Rosières RT 923/1 Bedienungsanleitung

Rosières Dunstabzugshaube RT 923/1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Rosières RT 923/1 (10 Seiten) in der Kategorie Dunstabzugshaube. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/10

WARNING

--------------------------------------------------------

The distance between the hob and the lower

part of the hood must be at least 65 cm.

The air collected must not be conveyed

into a duct used to blow off smokes from

appliances fed with an energy other than

electricity (central heating systems, ther-

mosiphons, water-heaters, etc.).

Comply with the official instructions provided

by the competent authorities in merit when

installing the disposal duct. In addition,

exhaust air should not be discharged into

a wall cavity, unless the cavity is designed

for that purpose.

The room must be well aerated in case a

hood and some other heat equipment fed

with an energy other than electricity (gas,

oil, coal heaters, etc) operate at the same

time. In fact the intake hood, disposing of

air, could create a vacuum in the room.

The vacuum should not exceed 0,04mbar.

This prevents the gas exhausted by the

heat source from being intaken again. It is

therefore advisable to ensure the room

contains air taps able to ensure a steady

flow of fresh air.

Check the data label inside the

appliance; if the symbol ( ) is printed,

read the following: this appliance has

such technical particulars that it

belongs to class II insulation, therefore

it must not be earthed.

The following warning is valid in the United

Kingdom only: as the colours of the wires

in the mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals in your plug,

proceed as follows:

– the wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black;

– the wire which is coloured brown must

be connected to the terminal which is

marked with the letter L or coloured red.

– terminal of a three-pin plug.

Check the data label inside the applian-

ce; if the symbol ( ) is NOT printed,

read the following: ATTENTION: This

English

appliance must be grounded. When

making the electrical connections, check that

the current socket has a ground connection.

The following warning is valid in the United

Kingdom only: as the colours of the wires

in the mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals in your plug,

proceed as follows:

– the wire which is coloured green and

yellow must be connected to the terminal

in the plug which is marked with the letter

E or by the earth symbol [ ], or coloured

green or green and yellow;

– the wire which is coloured blue must

be connected to the terminal which is

marked with the letter N or coloured black;

– the wire which is coloured brown must

be connected to the terminal which is

marked with the letter L or coloured red.

When making the electrical connections,

check that the voltage values correspond

to those indicated on the data plate inside

the appliance itself.

In case your appliance is not furnished with

a non separating flexible cable and has no

plug, or has not got any other device ensu-

ring omnipolar disconnection from the elec-

tricity main, with a contact opening distance

of at least 3 mm, such separating device

ensuring disconnection from the main must

be included in the fixed installation.

Always switch off the electricity supply before

carrying out any cleaning or servicing

operations on the appliance.

USE

--------------------------------------------------------

Avoid using materials which could cause

spurts of flame (flambées) near the ap-

pliance.

When frying, take particular care to prevent

oil and grease from catching fire. Already

used oil is especially dangerous in this re-

spect. Do not use uncovered electric grates.

To avoid possible risks of fire always comply

with the indicated instructions when cleaning

anti-grease filters and when removing

grease deposits from the appliance.

MAINTENANCE

--------------------------------------------------------

Thorough servicing guarantees correct and

long-lasting operation.

Particular care must be paid to the anti-

grease filters which must be periodically

cleaned in relation to use (at least once

every two months). Remove the anti-

grease filters and wash them either by

hand or in the dishwasher using neutral

detergent. To take off the anti-grease filters:

at the handle, push the stop inwards and

pull the filter downwards (Fig.3); open the

trolley and take off the other filter doing the

same.

Any fat deposits should be removed from

the appliance periodically depending on

amount of use (at least every 2 months).

Avoid using abrasive or corrosive products.

To clean painted appliances on the outside,

use a cloth dipped in lukewarm water and

neutral detergent. To clean steel, copper

or brass appliances on the outside, it is

always best to use specific products,

following the instructions on the products

themselves. To clean the inside of the

appliance, use a cloth (or brush) dipped in

denatured ethyl alcohol.

