Siemens WM16S890EU Bedienungsanleitung

Siemens Waschmaschine WM16S890EU

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Siemens WM16S890EU (10 Seiten) in der Kategorie Waschmaschine. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/10

Safety instructions

 The washing machine is heavy  take care when lifting it.

 Warning: Frozen hoses may tear/burst. Do not install the washing machine in an area where

there is a risk of frost or outdoors.

 Do not hold onto protruding parts (e.g. loading door) when lifting. Washing machine may

be damaged.

 Before transporting the appliance, always drain dispensers. aPage 8

 In addition to the safety information listed here, the local water and electricity supplier may

have special requirements.

 If in doubt, have the appliance connected by a technician.

 Lay hoses and cables in such a way that there is no risk of stumbling.

Environmental disposal

  Dispose of packaging in an environmentally friendly manner.

 This appliance has been identified in accordance with the European Directive 2002/96/EG

on Waste Electrical and Electronic Equipment (WEEE).

The Directive specifies the framework for an EU-wide valid return and recycling of waste

appliances.

Installation area

 Stability is important to prevent the machine from moving!

 The installation area must be firm and level.

 Soft floors/floor coverings are not suitable.

If installing the appliance on a base

 secure the washing machine feet with retention plates *.Always

* Order no. WMZ 2200, WX 9756, CZ 110600, Z 7080X0

If installing the appliance on a wooden joist ceiling

 If possible, install the washing machine in a corner.

 Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.

 secure the washing machine feet with retention plates.Always

* Order no. see above

Installation on a platform with drawer*

* Order no. WMZ20490, WZ20490

Built-under/Built-in appliance

Build-under/Build-in before connection to the power supply.

Installed in between kitchen units (built-under or built-in)

 60 cm cavity width required.

 Install washing machine only under a continuous worktop connected firmly to the adjacent

cupboards.

Built-under

Risk of electric shock!

 Instead of the appliance cover panel, it is to have a technician fit a sheet metal essential

cover *. * Order no. WMZ 2043, WZ 20430

 60 cm cavity width required.

Scope of delivery depending on model

not included in product package:

When drainage is into a siphon, a Ø 2440 mm hose clip (specialist outlet) is also required.

a Water connection, Page 4

Useful tools:

 Spirit level for aligning the washing machine.

 Size 13 socket wrench:

for loosening the transportation protection devices and aPage 3

size 17: for aligning the appliance feet. aPage 5

Hose and cable lengths depending on model

Connection on left side or Connection on right side

Note: If the hose holders are used, the possible hose lengths are reduced!

Available from dealer/customer service:

 Extension for Aqua-Stop or cold water inlet hose (approx. 2.50 m).

Order no. WMZ2380, WZ10130, CZ11350, Z7070X0

 Longer supply hose (approx. 2.20 m), for standard model.

Spanner

(depending on model)

Power cord

Water supply

Water drainage

Elbow

for securing the

drainage hoseCovers

Aqua Stop Aqua-Secure

~140 cm

~95 cm

~120 cm

~130 cm

~100 cm

~135 cm

0  max. 100 cm

Humidity in the drum

is caused by the final

inspection.

Remove transportation protection devices

 Before using the appliance for the first time, remove the

4 transportation protection devices completely and keep in a safe

place.

 If the appliance is to be transported at a later date, re-install the

transportation protection devices  prevents damage to the machine.

aPage 6

 Keep screw and sleeve together.

1. Take hoses (depending on model) out of the

holders and the elbow. Remove the elbow.

2. Loosen and remove all 4 transportation lock screws.

3. Take the power cord out of the holders.

Remove sleeves.

4. Insert covers and lock firmly by pressing on the locking hook at the top.

Water connection depending on model

 Do not immerse Aqua-Stop safety device in water (contains Risk of electric shock!

an electric valve).

 To prevent leakage or water damage, follow the instructions in this chapter!

 The washing machine must only be operated with cold tap water.Caution:

 Do not connect to the mixer tap of an unpressurised hot-water apparatus.

 Use only the supplied inlet hose or one purchased from an authorised specialist outlet,

not a used one!

