Seiko S141 Bedienungsanleitung

Seiko betrachten S141

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Seiko S141 (5 Seiten) in der Kategorie betrachten. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/5

NOTES ON THE BATTERY FOR THE STOPWATCH

Do not remove the battery from the watch.

If it is necessary to take out the battery, keep it out of the reach of children. If a child swallows it, consult a doctor

immediately.

Never short-circuit, heat or otherwise tamper with the battery, and never expose it to fire. The battery may burst,

become very hot or catch fire.

The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the

battery.

WARNING

NOTES ON THE STRAP

The stopwatch has a strap for wearing it around your neck. Take good care lest it should be caught by something

near you or wind around your neck.

Please also note that the strap may damage your clothes, or injure your hands, neck or other parts of your body.

You are now the proud owner of a SEIKO Digital Stopwatch Cal. S141. For best results, please read the instructions

in this booklet carefully before using your SEIKO Digital Stopwatch. Please keep this manual handy for ready reference.

SEIKO DIGITAL STOPWATCH Cal. S141

TO PRESERVE THE QUALITY OF YOUR STOPWATCH

WATER RESISTANCE (10 bar)

Your stopwatch is designed and manufactured to

withstand up to 10 bar, and is suitable for taking baths

and shallow diving, but not for scuba diving.

Do not operate the buttons when the stopwatch is wet or

in water. If used in sea water, rinse the stopwatch in

fresh water and dry it completely.

When bathing with your stopwatch, be sure to observe

the following:

* Do not operate the buttons when the stopwatch is wet

with soapy water or shampoo.

* If the stopwatch is left in warm water, a slight time loss

or gain may be caused. This condition, however, will

be corrected when the stopwatch returns to normal

temperature.

TEMPERATURES

If the stopwatch is left in direct sunlight for a long time,

the display may become black, but this condition will be

correc ted when the sto pwatch return s to normal

temperature. Do not leave your stopwatch in very low

temperatures below –10 C (+14 F) for a long time since

the cold may cause:

a. a slight time loss or gain.

b. the change of digits to become slow.

c. the display light to dim.

However, the above conditions will be corrected when

the stopwatch returns to normal temperature.

SHOCKS

Do not subject it to violent shocks.

MAGNETISM

Your stopwatch will not be affected by magnetism.

CHEMICALS

Be careful not to expose the stopwatch to solvents,

mercury, cosmetic spray, detergents, adhesives or paints.

Otherwise, the case, etc. may become discolored,

deteriorated or damaged.

PERIODIC CHECK

It is recommended that the stopwatch be checked once

every 2 to 3 years. Have your stopwatch checked by an

AUTHORIZED SEIKO DEALER or SERVICE CENTER to ensure

that the case, buttons, gasket and crystal seal remain intact.

PRECAUTION REGARDING CASE BACK PROTECTIVE FILM

If your stopwatch has a protective film and/or a sticker on

the case back, be sure to peel them off before using it.

STATIC ELECTRICITY

The IC (Integrated Circuit) used in your stopwatch will be

affected by static electricity which may disturb the display.

Keep your stopwatch away from close contact with objects

such as TV screens which emit strong static electricity.

LIQUID CRYSTAL PANEL

The normal life expectancy for a liquid crystal panel is

approximately 7 years. After that it may decrease in

contrast, becoming difficult to read. Please contact your

AUTHORIZED SEIKO DEALER or SERVICE CENTER if you

wish to have a new panel fitted (guaranteed one year).

o o

SEIKO Cal. S141 is a digital stopwatch featuring memory and stroke/frequency measuring functions. In

addition, it is water resistant and withstands up to 10 bar. Therefore, it is suitable for aquatic sports or

use in rainy weather.

STOPWATCH

The stopwatch can measure up to 10 hours in 1/100 second.

SPLIT TIME/LAP TIME MEASUREMENT

Up to 300 split times and lap times can be measured.

LARGE-SIZED THREE-ROW DISPLAY PANEL

Total elapsed time/lap time in progress, split time and lap time are displayed at the same time in separate

rows, and they can be measured successively without releasing split or lap time measurement.

STROKE/FREQUENCY MEASURING FUNCTION

The stroke/frequency of an activity per minute is automatically calculated only by measuring the time

required to make three strokes. Up to 9 data can be stored in memory.

DUAL MEMORY MODE

Single memory mode ..... Up to 300 lap/split time data can be stored and recalled either during or after

measurement.

Block memory mode ...... A sequence of measurement data obtained from race start to finish is recorded

as a “block.” Up to 100 blocks of data can be stored in memory without deleting

the previous data.

Memory capacity indicator and fastest lap time recall functions are also provided. Even if the stopwatch

is reset, the times stored in memory will not be erased and can be recalled as desired.