DESCRIPTION

--------------------------------------------------------

The appliance can be a filtering version one,

a ducting version one or with an external

motor.

In the Filtering version (Fig. 1), the air and

vapours conveyed by the appliance are depu-

rated by charcoal ﬁlter and recirculated around

the room. ATTENTION: Using the hood as a

ﬁltering one it is necessary to use the char-

coal ﬁlter that puriﬁes the air sent back into

the room.

In the Ducting version (Fig. 2), cooking va-

pours and odours are conveyed straight out-

side by a disposal duct which passes through

the wall/ceiling. Use of charcoal ﬁlter is there-

fore unnecessary.

In the version with an External motor (Fig.

3), the appliance must be connected to an

ducting apparatus/motor which works on its

own using the appliance as a union for the air

to be scavenged. Use only motors pro-

posed in the original catalogue.

According to the model you have bought, the

appliance can include 1 or 2 motors. In the I

motor version the flange for the air to be

exhausted has not got a central position, but

it is slightly on the left.

INSTALLATION

--------------------------------------------------------

Before assembling, in order to manoeuvre the

appliance more easily, take off the anti-grease

filters: at the handle, push the stop inwards

and pull the ﬁlter downwards (Fig. 4); open the

trolley and take oﬀ the other ﬁlter doing the

same.

IMPORTANT: So as not to damage your

product, during installation USE ONLY THE

SCREWS PROVIDED. Make sure these are

used as shown in the following

instructions.

To compensate possible depth voids be-

tween the appliance and the wall, a plastic

SPACING BAR to be ﬁxed at the back of

the appliance by means of the three

screws A is included (Fig. 5). The 3 screws

A to be used are contained in the acces-

sory bag attached to the plastic spacing

bar. Cut the spacing bar according to the

distance to be adjusted.

Assembly under a pensile cupboard

The following operations are essential for

assembly:

– Install the wiring system

– Prepare the air venting hole if your

appliance is to be installed in the ducting

version or in the version with an external

motor.

In the Ducting version and in the version with

an External motor, to get optimal conditions

the air venting pipe should:

– be as short as possible.

– have the lowest number of bends (max

bende angle: 90°).

– be made of material approved by local

authorities (according to the State).

– have its inner side as regular and smooth

as possible.

It is moreover recommended to avoid drastic

changes of pipe cross section (recommended

diameter: 125 mm).

Fixation as indicated in Fig. 6:

Using the relative template make the 4

necessary fixing holes in the bottom of

the cupboard and cut the air venting hole.

For the version with an External motor,

make the electrical connection between

the hood and the external motor by means

of the proper terminal board (Fig. 8): take

oﬀ the cable clamp A and the cover B of

the wiring junction box. Fix the connec-

tion cable of the motor onto the terminal

board C. Reassemble the cable clamp A

and the cover B of the junction box. The

other end of the cable must be ﬁxed onto

the terminal board of the external motor.

Move the hood close to the bottom of the

wall unit and then connect the two units

by means of the 4 self-tapping screws

supplied together with the appliance.

Fixation with brackets as in Fig. 7 (optio-

nal):

Take the two brackets (S) out of the

accessory bag together with the 8 screws

provided. Fit the brackets to the wall unit

being careful to position these correctly;

for this operation use the 4 longer screws.

At this point, secure the appliance to the

brackets using the 4 shorter screws.

Ducting version and version with an External

motor: connect the ﬂange of the hood with the

air venting hole made previously in the wall/

ceiling by means of an adequate tube. Make

the electrical connection of the hood by means

of the power supply cable. Reassemble the

anti-grease filters.

Filtering version: connect a proper pipe to the

flange of the hood so that the air is sent

outside the pensile and sent back into the

room. Make the electrical connection of the

hood by means of the power supply cable.

Assemble the charcoal filter minding that it

restains properly against edge A (Fig. 12).

