Rosières RDR61/1AV Bedienungsanleitung

Rosières Dunstabzugshaube RDR61/1AV

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Rosières RDR61/1AV (24 Seiten) in der Kategorie Dunstabzugshaube. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/24

INSTRUCTIONS FOR INSTALLATION AND USE

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'INSTALLATION ET L’UTILISATION

ISTRUZIONI PER L'INSTALLAZIONE E L’USO

INSTRUCCIONES PARA INSTALACIÓN Y USO

AANWIJZING VOOR GEBRUIK EN INSTALLATIE

ENGLISH

DESCRIPTION

The unit can be found in filtering hoods or in exhaust hoods. In the hoods (Fig. 1) the air and steamFiltering

taken up by the unit are purified with charcoal filters and returned to the environment through the aeration grids on

the side of the flue. WARNING: When using filtering hoods, both charcoal filters and an air deflector (A) must be

used. Located in the lower part of the flue, this deflector recycles the air to the environment. The charcoal filters are

not supplied. In the hoods (Fig .2) an exhaust duct conveys the steam and cooking odors directly outsideExhaust

through the wall/ceiling. Therefore they do not require charcoal filters.

INSTALLATION

To facilitate installation, before starting remove the : press inward on the clamp at the handle andgrease filters

pull the filter downward (Fig. 3).

Mount the plate of the electrical system (depending on the model) fixing it with 2 screws and 2 metal washers

(Fig. 4).

Wall fitting (Fig. 5): making use of the appropriate drilling jig, apply the supplied blocks into the wall, and

remember the distance between the hood and the cooktop must be at least 65 cm. Insert two of the supplied screws

so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance (use

the holes A; if the hood have the holes A and C, use only the holes C). Once the apparatus is hooked, fix it

definitively to the wall using the two other screws and the holes made at its bottom (B). To avoid damage make

exclusive use of the holes already prepared on the hood.

Securing the telescopic flue: Basic installation requirements: – Set the electrical power supply within the space

covered by the decorative flue. – If your unit is installed in an Exhaust hood, prepare the air exhaust hole.

Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches

on the centre of the bracket (Fig. 6); using a pen, mark the 2 holes on the wall and then make the holes and

fit the screw anchors provided and proceed to secure the bracket using the 2 screws (provided).

Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock it to

the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all power

connections to the hood by means of the power cable. Take 2 assembled flues and place these on the upper surface

of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.7).

Filtering hood: make all power connections to the hood using the power cable. Fasten the air baffle to the lower

flue as shown in Figure 8, using the 2 screws. Take 2 assembled flues and place these on the upper surface

of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.7).

Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such

filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:

- if the hood features round charcoal filters (Fig. 9), fit the charcoal filter by turning anti-clockwise.

- if the hood features a panel type charcoal filter (Fig. 10), remove the two metal filter retainers (M) and position

the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 11: Button A: light switch. Button B: first speed motor ON/OFF switch. Button C: second

speed switch. Button D: third speed switch. E: motor on light. THE MOTOR FUNCTION WARNING LIGHT (E) IS

NOT PRESENT IN SOME MODELS.

Controls shown in Fig. 12: Button A: Light switch; position 0: light off; position 1: light on. Button B: Motor

switch; position 0: motor off; position 1-2-3: motor on at speed I, II and III. C: Motor pilot lamp.

Controls shown in Fig. 13: Button A: turns the LIGHTS off. Button B: turns the LIGHTS on. Button C: decreases

speed down to minimum speed. If pressed for 2" the motor is turned off. Button D: activates the motor (calling

the last speed used) and increases the speed until reaching maximum. Button E: FILTER ALARM/TIMER RESET:

when pressing the key during display of the filter alarm (motor off) it resets the hour counter. When pressing the

key when the motor is running, the TIMER is activated and the hood will automatically be switched off after 5

minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM: After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter

(RESET) by pressing the key E during display of the filter alarm.

Controls shown in Fig. 14: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot

lamp (S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the

corresponding pilot lamp (S) flashes to indicate that the grease filters must be cleaned and the charcoal filter

replaced. To restart the hour counter (RESET), hold the button A pressed down for about 1” (while the pilot lamp

S is on). Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down

for about 1”, the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER

is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button C: drives the motor in second speed

(the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) ,

the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button D: drives the motor in

third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp

is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button E: drives the

motor in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while

the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes).

Pay special attention to the to remove the filter: push inward on the clamp at the handle andgrease filters;

pull the filter downward. Wash out the filter using a neutral soap. if the model purchased has the controls shown

in Figure 13: see the paragraph “Controls shown in Fig. 13” (“Filter Alarm”). If the model purchased has the controls

shown in Figure 11/12: the grease filter must be cleaned periodically: exactly how often depends on use (at least

once every other month). If the model purchased has the controls shown in Figure 14: the grease filters must

be cleaned approximately once every 30 hours of operation (when the light button lamp comes on) - Fig. 14S).

Once the cleaned filters are reinstalled, to reset the counter hold the light button pressed down for about 1”

(Fig.14A) while the corresponding pilot lamp (S) is on. For further information, see the Controls in Fig.14 in the

paragraph entitled “Operation”.

Charcoal filter/s: if using the hood in the filtering hood, the charcoal filter must be replaced periodically. To

remove the charcoal filters, proceed as follows, depending on the model purchased:

- if the hood features round charcoal filters (Fig. 15), remove the charcoal filter by turning clockwise.

