Singer 1004 VIVO Bedienungsanleitung
Singer
Nähmaschine
1004 VIVO
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Singer 1004 VIVO (27 Seiten) in der Kategorie Nähmaschine. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/27
INSTRUCTION MANUAL
Why is the thread looping/bunching under my fabric?
Thread looping under your fabric is usually caused by not threading the upper tension
correctly. With the presser foot lever in the UP position and tension set at 4, follow the
threading guides/graphics on the top of the machine.
1.Place the thread spool on the spool pin and secure with a thread spool cap.
2.While holding the thread with your right hand, use your left hand to take the thread and
take the thread and follow the thread path by bringing the thread down into the tension
channel around the bottom and up the other side.Continue to thread the machine, but do
not thread the needle.
Before threading the needle, perform this easy test to make sure the upper thread is
threaded correctly. Making sure the presser foot is raised, pull the thread. It should pull
easily. Now lower the presser foot, the thread should now resist when you pull it. There
should be a significant increase in the tension of the thread. If there is no increased
tension, the machine is not threaded correctly.
Why is my machine skipping stitches?
Skipped stitches can occur if needles are damaged or dull, or if they are incorrectly
inserted into the machine.
First, your needle may be dull or damaged and need to be replaced. You should also
check that you are using the correct needle for the type of fabric you are sewing. Refer
to the Needle/Fabric/Thread/Guide on page 11 of this manual.
Next, check that the needle is installed correctly. The needle needs to be pushed as far up
the needle shaft as possible. (It's easy to insert the needle halfway, clamp it down and think
it is installed correctly.) Also, the flat part of the needle should be positioned towards the
back. If the needle is not installed correctly, it will not be able to pull up the bobbin thread
and will cause skipped stitches.
Vivo 1004-
TM
IMPORTANT SAFETY INSTRUCTIONS
This machine is intended for household use only. Read all instructions before using this
create & repair machine.
When using an electrical appliance, basic safety should always be followed in order to
reduce the risk of burns, fire, electric shock or injury to persons, including the following:
SINGER and VIVO are exclusive trademarks of The Singer
Company Limited S.à.r.l. or its Affiliates.
©2013 The Singer Company Limited S.à.r.l. or its Affiliates.
All rights reserved.
12
Model 1004 VIVO INSTRUCTION MANUAL
This machine is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety. Children should be supervised to ensure that
they do not play with the appliance.
The sound pressure level under normal operation conditions is .
Turn off or unplug the machine when it is not operating properly.
Never place anything on the foot controller.
If the power supply cord is damaged, it must be replaced by the manufacturer or its
service agent or similarly qualified person in order to avoid a hazard.
72db
1. The machine should never be left unattended when plugged in.
2. Always unplug the machine from the electrical outlet immediately after using and
before cleaning.
3. Always unplug before re-lamping. Replace bulb with the same type rated
4. Do not allow to be used as a toy. Close supervision is necessary when the machine
is used by or near children.
5. Use this machine only for its intended use, as described in this manual. Use only
attachments recommended by the manufacturer as contained in this manual.
6. Never operate this machine if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the
machine to the nearest authorized retailer or service center for examination, repair,
or electrical or mechanical adjustment.
7. Never operate the machine with any air openings blocked. Keep ventilation
openings of the sewing machine and foot controller free from accumulation of lint,
dust and loose fabrics.
8. Keep fingers away from all moving parts. Special care is required around the
sewing machine needle.
9. Always use the proper needle plate. The wrong plate can cause the needle to break.
Do not use bent needles.
Do not pull or push the fabric while stitching, as this may deflect the needle,
causing it to break.
Switch the sewing machine off when making any adjustments in the needle area,
such as threading the needle, changing the needle, threading the bobbin, changing
the presser foot, etc.
Always unplug the sewing machine from the electrical outlet when removing covers,
lubrication, or when making any other user servicing adjustments mentioned in the
instruction manual.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol spray products are being used or where oxygen is
being administered.
To disconnect, turn all controls to the off position, then remove the plug from the
electrical outlet.
Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
We recommend that before you start to use your create & repair machine, you take time to
review this instruction book, seated at the machine. You will discover that this machine is
not only easy to use, but it offers many features designed to make your sewing experience
enjoyable.
INTRODUCTION
Produktspezifikationen
| Marke: | Singer |
| Kategorie: | Nähmaschine |
| Modell: | 1004 VIVO |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Singer 1004 VIVO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nähmaschine Singer
13 Oktober 2024
30 September 2024
30 September 2024
23 September 2024
16 September 2024
15 September 2024
14 September 2024
9 September 2024
4 September 2024
4 September 2024
Bedienungsanleitung Nähmaschine
- Nähmaschine Juki
- Nähmaschine Sinbo
- Nähmaschine Emerio
- Nähmaschine Tristar
- Nähmaschine Medion
- Nähmaschine SilverCrest
- Nähmaschine Bestron
- Nähmaschine Guzzanti
- Nähmaschine AEG
- Nähmaschine Alfa
- Nähmaschine Ambiano
- Nähmaschine Siemens
- Nähmaschine Jata
- Nähmaschine Lervia
- Nähmaschine IKEA
- Nähmaschine Durabase
- Nähmaschine Blaupunkt
- Nähmaschine Hema
- Nähmaschine Home Electric
- Nähmaschine Micromaxx
- Nähmaschine Mio Star
- Nähmaschine Solac
- Nähmaschine Privileg
- Nähmaschine Livoo
- Nähmaschine Easy Home
- Nähmaschine Prixton
- Nähmaschine Lifetec
- Nähmaschine Husqvarna
- Nähmaschine Termozeta
- Nähmaschine Crofton
- Nähmaschine Brother
- Nähmaschine Kohler
- Nähmaschine Primera
- Nähmaschine Veritas
- Nähmaschine Toyota
- Nähmaschine Janome
- Nähmaschine Victoria
- Nähmaschine Kayser
- Nähmaschine Jocca
- Nähmaschine Aigger
- Nähmaschine EasyMaxx
- Nähmaschine Bernina
- Nähmaschine Elna
- Nähmaschine Necchi
- Nähmaschine Pfaff
- Nähmaschine Dürkopp Adler
- Nähmaschine W6
- Nähmaschine E&R
- Nähmaschine Carina
- Nähmaschine Empisal
- Nähmaschine ER
- Nähmaschine Feiyue
- Nähmaschine Gritzner
- Nähmaschine Hofmann
- Nähmaschine Huskystar
- Nähmaschine Husqvarna-Viking
- Nähmaschine Kenmore
- Nähmaschine Lewenstein
- Nähmaschine Mediashop
- Nähmaschine Muller
- Nähmaschine Novamatic
- Nähmaschine Siemssen
- Nähmaschine Silver
- Nähmaschine Sinojo
- Nähmaschine Tesco
- Nähmaschine Vendomatic
- Nähmaschine Weasy
- Nähmaschine Yamata
- Nähmaschine Zippy
- Nähmaschine Union Special
- Nähmaschine Kunft
- Nähmaschine Meister Craft
- Nähmaschine RCE
- Nähmaschine Yamato
- Nähmaschine Baby Lock
- Nähmaschine Łucznik
- Nähmaschine Anker-Bernette
- Nähmaschine LERAN
- Nähmaschine Prince
- Nähmaschine Bernette
- Nähmaschine Sewmaq
- Nähmaschine SteamMax
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024