 If in doubt, have the appliance connected by a technician.

Water supply

Water inlet hose:

Caution: do not kink, crush, modify or sever

(strength is no longer guaranteed).

Optimum water pressure in the mains: 1001000 kPa (110 bar)

 When the tap is turned on, the water flow is at least 8l/min.

 If the water pressure is higher, install a pressure reducing valve.

Model: Aqua-Stop

Aqua-Secure

Standard

1. Connect water inlet hose to a 3/4" = 26.4 mm tap.

Caution: Tighten plastic screw-fittings by hand only.

2. Carefully turn on the tap and check that the connection

points are not leaking.

Caution: Screw connection is under water pipe

pressure.

Water drainage

Water drainage hose:

Caution: Do not bend or pull.

Height difference between installation area and outlet:

0  max. 100 cm

 Drainage into a washbasin:

Caution: Secure the drainage hose to prevent it from slipping out of the

sink.

Caution: The plug must not block the drain of the wash basin. When the

water is being pumped out of the washing machine, check that the water

drains away quickly enough. The end of the drainage hose must not be

immersed in the drained water! Risk of water being drawn back into the

washing machine!

 Drainage into a siphon:

Caution: Connection point must be secured with hose clip, Ø 2440 mm

(specialist outlet).

.  Drainage into a plastic pipe with rubber sleeve or into a gully:

Caution: Secure the drainage hose to prevent it from slipping out of the

sink.

max.

90°

max.

90°

min.

10 mm

min.

10 mm

3/4

Alignment

Loud noise formation, intense vibrations and wandering may be due to incorrect

alignment!

Align washing machine with spirit level

1. Loosen lock nut in a clockwise direction with a wrench.

2. Change height by rotating the appliance feet.

Caution: All four feet must be firmly on the floor.

The washing machine must not wobble!

Check alignment of the washing machine with a spirit level and, if

required, correct.

3. Tighten the lock nut against the housing.

Grip the foot and do not adjust the height.

Caution: The lock nuts on all four appliance feet must be screwed tightly

against the housing!

Electrical connection

ʑConnect the washing machine to an alternating current via a correctly installed

earthed socket only.

ʑThe mains voltage and voltage specifications on the washing machine (appliance

rating plate on the rear of the appliance) must match.

ʑConnected load as well as required fuse are indicated on the appliance rating plate.

ʑEnsure that:

 the mains plug and socket match,

 the cable cross-section is adequate,

 the earthing system has been installed correctly.

ʑA damaged power cord may be replaced by an electrician only.

A replacement mains cable can be obtained from customer service.

ʑDo not use multiple plugs/couplings or extension cables.

ʑIn the event that an earth leakage circuit breaker is to be used, only use types

marked with the following symbol: .

Only this symbol can guarantee compliance with all current regulations.

ʑMains plug:

 Do not insert/pull out with damp hands.

 Do not pull by tugging the power cord.

 Never pull it out during operation.

max. 12 mm

Transportation, e.g. if moving house

1. Before transporting the washing machine:

1. Turn off the tap.

2. Drain any residual washing solution. aPage 12

3. Release the water pressure in the supply hose. a Page 12

4. Isolate the washing machine from the power supply.

5. Remove the hoses.

6. Drain dispensers. aPage 8

2. Installing transportation protection devices:

1. Remove covers and keep

in a safe place.

If required, use a

screwdriver.

2. Insert all 4 sleeves.

Clamp mains cable on the

holders. Insert and tighten

the bolts.

3. Before switching on the appliance again,

remove the transportation protection devices! a Page 3

To prevent unused detergent from flowing into the outlet during the first wash: Pour 1 litre of

water into dispenser and start the programme.B/CEmpty

Aqua-Stop warranty For appliances with Aqua-Stop only

In addition to warranty claims against the seller based on the contract of sale and in addition

to our appliance warranty we shall pay damages under the following conditions:

1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private

users for damage.

2. The liability warranty applies to the service life of the appliance.

3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been

correctly installed and connected according to our instructions; this also includes a correctly

installed Aqua-Stop extension (original accessory).