- if the hood features a panel type charcoal filter (Fig. 10), remove the charcoal filter by first of all removing the

two filter retainers M.

If the model purchased has the controls shown in Figure 13, see the paragraph “Controls shown in Fig. 13” (“Filter

Alarm”). If the model purchased has the controls shown in Figure 11/12, the charcoal filters must be replaced

according to use: on the average once every 6 months. If the model purchased has the controls shown in Figure14,

the charcoal filters must be replaced each time the light button (Fig.14S) lamp flashes (i.e. every 120 hours of

operation).

Lighting:

- To gain access to the , remove the grease filters as described above and remove the bulbs.incandescence bulbs

Replace with lamps of the same type.

- If the shown in Fig. 16 need changing, slacken the ring nut in an anticlockwise direction andhalogen lamps

remove the bulb itself. Replace with the same type of lamp. CAUTION: Do not handle glass bulb with bare hands.

- To change the shown in Fig. 17 open the cover levering from the proper slots. Replace withhalogen lamps

the same type of lamp. CAUTION: Do not handle glass bulb with bare hands.

The motor used in this hood features a safety device (thermal cutout) that responds to temperature changes

For accidental reasons or due to installation faults, this device could engage and automatically shut off the

motor, thereby preventing serious damage to the equipment. In such cases, after allowing the motor to cool

down, the hood can be switched on again; the cause of the fault will nonetheless have to be remedied,

ensuring installation has been correctly made and that all the instructions in the Information sheet have been

complied with.

DEUTSCH

GERÄTEAUSFÜHRUNG

Das Gerät kann in Umluftversion und in Abluftversion geliefert werden. In der (Abb. 1) werdenUmluftversion

die durch das Gerät geleitete Luft und der Dampf durch Kohlefilter gereinigt und dann über die seitlichen Lüftungsgitter

der Haube wieder in Zirkulation gebracht. ACHTUNG: Bei Verwendung der Umluftversion sind ein Kohlefilter und ein

Luftableitblech (A) notwendig, das in den unteren Teil des Rohrs eingebaut wird und ein erneutes Einleiten der Abluft

in den Raum ermöglicht. Die Kohlefilter werden nicht mitgeliefert. In der (Abb. 2) werden die DämpfeAbluftversion

und Küchengerüche direkt über eine Evakuationsöfffnung in der Wand oder Decke nach außen abgezogen. Daher

sind keine Kohlefilter notwendig.

MONTAGE DES GERÄTS

Vor den Montageoperationen muß/müssen zur leichteren Handhabung des Geräts die entfernt werden:Fettfilter

Den Festhalter in der Nähe des Griffs nach innen drücken und den Filter nach unten ziehen (Abb. 3).

Die Platte der elektrischen Anlage anbringen (Je nach Version) und mit 2 Schrauben und 2 Unterlegscheiben aus

Metall befestigen (Abb.4).

Befestigung an der Wand (Abb. 5): Benutzen Sie die Bohrschablone, um die Dübel in der Wand anzubringen,

wobei der Abstand zwischen der Haube und dem Kochfeld mindestens 65 cm betragen muß. Nun kann das Gerät

mit den Schlüssellochöffnungen in der Geräterückwand in die Schrauben eingehängt werden (die Oeffnungen A

benutzen; wenn in der Haube die Oeffnungen A und C vorhanden sind, dann muessen nur die Oeffnungen C

benutzt werden). Zusätzlich wird das Gerät durch die Sicherungslöcher fest mit der Wand verschraubt (B). Um

Produktspezifikationen

Marke:	Rosières
Kategorie:	Dunstabzugshaube
Modell:	RDR61/1AV

Brauchst du Hilfe?

Wenn Sie Hilfe mit Rosières RDR61/1AV benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Dunstabzugshaube Rosières

Rosières RHP 9700 PN Bedienungsanleitung

15 Oktober 2024

Rosières RDM 101 IN Bedienungsanleitung

2 Oktober 2024

Rosières RHG580/1IN/1 Bedienungsanleitung

2 Oktober 2024

Rosières RHG527/1RB Bedienungsanleitung

23 September 2024

Rosières RHG527PN Bedienungsanleitung

22 September 2024

Rosières RHT 6300/1 LIN Bedienungsanleitung

22 September 2024

Rosières RHC927PN Bedienungsanleitung

14 September 2024

Rosières RHG 580 PN Bedienungsanleitung

8 September 2024

Rosières RHG 545 RB Bedienungsanleitung

8 September 2024

Rosières RHT6300/2LPN-ALG Bedienungsanleitung

5 September 2024

Bedienungsanleitung Dunstabzugshaube

Neueste Bedienungsanleitung für -Kategorien-

Pelgrim ISW990 Bedienungsanleitung

16 Oktober 2024

Amana UVL6048JSS Bedienungsanleitung

16 Oktober 2024

Maytag UVL6048JSS Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GTW Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GW Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GB Bedienungsanleitung

16 Oktober 2024

Freggia CHS46B Bedienungsanleitung

16 Oktober 2024

Freggia CHS45X Bedienungsanleitung

16 Oktober 2024

Freggia CHS45W Bedienungsanleitung

16 Oktober 2024

Freggia CHS45B Bedienungsanleitung

16 Oktober 2024