Scosche GM1488B Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Scosche GM1488B (2 Seiten) in der Kategorie Auto Kit. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
IN-DASH INSTALLATION KIT FOR
1988-03 FULL SIZE PICKUP/SPORT UTILITY
© 2007 SCOSCHE INDUSTRIES, INC.
If you have any further questions, call
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire
harness/codes and information pertaining to installation of this kit (GM1488) in 1988-03 General Motors Vehicles.
Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the
automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of
components while using this booklet.
SI 12/06 - GM1488 (3000317)
TECH HELP 1-800-621-3695 x 3
GM1488
CADILLAC
1999-02 ESCALADE
2002-02 ESCALADE EXR
CHEVROLET
1996-02 ASTRO VAN
2001-02 AVALANCHE
1992-94 BLAZER FULL SIZE
1992-99 CREW CAB / DOOLEY PICKUP
1996-00 EXPRESS VAN
1988-02 PICKUP FULL SIZE
1992-02 SUBURBAN
1995-02 TAHOE
GMC
1992-00 CREW CAB / DOOLEY PICKUP
1988-02 PICKUP FULL SIZE
1996-03 SAFARI
1996-00 SAVANNA
1992-02 SUBURBAN
1992-02 YUKON
1999-99 YUKON DENALI
2000-02 YUKON XL
#2006
MOUNTING
PANEL
#2224R
MOUNTING
CLIP (RIGHT)
#2224L
MOUNTING CLIP
(LEFT)
#1869/2543
MOUNTING
PANEL
HEX NUT
CARRIAGE
BOLT
1996-02 Chevrolet Astro Van
1996-03 GMC Safari Van
RADIO REMOVAL:
1. Extract (2) T-30 torx bolts, one from each side of the top console area and pop out top half of center
console assembly.
2. Extract (2) 9/32" hex screws from the bottom edge of the driver’s side under dash panel and (1) screw
from left dash below defroster vent.
3. Carefully pry underdash panel out to release, and use caution when handling parking brake release cable.
4. Insert key into "on", adjust shifter down (low gear), Pull outward on the instrument/radio panel to release
clips. Unplug switches, and remove panel.
5. Push down on side tabs securing radio, slide out of dash, unplug, and remove radio.
4
1996-00 Chevrolet Express Van
1996-00 GMC Savanna
RADIO REMOVAL:
1. Carefully pull out on dash instrument/radio dash bezel to release spring clips, unplug connectors and
remove panel.
2. Compress the two plastic side radio mounting clips, slide radio out of dash, unplug connectors and remove
radio.
INTRODUCTION / PRELIMINARY
This premium installation kit is for 1988-03 Full Size Pickup/Sport Utility vehicles. Included are all the parts
you need to mount your car stereo/cassette or CD player into your vehicle's dash. Refer to the individual
instruction in this manual to remove your vehicle's factory radio and assemble the kit.
CAUTION:
DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP
PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER OVER A TEST LIGHT TO
CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S
COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIRBAG WIRING - AIRBAGS CAN
ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH.
NOTES:
• See your vehicle's instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
CAR STEREO CONNECTORS
PROVIDE EASY CONNECTION OF YOUR CAR
STEREO TO FACTORY WIRING HARNESS.
GM02B
1988-Up
FACTORY WIRING CODES
GM02B
MDA-1B
Antenna Adaptor
MDA-1B
1992-94 Chevrolet Blazer
1992-99 Chevrolet Crewcab Dually
1992-00 GMC Crewcab Dually
1988-02 Chevrolet / GMC
Full Size Pickup
1992-02 Chevrolet / GMC Suburban
3
1999-02 Cadillac Escalade
2002-02 Cadillac Escalade EXT
2001-02 Chevrolet Avalanche
1995-99 Chevrolet Crewcab /
Dually Pickup
RADIO REMOVAL:
1. Engage parking brake.
2. Place key in ignition and depress brake to shift vehicle in to lowest gear.
This will allow the gear shift arm to be out of the way.
3. Carefully pull out on dash instrument/radio dash bezel to release
spring clips, unplug connectors and remove panel.
4. Compress the two plastic side radio mounting clips, slide
radio out of dash, unplug connectors and remove
radio.
NOTE: Use caution when removing the dash bezel over
the hazard switch. The hazard switch may need to be
pushed down as if to activate the hazard lights to allow
the bezel to slide over it.
NOTE (2): It is recommended that you use the Scosche GM02
factory connector and the MDA-1 antenna adapter to eliminate
the need to cut any of the factory plugs.
STEREO INSTALLATION/KIT PREPARATION:
Panel #2006 panel preparation:
1. Remove the metal fastening clips from the bottom
of the factory dash bezel and attach them to the
same location on the #2006 panel. (See
Illustration B)
2. Remove the A/C vents from the factory dash
bezel by releasing the spring fastening clips
securing them into the bezel.
3. Mount the vents into the kit by inserting the inner
edge of the vent into the center inside pivot hole.
Then insert the outer edge of the vent into the
outer pivot hole. Using the same metal spring
clips and mounting procedures from the original
truck panel to mount the vents to the new
#2006 panel.
STEREO INSTALLATION WITH THE 2006 PANEL:
1. Install the 2006 panel into the dash by inserting
the top mounting clips into the slots in the dash
and pushing up to snap them in. Then press the
bottom clips into the slots at the bottom of the
dash to secure the kit to the dash.
2. See illustration C for stereo mounting
configurations.
STEREO INSTALLATION WITH THE 1869/2543 PANEL
1. Attach the left and right side brackets to the
mounting panel with the carriage bolts
and nuts provided.