Our warranty does not apply to defective supply lines or fittings up to the Aqua-Stop

connection on the tap.

4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not

necessary to turn off the tap afterwards.

The tap should only be turned off if you are away for a prolonged period, e.g. several weeks

holiday.

Technical specifications

ʑ Dimensions (width x depth x height) 60 x 59 x 85 cm

ʑ Weight 63  83 kg depending on model

ʑ Mains connection Nominal voltage 220  240 V, 50 Hz

Nominal current 10 A

Nominal power 2300 W

ʑ Water pressure 100  1000 kPa (1  10 bar)

Manufacturer aOperating instructions

9301/9000853267

*853267*

Care

ʑMachine housing, control panel

 Remove detergent residue immediately.

 Wipe with a soft, damp cloth.

 Do not clean the appliance with a water jet.

ʑDrum

Use chlorine-free cleaning agent, not steel wool.

ʑDescaling

Not required if detergent dosed correctly. However, if this does occur, follow the instructions

of the descaling agent manufacturer.

ʑi-DOS/i-Dos: Clean the detergent drawer

Drain dispensers:

The dispensers have drainage openings with removable stoppers in the front area.

To drain the dispensers, first remove the drawer handle as illustrated:

1. Open detergent drawer.

2. Pull release lever (A) on the back of the drawer

handle (bottom middle) gently towards yourself

and simultaneously ...

... pull up released drawer handle (B).

To drain the dispensers, carefully remove the respective sealing plug

and drain the contents into a suitable receptacle.

Re-insert sealing plug fully.

 Pull out the mains plug.Risk of electric shock!

 No solvents.Risk of explosion!

Care

Clean dispensers/detergent drawer:

To clean the drained dispensers, the detergent drawer can be completely removed.

1. Drain dispensers before removing them. aPage 8.

Note: Re-attach drawer handle only after cleaning.

2. Open drawer.

3. Press release lever and completely remove drawer.

3. Carefully remove drawer cover.

Do not clean the cover in the dishwasher (contains electrical components) and do not

immerse in water.

Protect rear drawer plug from moisture, detergent or softener residue; if required clean

outer surfaces with a soft, damp cloth. Dry before re-inserting.

4. Clean tray and cover with soft, damp cloth or hand

shower. Clean inner surfaces with a soft, damp cloth.

5. Dry tray and cover and re-assemble.

6. Push on drawer handle from above until it locks

in place.

7. Push in detergent drawer all the way.

 Pull out the mains plug.Risk of electric shock!

 No solvents.Risk of explosion!

What to do if 

ʑ ... water runs out:  Correctly attach/replace drainage hose.

 Tighten screw-fitting on the supply hose.

ʑ ... no water runs in:  /Reload not selected?Start

 Tap not open?

 Filter blocked? Clean filter. aPage 12

 Supply hose kinked or jammed?

ʑ... dispenser is empty

and fill level display is not

flashing:

 Drawer cover/rear drawer plug dirty? Clean.

a Page 8, 9

 Detergent drawer not inserted correctly?

Insert correctly. aPage 8, 9

ʑ... wrong detergent/

softener has been

poured into dispenser:

 Drain dispensers. aPage 8 Page 9, clean a and refill

dispensers. aOperating instructions, Page 11

ʑ... detergent/softener

congealed in the

dispensers:

 Clean and refill dispensers.

ʑ... the washing machine

door cannot be opened:

 Safety function active. Stop programme? a

Operating instructions, Page 5

 (without final spin) selected? Rinse hold c a

Operating instructions, Page 6

 Can be opened via emergency release only? aPage 13

ʑ... programme does not

start:

 /Reload or selected?Start end time

 Door closed?

 Childproof lock active? Deactivate. a

Operating instructions, Page 9

ʑ... detergent solution is

not drained:

 (without final spin) selected? Rinse hold c a

Operating instructions Page 6,

 Clean detergent-solution pump. aPage 12

 Clean outlet pipe and/or drainage hose.

ʑ... Water not visible in the

drum:

 Not a fault  water below the visible area.

