod/iPhone.

Sony cannot accept responsibility in the event that data recorded to

iPod/iPhone is lost or damaged when using an iPod/iPhone with

this system.

Using optional audio components

1 Prepare the sound source.

Connect additional audio component to the AUDIO

IN jack  on the unit using an audio analog cord

(not supplied).

2 Turn down the volume.

Press VOLUME .

3 Select the AUDIO IN function.

Press AUDIO IN FUNCTION  on the remote or

press FUNCTION  on the unit repeatedly.

4 Start playback.

Start playback of the connected component and adjust

the volume.

Note

The system may enter Standby mode automatically if the volume

level of the connected component is too low. Adjust the component’s

volume accordingly. See “To turn off the Automatic Standby function.”



Produktspezifikationen

Marke:	Sony
Kategorie:	Hi-Fi-Anlage
Modell:	CMT-V11iP

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sony CMT-V11iP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Hi-Fi-Anlage Sony

Sony MHC-GPX555 Bedienungsanleitung

30 September 2024

Sony Walkman NW-A105 Bedienungsanleitung

13 September 2024

Sony HCD-451 Bedienungsanleitung

3 September 2024

Sony DHC-MD373 Bedienungsanleitung

2 September 2024

Sony HST-211 Bedienungsanleitung

31 August 2024

Sony SHAKE-99 Bedienungsanleitung

30 August 2024

Sony SHAKE-55 Bedienungsanleitung

30 August 2024

Sony SHAKE-X3D Bedienungsanleitung

30 August 2024

Sony SHAKE-77 Bedienungsanleitung

30 August 2024

Sony MHC-GNZ8D Bedienungsanleitung

21 August 2024

Bedienungsanleitung Hi-Fi-Anlage

Neueste Bedienungsanleitung für -Kategorien-

Lenco MC-129 MP3 Bedienungsanleitung

16 Oktober 2024

Akai EIE Pro Bedienungsanleitung

14 Oktober 2024

Sennheiser SZI 1029 Bedienungsanleitung

7 Oktober 2024

Yamaha MusicCast SRT-1500 Bedienungsanleitung

7 Oktober 2024

Kicker 46HDTPH Bedienungsanleitung

7 Oktober 2024

Vtech V-Kids Bedienungsanleitung

5 Oktober 2024

Hitachi AX-M10E Bedienungsanleitung

5 Oktober 2024

IDance XD8N Bedienungsanleitung

5 Oktober 2024

LD Systems DAVE 18 G3 Bedienungsanleitung

4 Oktober 2024

Pyle Pro PWMA1216BM Bedienungsanleitung

4 Oktober 2024