Sjoef Dolly BIS12M2 Bedienungsanleitung

Sjoef Fahrrad Dolly BIS12M2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sjoef Dolly BIS12M2 (17 Seiten) in der Kategorie Fahrrad. Dieser Bedienungsanleitung war für 48 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/17
1
Instrucons Manual
keep this manual
Handbuch
Bewahren Sie dieses Handbuch
Handleiding
Bewaar deze handleiding
S J O E F
Amsterdam
Made in India
in India hergestellt
Gemaakt in India
Bisshops BV
Herengracht 338
1016 CG Amsterdam
The Netherlands
2
EN - Manual
This manual provides instrucons for assembling and maintaining your new SJOEF
bicycle. Before assembling the bicycle, it is important to follow these steps. As-
sembly is intended for adults only
• Remove the bicycle from the packaging and remove the packaging materials.
The bicycles are manufactured to comply with the European standards EN
ISO-8098:2014 (maximum saddle height from 435mm to 635mm) or EN ISO-
4210:2014 (minimum saddle height of 635mm). Please note: the manufacturer is
not responsible for improper use or incorrect assembly of the bicycle. Please verify
with the local authories which regulaons apply to the use of children’s bicycles
on public roads. Ensure compliance with these rules at all mes. Always inspect
the surface of the terrain where the bicycle will be ridden and make sure that a
parent/guardian is always supervising the child during use. Improper use of the
bicycle can result in hazardous situaons.
Ensure that the child is always given clear instrucons on the use and dangers
associated with using the bicycle. In parcular, the use of the brakes should be
clearly explained.
Assembly
The bicycle can be assembled in a few simple steps. It is important to follow the
order of the instrucons in order to make the assembly as easy as possible.
Mounng the saddle
1. Aach the saddle post to the seat tube. Pay aenon to the safety mark
on the saddle post, which must not be exceeded. The maximum height is
reached when the safety mark is visible. The minimum height is reached when
the saddle bolt is completely loosened.
2. The saddle is at the correct height when your child can just touch the ground
on both sides of the bike. Preferably, the heel also touches the ground.
3. Tighten the saddle bolt to the desired height.
Installing the handlebar and stem (if required)
1. Aach the cone to the stem by ghtening the bolt (if necessary).
2. Insert the stem (including handbrake lever) into the frame.
3. Posion the handlebar at the desired height and check whether it is perpen-
dicular to the front wheel.
4. Tighten the handlebar clamp and/or bolt.
5. Mount the bell on the leî™› side of the steer next to the grip.
3
Installing the pedals
PLEASE NOTE: there is an (L) on the leî™› and an (R) on the right side of the pedal.
Incorrectly ghtening the pedal will render the bike unusable and will void the
warranty.
1. It is advisable to grease the ends of the pedals so that they can be replaced
easily in the future.
2. An L or R can be read o from the axle of the pedal. Use this to check which
pedal should be ed on the le and which on the right. Are there no L or R
on the pedals? Then the leî™› pedal contains a marking in the form of a line.
(le or right is viewed from the sing posion on the bicycle).
3. Insert the right pedal into the crank and turn the pedal clockwise by hand
towards the front wheel. It should be easy to turn the pedal; if it is s, the
thread may be damaged.
4. Then turn the leî™› pedal by hand counter-clockwise into the crank, also in the
direcon of the front wheel.
5. Finally, ghten the pedals even further using an open-end spanner.
Fiî¾®ng the side wheels (if available)
1. Loosen the rear axle bolts and remove the fender stay.
2. Fit the support wheel arm on the rear axle against the locking plate which is
already ed on the rear axle). Make sure the rear wheel does not slide in the
frame.
3. Screw the outer axle nut ght when the desired height of the side wheels has
been found. The side wheels should stay about 6 mm above the ground on
both sides.
4. The use of training wheels entails risks, handle them with care.
Handlebar pad
Use these cushions by aîš‚aching them to the handlebars and stem with the Velcro
strap.
The hand brake
The hand brake is already mounted on the bike. Check whether the brake blocks
press rmly on the rim when braking. Adjust them if necessary and do this regular-
ly:
1. If the margin in the brake handle is too large, ghten the brake cable nut at
the handle to make it ghter.
2. Double check to see if the brake pads are pressing rmly against the rim
when you squeeze the handbrake. If the pads do not t properly on the rim or
if they are crooked, you can unscrew the inner cable nut.
3. Next, straighten the brake pads with one hand. With the other hand, pull on
the inner cable and ghten the inner cable nut again.
4. You can adjust the distance between the brake blocks and rim by turning the
adjusng screw clockwise if further adjustment of the brakes is needed. Make
sure that the brake cable is rmly connected to the brake cable nut when
adjusng.
5. Lastly, ghten the lock nut securely.


Produktspezifikationen

Marke: Sjoef
Kategorie: Fahrrad
Modell: Dolly BIS12M2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sjoef Dolly BIS12M2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fahrrad Sjoef

Bedienungsanleitung Fahrrad

Neueste Bedienungsanleitung für -Kategorien-