ʑ... spin result not

satisfactory, washing

wet/too damp:

 Not a fault  unbalanced load detection system has stopped the

spin cycle, washing unevenly distributed.

Distribute small and large items of washing in the drum.

 selected? Anticrease /Easy-iron   a

Operating instructions, Page 6

 Too low speed selected? aOperating instructions, Page 2

ʑ... the programme

duration changes during

the wash cycle:

 Not a fault  the programme sequence is optimised for the

particular wash process. This may result in changes to the

programme duration in the display field.

ʑ ... is spun several times:  Not a fault  unbalanced load detection system adjusts

imbalance.

ʑ... odours form in the

washing machine:

 Run Cottons 90 °C programme without washing. To do this, use

a little standard detergent.

ʑ... status display ³3

flashes, foam may run

out of the detergent

drawer:

 Too much detergent used? Mix 1 tablespoon of softener with

½ litre of water and pour into manual dispenser /B C (not for

outdoor, sports and down-filled textiles!).

 Reduce detergent dosage for the next wash cycle.

Reduce basic dosage. aOperating instructions, Page 12

ʑ... detergent/fabric

softener drips off the seal

and collects on the glass

or in the seal fold:

 Too much detergent/fabric softener in dispensers.

Observe mark in the dispensers.max

What to do if 

ʑ... loud noise, vibrations

and wandering occur

during the spin cycle:

 Appliance feet fixed?

Secure appliance feet. aPage 5

 Transportation protection devices removed?

Remove transportation protection devices. aPage 3

ʑ... noises occur during

spin and drain cycles:

 Clean the drain pump. aPage 12

ʑ... display panel/indicator

lights do not function

while the appliance is

running:

 Energy saving mode active. aOperating instructions, Page 1

 Power failure? If required, switch on/replace domestic fuse.

ʑ... the programme takes

longer than usual:

 Not a fault  unbalanced load detection system adjusts

imbalance by repeatedly distributing the washing.

 Not a fault  foam detection system active  rinse cycles are

switched on.

ʑ... detergent residue on

the washing:

 Powder detergents occasionally contain water-insoluble residue.

 Select programme or brush washing.Rinse

 Use liquid detergent.

ʑ... in the reload status

Start/Reload flashes very

quickly and a signal

sounds:

 Water level too high. Immediately close washing machine door.

 Select Start/Reload to continue the programme.

If a fault cannot be rectified by following the above instructions or by switching the machine

off and on, or if a repair is required for a different reason:

 Set programme selector to and pull out the mains plug.Off

Turn off the tap and call customer service. a Operating instructions, Page 13

Information on the display panel depending on model

Door open? Close the washing machine door properly; washing may be caught.

Tap closed?

 Turn on tap fully.

 Supply hose kinked/jammed.

 Clean filter. aPage 12

 Water pressure too low.

Top up i-Dos1/i-Dos2 Level i-Dos1/i-Dos2 below minimum, top up. aOperating

instructions, Page 12

i-Dos error

Deactivate i-Dos

Set i-Dos1/i-Dos2 to . , call OFF aOperating instructions, Page 12

customer service. Appliance can continue to be operated with manual

dosage.

Drawer closed? Push in detergent drawer correctly.

Pump blocked?

Filter blocked; clean detergent-solution pump. aPage 12

Drainage hose/outlet pipe blocked; clean drainage hose on the

siphon. aPage 12

Pause no reload;

water level too high

or temperature too high

Washing cannot be reloaded. Select Start/Reload to continue the

programme.

Aqua-Stop activated Water in the base pan, appliance leaking. Call customer service!

Other displays

Switch off appliance, wait 5 seconds and switch on again. If the display

is indicated again, call customer service. a

Operating instructions, Page 13

What to do if 

Drain pump blocked

Set programme selector to , pull out the mains plug.Off

1. Open and remove service flap.

2. Take the drainage hose out of the holder.

Remove sealing cap, allow detergent solution to flow out.

Put the closing cap back on the hose.

3. Carefully unscrew the pump cover (residual water).

4. Clean the interior, pump cover thread and pump housing (fan impeller

in the detergent-solution pump must rotate).

