SereneLife SLCATL420 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SereneLife SLCATL420 (4 Seiten) in der Kategorie Hochdruckreiniger. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
www.SereneLifeHome.com
MAIN FEATURES
COMPONENTS
Premium user comfort: Full size & soft-close seat
and lid, large toilet bowl and 478mm seat height
brings greater homelike performance.
Easy to ush: High gloss toilet bowl with original
T type 3 way ush ow creates high-speed, full bowl
ushing.
Ergonomically enhanced pedal operation:
Lower pedal height for easier use.
One-direction action to open drain valve and ush.
Easy installation: Two bolts design ts most existing
toilet oor anges, great for new or replacement
installation. Just place on oor ange, tighten bolts,
connect water, and its ready.
FLOOR MOUNTING KIT
Flange plate Seal ring T-bolt and
rubber case
www.SereneLifeHome.com
PRODUCT AND MOUNTING DIMENSION
The outside diameter of the toilet drain outlet: 95mm / 3.7”;
The inner diameter of the toilet drain outlet: 87mm / 3.4”
INSTALLATION
Note:
Be sure foot pedal, when pressed, touches same at surface on which toilet is installed.
Ensure water supply pressure is no more than 0.4Mpa.
Hot water more than 40 degrees is forbidden.
1. To replace an older toilet, turn o water supply to toilet. Remove and drain water supply line.
Remove toilet hold-down bolts/screws. Remove toilet from oor. Remove and discard old ange seal
and hold-down bolts. Verify center of oor ange is at least 200mm/7.9” from back wall ( ).Fig.1
2. If installing a new oor ange, make certain that toilet mounting holes are located at the correct angle
(Fig.1). Floor ange must be secured to oor with a minimum of four screws. Insert two supplied T-bolts
into slots in oor ange (Fig.2).
3. Verify that oor ange seal is installed on base of toilet. Carefully set toilet over oor ange.
Align holes in toilet base with T-bolts as toilet is lowered onto oor ange.
4. Install oor mounting nuts onto T-bolts. When tight, base should be securely attached and at against
oor. Attach bolt covers onto nuts
5. Connect water supply line to ½ inch water inlet and turn on water supply line. (Fig.3)
Flush toilet several times and check for leaks.
A
B
C
D
E
F
G
HI
J
www.SereneLifeHome.com
OPERATION
Back wall
left wall
right wall
G
200mm
H
200mm
I
200mm
Fig.1
Sealing ring
Water Inlet
Pipe Connector
Fig.3
Strainer
Fig.2
Before connecting your pipe connector
(plastic one is recommended) to the ½ inch water
inlet (1/4-20 British thread), make sure there is a
sealing ring in the pipe connector.
If not, the attached sealing ring must be placed to
ensure perfect sealing.
After connecting water supply, ush the toilet
several times to check leaks.
Fig. 4
Fig. 5
1. Add water to bowl
To add water to the toilet, press the ush pedal part way down.
Water ows into the bowl while ush valve remains closed.
If the ush valve moves, let up on the pedal slightly.
Adding water to an empty bowl helps prevent holding tank odors
from entering the living space. Adding water is recommended
prior to ushing solids and toilet paper. (Fig.4)
2. Flush toilet
To ush, press pedal down until it contacts the oor.
Release pedal after complete ush. (Fig.5) When ushing liquids,
press the pedal for 1-2 seconds. When ushing solids, press pedal
until contents are rinsed from bowl.
Flushing longer than necessary will cause holding tank to ll too
quickly. A small amount of water will collect in the bowl after a
ush t create an airtight seal.


Produktspezifikationen

Marke: SereneLife
Kategorie: Hochdruckreiniger
Modell: SLCATL420

Brauchst du Hilfe?

Wenn Sie Hilfe mit SereneLife SLCATL420 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Hochdruckreiniger SereneLife

Bedienungsanleitung Hochdruckreiniger

Neueste Bedienungsanleitung für -Kategorien-