Reassemble the anti-grease filters.

OPERATION

--------------------------------------------------------

Controls of Fig. 9:

Switch C: position A (automatic), the motor

and the light are automatically regulated

ON or OFF by the opening/closing of the

truck. Position M (manual), the light is on.

Position 0, the light is off.

Switch B: it select the speed of the motor.

Opening the truck, the motor works automati-

cally at the last working speed.

Controls of Fig. 10:

Switch C: position M (motor): the motor

switches ON/OFF by opening/closing the

truck; the lights are always OFF.

Position T (total): the motor and the lights

switch ON/OFF by opening/closing the

truck.

Position L: the lights switch ON and the

motor switch OFF either if the truck is

open or closed; the motor is always OFF.

Switch B: it select the speed of the motor.

When the switch is in M or T position, opening

the truck, the motor starts working automati-

cally at the selected speed.

Controls of Fig. 11:

Switch D: position A (automatic), the motor

and the light are automatically regulated

ON or OFF by the opening/closing of the

truck. Position M (manual), the light is on.

Position 0, the light is off.

Opening slightly the truck, the motor works at

the I speed; opening a bit more, the motor

works at the II speed; opening totally the

truck, the motor works at the III speed.

In case the hood is a filtering version one, it

is necessary to change the charcoal filters

according to utilization about every six month.

To remove the charcoal filter:

– open the truck pulling it frontwards.

– take off the anti-grease filter: where the

handle is, pull the stop inwards and pull

the filter downwards (Fig. 4);

– grasp the tongue of the charcoal filter

pulling it towards the rear of the apparatus

and, at the same time, downwards (Fig.

12-13). Attention: to take off the charcoal

filter, this one must restain properly against

edge A (Fig. 12).

Light bulb

If the fluorescent light need changing,

slacken the light cover by disconnecting the

screw and remove the bulb itself (Fig. 14).

Replace with a bulb of the same type.

To change the rectangular halogen bulbs

open the cover and remove the bulb without

touching it with bare hands (Fig.15). Replace

with a bulb of the same type.

MONTAGE UND

GEBRAUCHSANWEISUNG

--------------------------------------------------------

Das Gerät ist so zu montieren, daß der

Abstand zwischen den Kochplatten und

dem unteren Rand der Dunstabzugshaube

mindestens 65 cm beträgt.

Ein Anschluss der Abluftleitungen an

Verbrennungsabgaskamine (zum Beispiel

Zentralheizung, Heizgeräte, Badezimmer-

öfen usw.) ist nicht gestattet.

In jedem Fall sind bei der Ableitung der

Abluft die behördlichen Vorschriften zu

beachten. Desweiteren darf die Abluft nur

dann durch ein Loch in der Wand geleitet

werden, wenn dieses für diesen Zweck

bestimmt ist.

Achtung! Bei gleichzeitigem Betrieb einer

Abluft-Dunstabzugshaube und einer ra-

umluftabhängigen Feuerstätte (wie z. B.

gas-, öl- oder kohlebetriebene Heizgeräte,

Durchlauferhitzer, Warmwasserbereiter) ist

Vorsicht geboten, da beim Absaugen der

Luft durch die Dunstabzugshaube dem

Aufstellraum die Luft entnommen wird, die

die Feuerstätte zur Verbrennung benötigt.

Ein gefahrloser Betrieb ist möglich, wenn

bei gleichzeitigem Betrieb von Haube und

raumluftabhängiger Feuerstätte im Aufstell-

raum der Feuerstätte ein Unterdruck von

höchstens 0,04 mbar erreicht wird und

damit ein Rücksaugen der Feuerstätten-

abgase vermieden wird. Daher den Raum

mit Lüftungsanschlüssen versehen, die

einen konstanten Zustrom von Frischluft

gewährleisten.

Das Typenschild im Innern des Geräts

kontrollieren: Den folgenden Anwei-

sungen folgen, falls das Symbol ( )

erscheint; dieses Gerät weist kons-

truktive technische Details auf, die

unter die Isolierungsklasse II fallen und

deshalb muss es nicht geerdet werden.