5. Reinsert and screw on pump cover. Handle is upright.

Insert the drain hose into the holder.

6. Insert and close service flap.

To prevent unused detergent from flowing into the outlet during the next wash:

Pour 1 litre of water into dispenser / and start the programme.B C Empty

Drainage hose on the siphon blocked

Set programme selector to , pull out the mains plug.Off

1. Loosen hose clip, carefully remove drainage hose (residual water).

2. Clean drainage hose and siphon spigot.

3. Re-attach drainage hose and secure connection point with hose clip.

Filters blocked in water inlet hose

Risk of electric shock!

Do not immerse Aqua-Stop safety device in water (contains electric valve).

First, release water pressure in the supply hose:

1. Turn off the tap!

2. Spin/EmptySelect any programme (except ).

3. StartSelect /Reload. Leave programme for approx. 40 seconds.

4. OffSet programme selector to . Pull out the mains plug!

5. Clean the filters:

Disconnect the hose from the water tap.

Clean filter with small brush.

and/or for standard and Aqua-Secure models:

remove hose from the rear of the appliance.

Take out filter with pliers and clean.

6. Connect the hose and check for leaks.

 Risk of scalding!

Allow detergent solution to cool

down.

Emergency release

e.g. if power failure occurs

The programme continues running when the power supply is restored. If the washing is still

to be removed, the door can be opened as described below:

Risk of scalding!

Wash liquor and washing may be hot. If required, leave to cool down.

Do not reach into the drum in case it is still rotating.

Do not open the door if you can still see water through the glass.

1. OffSet programme selector to , pull out the mains plug.

2. Drain detergent solution. aPage 12

3. Pull down emergency release ( ) with a tool and release.aarrow

4. Door can then be opened.

 Risk of scalding!

Allow detergent solution to cool down.

 Close the mains water tap.

Washing machine

with Intelligent Dosage

System

Contents Page

ʋSafety instructions. . . . . . . . . . . . . . . . . . 1

ʋEnvironmental disposal . . . . . . . . . . . . . . 1

ʋInstallation area . . . . . . . . . . . . . . . . . . . 1

ʋBuilt-under/Built-in appliance . . . . . . . . . 1

ʋScope of delivery . . . . . . . . . . . . . . . . . . 2

ʋHose and cable lengths . . . . . . . . . . . . . 2

ʋRemoving transportation safety devices 3

ʋWater connection . . . . . . . . . . . . . . . . . . 4

ʋAligning the appliance. . . . . . . . . . . . . . . 5

ʋElectrical connection. . . . . . . . . . . . . . . . 5

ʋTransportation, e.g. if moving house . . . . 6

ʋAqua-Stop warranty. . . . . . . . . . . . . . . . . 6

ʋTechnical specifications . . . . . . . . . . . . . 7

ʋCare . . . . . . . . . . . . . . . . . . . . . . . . . . 8/9

ʋWhat to do if ... . . . . . . . . . . . . . . . 10  12

ʋInformation on the display panel . . . . . . 11

ʋEmergency lock release . . . . . . . . . . . . 13

Installation/

Maintenance instructions

What to do if 

Read these instructions before switching on the washing machine!

Also follow the separate operating instructions.

Retain all documents for subsequent use or for the next owner.

Safety instructions

 The washing machine is heavy  take care when lifting it.

 Warning: Frozen hoses may tear/burst. Do not install the washing machine in an area where

there is a risk of frost or outdoors.

 Do not hold onto protruding parts (e.g. loading door) when lifting. Washing machine may

be damaged.

 Before transporting the appliance, always drain dispensers. aPage 8

 In addition to the safety information listed here, the local water and electricity supplier may

have special requirements.

 If in doubt, have the appliance connected by a technician.

 Lay hoses and cables in such a way that there is no risk of stumbling.

Environmental disposal

  Dispose of packaging in an environmentally friendly manner.

 This appliance has been identified in accordance with the European Directive 2002/96/EG

on Waste Electrical and Electronic Equipment (WEEE).