ID NO. FUNCTION

Besides the time and calendar, identification numbers can be set. It is useful for keeping the data of

individual users separately.

ANTIBACTERIAL CASE

An antibacterial agent is applied to the case surface of the stopwatch.

* It loses its antibacterial effect gradually over time and the effective period differs depending on the conditions of use.

FEATURES

CHANGEOVER OF DISPLAYS

With each press of “D,” the display changes

in the following order.



STOPWATCH 1

(Accumulated elapsed time)

display

STOPWATCH 2

(Lap time in progress)

display

TIME/

CALENDAR

display



STROKE/

FREQUENCY

MEASURING

display



TIME/CALENDAR SETTING

3. Press “A” to set the digits. The digits move quickly if the button is kept pressed.

4. Press “B” to return to the TIME/CALENDAR display.

Before setting the time/calendar or ID No., be sure to reset the stopwatch to “00.” The time/calendar and ID No. can be set only when the stopwatch is reset.

1. Press “D” to show the TIME/CALENDAR display, and then press “B.” SECOND digits flash. Press “A” to reset the SECOND to “00.”

2. Press “B” repeatedly to select the digits (flashing) to be adjusted in the following order.

Hour

ID No.

TIME/CALENDAR display indicator

Month Year

Date

Seconds

Minutes

Notes:

1. The calendar automatically adjusts for odd and even months including February of leap years from 2006 to 2055.

2. When the SECOND reads any number from “30” to “59” and “A” is pressed, one minute is added.

3. The time is displayed in the 24-hour indication.

4. The ID No. can be set in two digits from “01” to “99”. When “OFF” is displayed, it indicates that no ID No. is set.

TIME/CALENDAR display SECOND MINUTE HOUR YEAR MONTH DATE ID NO. MEMORY MODE

Setting mode

ADJUSTING THE CONTRAST ON THE DISPLAY

The contrast of the liquid crystal display can be adjusted in 10 steps from level “1” to “10.”

1. Press “C” in the TIME/CALENDAR display to show the CONTRAST ADJUSTMENT display.

2. Press “A” or “B” repeatedly to adjust the contrast. The display becomes darker by pressing “A”

and lighter by pressing “B.”

3. Press “C” or “D” to return to the TIME/CALENDAR display.

Contrast

level

Block memory mode Single memory mode

BLOCK mark Change of memory mode will delete all the

previously stored data.

CAUTION

5. To change the memory mode, press and hold "A" for 1.5 seconds.

When "OFF" is displayed above "BLOCK," the stopwatch is in the single memory mode, which is the default setting.

When "ON" is displayed above "BLOCK" and the BLOCK mark appears at the bottom right, the stopwatch is in the block memory mode, which is designed for

professional level use.

 Refer to MEMORY RECALL FUNCTION---BLOCK MEMORY MODE on page 3.

STOPWATCH

Before using the stopwatch, be sure to reset the digits to “00.”

When the stopwatch is stopped, press “B.”

When the stopwatch is counting, press “A” and then press “B.”

1. STANDARD MEASUREMENT

A BA

START STOP RESET



2. ACCUMULATED ELAPSED TIME MEASUREMENT

A AA

START STOP RESTART

STOP

RESET



* Restarting and stopping the stopwatch can be repeated by pressing “A.”

Press “D” to show the STOPWATCH 1 (Accumulated elapsed time) display.

• Up to 300 lap/split time data can be stored in memory and recalled during or after measurement.

• The stopwatch can measure and display the lap/split time that exceeds its limit of 300, but it cannot store the data in memory for the 301st measurement

data and afterward.

* When a new measurement is commenced while the stopwatch is in the single memory mode, the lap/split time data obtained from the previous measurement will be automatically deleted.

• For professional level use, the default single memory mode can be changed to the block memory mode, in which commencement of a new measurement

will not erase the previous measurement data. The block memory mode is useful for saving records or comparing data.

Refer to MEMORY RECALL FUNCTION---BLOCK MEMORY MODE on page 3.

Block No.

Lap time

Split time

AB C

STOPWATCH display indicator

Accumulated elapsed time /

lap time in progress

Notes:

1. When the digits are reset to “00” by pressing “B,” a new block number for the next measurement is displayed.

2. In the lap time in progress display, when the lap time measurement in progress exceeds 1 hour, the hour digit appears in place of the mark for lap time in progress display.

B BA

START

STOP

RESET



SPLIT/LAP 1 SPLIT/LAP 2

* The split/lap time can be measured repeatedly by pressing “B.”

Accumulated elapsed

time display

Lap time in progress

display

Split/lap No.

Split time

Lap time

Accumulated elapsed time Lap time in progress

Lap time in progress

display mark

Press “D” to show the STOPWATCH 1 (Accumulated elapsed time) display or STOPWATCH 2 (Lap

time in progress) display.