2. See illustration D for stereo mounting
configurations.
#1869/2543
MOUNTING PANEL
SHAFT RADIO'S
SUPPLIED FACEPLATE
RADIO'S SUPPLIED
TRIMPLATE
SHAFT RADIO
SNAP SHAFT TABS:
(SEE NOTE)
#2224R
MOUNTING
CLIP
#2224L
MOUNTING
CLIP
RADIO'S REAR
SUPPORT STRAP
STEREO INSTALLATION/KIT PREPARATION
2
ILLUSTRATION D
DIN
STEREO
RADIO'S REAR
SUPPORT STRAP
#1869 / 2543
MOUNTING
PANEL
RADIO'S
MOUNTING
SLEEVE
RADIO'S SUPPLIED
TRIMPLATE
BEND
TABS
OUT-
WARD
RADIO'S
SUPPLIED
TRIMPLATE
#2006
MOUNTING
PANEL
RADIO'S
MOUNTING
SLEEVE
DIN
STEREO
BEND
TABS
OUT-
WARD
ILLUSTRATION C
ILLUSTRATION B
REAR
VIEW
OF KIT
METAL
FASTENING
CLIP
DASH BEZEL/TUNER PACK REMOVAL:
1. Carefully remove the factory tape/EQ (or pocket) bezel by prying out along the
bottom to release fastening clips. Then carefully pull down on the bezel to
release the fasteners securing the top and remove the bezel.
2. Extract the two (2) screws securing the factory tape player/equalizer (when
equipped).
3. Remove the dash panel under the steering column by extracting the
two (2) screws securing it to the dash.
4. Locate the radio tuner pack (metal control box) under the
dash above the accelerator pedal. Remove it by extracting
the three (3) screws securing it to the underdash brackets.
5. Unplug all the connectors going into the radio tuner pack and
remove it from the vehicle.
6. Pull the tape player/equalizer from the dash and carefully pull
the plug harness through the dash from the radio tuner pack
location and remove the tape player/equalizer form the dash.
7. Locate the antenna plug and the plugs that were connected to the top of the radio tuner pack. Route them
into the tape player/equalizer cavity. These are the factory power, speaker and antenna plugs that will be
used for the aftermarket radio hook-ups.
NOTE: It is recommended that you use the Scosche GM02 factory connector and the MDA-1 antenna
adapter to eliminate the need to cut any of the factory plugs.
OPTIONAL FACTORY RADIO DISPLAY/CONTROL UNIT REMOVAL AND POCKET REPLACEMENT:
1. Extract the (4) screws securing the instrument cluster dash bezel to the dash.
2. Pull the dash bezel from the dash, disconnect all the connectors and remove the bezel.
3. Extract the (4) screws securing the heater controls to the dash and pull it out of the dash cavity.
4. Extract the (4) screws securing the radio to the dash and pull from the cavity.
5. Route the radio leads from the tuner location as mentioned in step 4 of tape player/equalizer removal and
remove the radio.
6. Install the optional pocket (Scosche part #1001518) by reversing procedures 1 through 4.
1995-02 Chevrolet / GMC Full Size Pickup
1992-02 Chevrolet / GMC Suburban
1995-02 Chevrolet Tahoe
1995-00 GMC Crewcab / Dually Pickup
1992-02 GMC Yukon
1999-99 GMC Yukon Denali
2000-02 GMC Yukon XL
CAUTION:
REAR SUPPORT IS
ESSENTIAL TO THE
INSTALLATION'S
STRUCTURAL
INTEGRITY.
NOTE: SNAP SHAFT MOUNTING
TABS NOT INCLUDED. IF
REQUIRED FOR YOUR STEREO
INSTALLATION, CALL
800-621-3695 X3 FOR IMMEDIATE
SHIPMENT
Produktspezifikationen
| Marke: | Scosche |
| Kategorie: | Auto Kit |
| Modell: | GM1488B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Scosche GM1488B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Auto Kit Scosche
7 Mai 2024
3 April 2024
25 März 2024
21 März 2024
19 März 2024
13 Februar 2024
11 Dezember 2023
2 Dezember 2023
16 November 2023
13 November 2023
Bedienungsanleitung Auto Kit
- Auto Kit Belkin
- Auto Kit Hama
- Auto Kit Kensington
- Auto Kit Manhattan
- Auto Kit Manta
- Auto Kit SilverCrest
- Auto Kit Trust
- Auto Kit Thule
- Auto Kit Maginon
- Auto Kit Blaupunkt
- Auto Kit Kenwood
- Auto Kit Caliber
- Auto Kit Lenco
- Auto Kit Pioneer
- Auto Kit Jabra
- Auto Kit Motorola
- Auto Kit Nokia
- Auto Kit Livoo
- Auto Kit Garmin
- Auto Kit Novero
- Auto Kit Plantronics
- Auto Kit Sony Ericsson
- Auto Kit SuperTooth
- Auto Kit Parrot
- Auto Kit EnVivo
- Auto Kit Alpine
- Auto Kit Urban Revolt
- Auto Kit Uniden
- Auto Kit Magellan
- Auto Kit TomTom
- Auto Kit AHG
- Auto Kit BURY
- Auto Kit HTC
- Auto Kit Mr Handsfree
- Auto Kit Boss
- Auto Kit Jensen
- Auto Kit Interphone-Cellularline
- Auto Kit Veho
- Auto Kit WAGAN
- Auto Kit NAV-TV
- Auto Kit Metra
- Auto Kit PAC
- Auto Kit Havis
Neueste Bedienungsanleitung für -Kategorien-
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
23 August 2024
22 August 2024
22 August 2024
22 August 2024