Siemens HB86P672B Bedienungsanleitung

Siemens Ofen HB86P672B

Lesen Sie kostenlos die πŸ“– deutsche Bedienungsanleitung fΓΌr Siemens HB86P672B (3 Seiten) in der Kategorie Ofen. Dieser Bedienungsanleitung war fΓΌr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
*9000664521* 9000664521 940407
Ú Installation instructions
ξ€”
PLQ
ξ€˜ξ€˜ξ€“
ξ€˜ξ€™ξ€“ξ€ƒ
ξ€Žξ€”ξ€—

ξ€—ξ€˜ξ€›ξ€ƒ
ξ€Žξ€•
ξ€—ξ€˜ξ€“
ξ€˜ξ€—ξ€› ξ€˜ξ€œξ€˜

ξ€—ξ€˜

ξ€—ξ€˜
ξ€—ξ€˜

PLQ
ξ€˜ξ€˜ξ€“
PLQ
ξ€˜ξ€˜ξ€“
ξ€—ξ€˜
ξ€˜ξ€™ξ€“ξ€ƒ
ξ€Žξ€”ξ€—
ξ€˜ξ€™ξ€“ξ€ƒ
ξ€Žξ€”ξ€—
ξ€—ξ€˜ξ€“ξ€ƒ
ξ€Žξ€•
ξ€—ξ€˜ξ€“ξ€ƒ
ξ€Žξ€•
PLQξ€‘ξ€ƒξ€œξ€“
PLQξ€‘ξ€ƒξ€—ξ€˜
(
'
ξ€–
ξ€—
ξ€—
ξ€—
ξ€—
ξ€—
FOLFN
PD[
ξ€”ξ€™
PD[
ξ€”ξ€™
PD[
ξ€”ξ€™
 ξ€”ξ€˜ξ€ξ€”ξ€š 
ξ€˜
ξ€˜
ξ€˜
ξ€˜
ξ€˜
PLQξ€‘ξ€ƒξ€˜
en
Ú Installation instructions
The following must be noted:
Electrical connection
The appliance is fitted with a plug and must only be connected
to a properly installed earthed socket. Only a qualified
electrician who takes the appropriate regulations into account
may install the socket or replace the connecting cable.
If the plug is no longer accessible following installation, an all-
pole isolating switch must be present on the installation side
with a contact gap of at least 3 mm.
Contact protection must be ensured by the installation.
United Kingdom and Australia
The appliance is designed for a permanent connection to a 3-
wire circuit. The appliance must only be connected by a
qualified electrician in accordance with the wiring diagram
attached to the connecting cable.
An all pole disconnecting device must be present on the 
installation side with a contact gap of at least 3 mm in order to
comply with current safety regulations.
The appliance fulfils the requirements of protection class Y, in
accordance with heating test standards. The colours of the wires
in the mains cable correspond to the following coding: green/
yellow = PE conductor, blue = neutral conductor, brown = phase.
Do not connect the appliance using a 13 A plug or protect with
a 13 A fuse.
Fitted units
The fitted cabinet must not have a back wall behind the
appliance. A gap of at least 45 mm must be maintained
between the wall and the cabinet base and/or the back panel of
the overlying cabinet.
The fitted cabinet must have a ventilation opening of 50 cmΒ² on
the front. For surround units with no ventilation cut-out in the
back of the side panels 200 cmΒ². To do this, cut back the base
panel or fit a ventilation grille.
Make sure that you do not cover ventilation slots and air inlet
openings.
The safe operation of this appliance can only be guaranteed if it
has been installed to a professional standard in accordance
with these installation instructions. The installer is liable for
damage incurred as a result of incorrect installation.
Fitted units must be heat-resistant up to 90 Β°C, and
neighbouring unit fronts up to at least 70 Β°C.
Cut-out work on the units and worktop should be performed
before fitting the appliances. Remove any shavings or the
function of the electrical components may be impaired.
Appliance under the worktop - Fig. 1
There must be a ventilation cut-out made in the intermediate
floor of the surround unit.
Secure the worktop to the fitted units.
If a fitted oven is to be built in under a hob, pay attention to the
hob installation instructions.
Appliance in a tall unit - Fig. 2
The appliance may only be fitted above a ventilated oven from
the same manufacturer.
Installation above a refrigerator is possible.
The appliance must not be fitted above a steamer, combination
steam oven or a dishwasher.
Corner installation Fig. 3
For corner installation, dimension must be taken into D
consideration. Dimension is dependent on the thickness of E
the unit front and the handle.
Preparing for installation  Figs 4
If necessary, fit the spacer - Fig. 4.
Securing the appliance  Fig. 5
β– Fully insert the appliance and centre it.
β– Do not kink the connecting cable.
β– Screw the appliance into place.
β– The gap between the worktop and the appliance must not be
closed by additional battens.
Removal
Disconnect the appliance from the power supply. Undo the
securing screws. Raise the appliance slightly and pull it out
completely.


Produktspezifikationen

Marke: Siemens
Kategorie: Ofen
Modell: HB86P672B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Siemens HB86P672B benΓΆtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Ofen Siemens

Bedienungsanleitung Ofen

Neueste Bedienungsanleitung fΓΌr -Kategorien-