The Directive specifies the framework for an EU-wide valid return and recycling of waste

appliances.

Installation area

 Stability is important to prevent the machine from moving!

 The installation area must be firm and level.

 Soft floors/floor coverings are not suitable.

If installing the appliance on a base

 secure the washing machine feet with retention plates *.Always

* Order no. WMZ 2200, WX 9756, CZ 110600, Z 7080X0

If installing the appliance on a wooden joist ceiling

 If possible, install the washing machine in a corner.

 Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.

 secure the washing machine feet with retention plates.Always

* Order no. see above

Installation on a platform with drawer*

* Order no. WMZ20490, WZ20490

Built-under/Built-in appliance

Build-under/Build-in before connection to the power supply.

Installed in between kitchen units (built-under or built-in)

 60 cm cavity width required.

 Install washing machine only under a continuous worktop connected firmly to the adjacent

cupboards.

Built-under

Risk of electric shock!

 Instead of the appliance cover panel, it is to have a technician fit a sheet metal essential

cover *. * Order no. WMZ 2043, WZ 20430

 60 cm cavity width required.

Scope of delivery depending on model

not included in product package:

When drainage is into a siphon, a Ø 2440 mm hose clip (specialist outlet) is also required.

a Water connection, Page 4

Useful tools:

 Spirit level for aligning the washing machine.

 Size 13 socket wrench:

for loosening the transportation protection devices and aPage 3

size 17: for aligning the appliance feet. aPage 5

Hose and cable lengths depending on model

Connection on left side or Connection on right side

Note: If the hose holders are used, the possible hose lengths are reduced!

Available from dealer/customer service:

 Extension for Aqua-Stop or cold water inlet hose (approx. 2.50 m).

Order no. WMZ2380, WZ10130, CZ11350, Z7070X0

 Longer supply hose (approx. 2.20 m), for standard model.

Spanner

(depending on model)

Power cord

Water supply

Water drainage

Elbow

for securing the

drainage hose

Covers

Aqua Stop Aqua-Secure

~140 cm

~95 cm

~120 cm

~130 cm

~100 cm

~135 cm

0  max. 100 cm

Humidity in the drum

is caused by the final

inspection.

Produktspezifikationen

Marke:	Siemens
Kategorie:	Waschmaschine
Modell:	WM16S890EU

Brauchst du Hilfe?

Wenn Sie Hilfe mit Siemens WM16S890EU benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Waschmaschine Siemens

Siemens WG44G20B Bedienungsanleitung

8 Oktober 2024

Siemens WG56B2AC Bedienungsanleitung

8 Oktober 2024

Siemens WU14UT61ES Bedienungsanleitung

3 Oktober 2024

Siemens WM10Q32XEE Bedienungsanleitung

29 September 2024

Siemens WM12B260EE Bedienungsanleitung

18 September 2024

Siemens WD14U592 Bedienungsanleitung

17 September 2024

Siemens WM12Y749IT Bedienungsanleitung

17 September 2024

Siemens WM12Q390GB Bedienungsanleitung

16 September 2024

Siemens WM14E474FG Bedienungsanleitung

13 September 2024

Siemens WM16S743NL Bedienungsanleitung

11 September 2024

Bedienungsanleitung Waschmaschine

Neueste Bedienungsanleitung für -Kategorien-

Candy CS 15102D3-80 Bedienungsanleitung

16 Oktober 2024

GE GSD3715FAA Bedienungsanleitung

16 Oktober 2024

Freggia WTIE148 Bedienungsanleitung

16 Oktober 2024

Freggia WISE126R Bedienungsanleitung

16 Oktober 2024

Freggia WISE126B Bedienungsanleitung

16 Oktober 2024

Freggia WISE126 Bedienungsanleitung

16 Oktober 2024

Freggia WISA105 Bedienungsanleitung

16 Oktober 2024

Freggia WISA106 Bedienungsanleitung

16 Oktober 2024

Freggia WIA107 Bedienungsanleitung

16 Oktober 2024

Freggia WDIE14106 Bedienungsanleitung

16 Oktober 2024