Sedona S42CART Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sedona S42CART (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
Assembly Instructions:
SEDONA L400CART
L500CART
& L600CART
Sedona Freestanding Cart
Model L400CART, L500CART &L600CART
Lynx Grills, Inc., 6023 E. Bandini Blvd. Commerce, CA 90040 Ph
Document 33807 Rev C 02/08/13
Step 1.
Step 2.
Step 3.
Step 1.
Aer opening and idenfying the components, select the back
panel assembly and either the right or le side panel assembly.
Orient the parts as shown in the illustraon for . step 1
Note that these parts are upside down with the shelves at the
oor. Hook the right or le side to the back into the four keyways
located on the edge. When aached all four keyways should be
engaged and the back and side ush to the top.
Repeat this step for the opposite side panel.
Step 2.
With the cart oriented upside down, locate the 4 - #8 screws and
nuts and mount the electrical transformer to the access plate
shown in the illustraon for this step. It may be done at the end of
the assembly but is somewhat easier to access at this stage.
Step 3.
Refer to the gure for and insert the base assembly into the step 3
cavity at the back corners of the cabinet. Check that the tank hole
is posioned as shown and the magnet is located on the open side.
Splay the two sides out slightly and enclose them over the front of
the base. The sides and back have pockets that t over the casters
for clearance. Use 4 of the ¼-20 x ½ screw at each corner to lock
the assembly in place.
Access
Plate
magnet
tank
hole
Screw
4 places
Introducon:
Your Freestanding Cart comes with all of the components necessary
to assemble a cart for the SEDONA Series of Lynx Grills.
The SEDONA CART series is comprised of 8 sub assemblies:
1. Back Panel Assembly
2. Right Side Panel Assembly with Shelf
3. Le Side Panel Assembly with Shelf
4. Base Assembly with Wheels
5. Inner Shelf Assembly
6. Cross Brace Assembly
7. Right Door
8. Le Door
In addion there are 14 screws (1/4 -20 x ½) to assemble the
cart and grill and 4 screws with nuts (#8-32 x 3/8) to aach the
transformer assembly supplied with the Grill.
TM
Step 4.
Step 5.
To begin turn the cabinet upright to secure the step 4
Inner Shelf Assembly. The and shelf will only L400 L500
assemble as shown at the right with the electrical hole to
the rear and the screws mounng at the back and le
side. The shelf is not only useful but necessary for the
proper stability of the cart. omit the inner shelf DO NOT
or any part in these instrucons.
The inner shelf is secured by 4 of the ¼-20 x ½ screws.
Two through the back and two through the le side.
The shelf as shown here will assemble L600
the same as above.
Step 5 L400/L500 is the last assembly on the cart before
installing the Grill to the cart. The cross brace ts into
recesses located at the front edge of the cart above the
hinge brackets. Orient the brace with the center magnet
facing forward and posioned such that the magnet is
higher than center rather than lower. Install the brace from
the backside of the anges and align the nutcerts at each
end with the holes provided for the screws. The brace is
secured by 2 of the ¼-20 x ½ screws.
The door frame is aached along with the cross brace . L600
Support the cross brace from the backside of the front
anges. Align the nutcerts at each end with the holes
provided for the screws. Posion the door frame over the
nutcerts and cross brace , and secure them both with the ¼-
20 x ½ screws.
Step 4 .
L400
L500
Step 4 .
L600
Step 5.
L400
L500
Step 5.
L600
With assistance, remove all packing materials from the grill.
Also remove the grates and warming racks to lighten the
assembly. The grill will be placed onto the cart as
illustrated in this step. The back edge will engage rst and
the front will slide down into posion unl horizontal.
Using at least two people with gloves - grasp the front
and side of the Grill at points A and B. Place the unit on the
cart and lower it slowly unl horizontal.
You may need to loosen the Screws
inside the rebox. (See Step 7)
Do not grip grill by the
control knobs as damage
may occur
Step 6.
Four screws remain in the package for assembly.
To secure the grill to the cart locate 4 screws at the in
corners of the rebox. Remove and discard the 4 scre
these locaons. Replace them one at a me with the
screws from the kit.
Refer to the installaon manual provided with the gri
proper electrical and gas connecons.
B
A
Step 7.
2
4
1
3
Drop the door hinge
pins into the
corresponding door
hinge on the frame.
Step 6.
Step 7.


Produktspezifikationen

Marke: Sedona
Kategorie: Nicht kategorisiert
Modell: S42CART

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sedona S42CART benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Sedona

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-