Das Typenschild im Innern des Geräts

kontrollieren: den folgenden Anwei-

sungen folgen, falls das Symbol ( )

erscheint; ACHTUNG: dieses Gerät

muss geerdet werden. Beim elektrischen

Anschluss sicherstellen, dass die Steckdose

Deutsch

eine Erdung aufweist.

Beim elektrischen Anschluss muss überprüft

werden, ob die Spannungswerte des

Stromnetzes mit den Werten auf dem im

Innern des Gerätes angebrachten Typens-

childs übereinstimmen. Falls Ihr Gerät nicht

mit einem fest angeschlossenem Kabel mit

Stecker oder einer sonstigen Vorrichtung,

die eine allpolige Unterbrechung mit einer

Kontaktöffnung von mindestens 3 mm

versehen ist, so müssen die entsprechen-

den Trennvorrichtungen bei der festen

Installation vorgesehen werden

Vor jeder Reinigungs- oder Wartungsarbeit

muss das Gerät vom Stromnetz getrennt

werden.

GEBRAUCH

--------------------------------------------------------

In der unmittelbaren Nähe des Geräts die

Benutzung von flammenerzeugenden

Materialien (Flambieren) vermeiden.

Beim Frittieren besonders auf die Brand-

gefahr achten, die durch Öl und Fette

verursacht wird. Besonders gefährlich ist

die Entﬂammbarkeit von bereits benutztem

Öl. Keine oﬀenen Elektrogrills verwenden.

Zur Vermeidung einer möglichen Brandge-

fahr die Anweisungen zur Reinigung der

Fettfilter und zur Entfernung eventueller

Fettablagerungen auf dem Gerät beachten.

WARTUNG

--------------------------------------------------------

Nur eine sorgfältige Pflege garantiert auf

Dauer eine gute Leistung und Funktion

des Geräts.

Besonders wichtig ist die Reinigung der

Fettfilter. Hierzu sind die Metallfilter

abzunehmen. Die Reinigung wird von Hand,

mit biologisch abbaubarem

Reinigungsmittel, oder in der Spülmaschine

empfohlen. Die Reinigungshäuﬁgkeit hängt

ab von der Benutzungsdauer und der Art

der abzusaugenden Wrasen. Zum

Enfgernen der Entfettungsfilter: in

Überreinstimmung mit dem Handgriff den

Feststeller nach innen stossen und den

Filter nach unten ziehen (Abb. 3);

Schiebegestell öffnen und den zweiten Filter

auf die gleiche Weise herausnehmen.

Die Entfernung eventueller

Fettablagerungen vom Gerät erfolgt in

regelmäßigen Abständen in Abhängigkeit

von der Benutzung (zumindest alle zwei

Monate). Die Verwendung von

scheuernden oder korrosiven Produkten

vermeiden. Für die äußere Reinigung von

lackierten Geräten ein mit lauwarmen

Wasser und Neutralreiniger angefeuchtetes

Tuch verwenden; für die äußere Reinigung

der Geräte aus Stahl, Kupfer und Messing

wird die Verwendung von Spezialprodukten

Produktspezifikationen

Marke:	Rosières
Kategorie:	Dunstabzugshaube
Modell:	RT 923/1
Breite:	900 mm
Tiefe:	380 mm
Produktfarbe:	Silber
Höhe:	170 mm
Typ:	Unterbaut
Geräuschpegel:	58 dB
Maximale Absaugleistung:	260 m³/h
Motorleistung:	200 W
Anzahl Geschwindigkeiten:	3
Anzahl an Lampen:	2 Glühbirne(n)
Lampenleistung:	20 W
Einbaufähigkeit:	Ja
Anzahl Filter:	4 Stück(e)
Anzahl der Motoren:	2
Leuchtmitteltyp:	Halogen
Fettfiltertyp:	Metall