3. SPLIT/LAP TIME MEASUREMENT

“Split time” refers to an elapsed time required to

cover a distance from the start to a given point.

“Lap time” refers to an elapsed time required to

cover a given section of the whole distance.

Start

Lap time

Split time

• Up to 300 lap/split time data of one measurement can be stored in memory and recalled on display.

• With each press of “C,” the stored data is recalled. The data can be recalled successively one after another by keeping “C” pressed.

• The stored data can be recalled even during measurement (while the stopwatch is measuring).

• Memory recall sequence

When the stopwatch is stopped, with each press of “C,” the stored data will be recalled from the first (oldest) to the last (newest) data.

When the stopwatch is measuring, with each press of “C,” the stored data will be recalled from the last (newest) to the first (oldest).

MEMORY RECALL FUNCTION ------- SINGLE MEMORY MODE

* The data can be recalled successively by keeping “C” pressed.

* To stop the recall of the data when the stopwatch is stopped, press “A”, “B” or “D.”

To stop the recall of the data when the stopwatch is reset, press “A” or “D.”

With each press of “C,” the data is recalled chronologically (starting from the first/oldest data).

Ex.: When the stopwatch is reset to “00” after the measurement

Reset First lap time Split & lap times Stop time

MEMORY RECALL WHEN THE STOPWATCH IS STOPPED OR RESET

RECALL mark appears while the stored data is being recalled on display.

The mark shows the memory recall sequence (descending/ascending).

Lap/Split

number

Split time Lap time

• When a new measurement is

commenced, the lap/split time data

obt a ined from the pre vi ou s

measurement will be automatically

deleted.

MEMORY RECALL FUNCTION ------- BLOCK MEMORY MODE

The Cal. 141 features a dual memory mode:

Single memory mode ..... The single memory mode is the default-set mode. The lap/split time data of one measurement from start to stop can be stored.

When the stopwatch is reset, and a new measurement is commenced, the lap/split time data of the previous measurement will

be automatically deleted.

Block memory mode ...... The block memory mode is an advanced mode designed for professional level use. A sequence of measurement data obtained

from start to stop (or reset) is recorded as a “block.” Up to 100 blocks of data can be stored in memory without deleting the

previous data.

1. While in the TIME/CALENDAR display, press “B” 8 times until “BLOCK” appears on the display, above which either “ON” or “OFF” is flashing.

2. Press “A” for 1.5 seconds until the memory mode changes with a long beep.

Benefits of block memory mode

Easy data management ............ The block number as well as starting time and date of measurement are automatically recorded and stored.

Handy data storage ................ Creation of a new block of data will not erase the previous data in memory. While in the single memory mode,

a new measurement will delete the latest measurement data.

Block mark*

* When the block memory mode is selected, the BLOCK

mark appears at the bottom right on the display regardless

of the display mode.

A A

Single memory mode Block memory mode

Produktspezifikationen

Marke:	Seiko
Kategorie:	betrachten
Modell:	S141

Brauchst du Hilfe?

Wenn Sie Hilfe mit Seiko S141 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung betrachten Seiko

Seiko 6N76 Bedienungsanleitung

6 September 2024

Seiko 6N53 Bedienungsanleitung

6 September 2024

Seiko 6N52 Bedienungsanleitung

6 September 2024

Seiko 6G28 Bedienungsanleitung

6 September 2024

Seiko 4N30 Bedienungsanleitung

6 September 2024

Seiko 4227 Bedienungsanleitung

6 September 2024

Seiko 6N32 Bedienungsanleitung

6 September 2024

Seiko 6N42 Bedienungsanleitung

6 September 2024

Seiko 6N22 Bedienungsanleitung

6 September 2024

Seiko 1N01 Bedienungsanleitung

6 September 2024

Bedienungsanleitung betrachten

Neueste Bedienungsanleitung für -Kategorien-

Casio GW-3000BD-1AER Bedienungsanleitung

9 Oktober 2024

Citizen Cal 411X Bedienungsanleitung

7 Oktober 2024

Casio Edifice EFA-112D-1AVEF Bedienungsanleitung

7 Oktober 2024

Casio Baby-G BGA-200-1E2ER Bedienungsanleitung

6 Oktober 2024

Jaguar J627 Bedienungsanleitung

6 Oktober 2024

Citizen CAL 4633 Bedienungsanleitung

5 Oktober 2024

Auriol IAN 277495 Bedienungsanleitung

4 Oktober 2024

La Crosse Technology WT-941 Bedienungsanleitung

4 Oktober 2024

Spin Master Dumas SP-5081-11 Bedienungsanleitung

4 Oktober 2024

Michael Kors Kors Access Scout Hutton MKT4024 Bedienungsanleitung

3 Oktober 2024