Pyle SBA10A Bedienungsanleitung

Pyle Subwoofer SBA10A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle SBA10A (5 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war für 27 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/5
SBA10A
10” 900 Watts Low-Profile Active Amplified
Car Audio Subwoofer System
Suitable for Under-seat Installations
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.P USA.comyle
2www.Py U comle SA. 3
Introduction
With the SBA10A
high-powered subwoofer system to your audio system.
SBA10A features low pass crossovers, and a control for
adjusting the input sensitivity from 0.12V to 3.5V.
Both high level (speaker level) and low level (RCA type) inputs are present, making this a
universal solution for use with any head unit or other input source.
included. You can control the subwoofer level with the remote level control module.
Mounting the Subwoofer
A typical location is shown below:
3. Mark the location for mounting hole screws by positioning the cabinet where you wish to
install it. Make a small mark to identify the position and remove the unit. Thoroughly clean
the area you plan to attach the subwoofer, using a vacuum cleaner and press down on it
securely.
Control Panel and Features
1. POWER ON LED INDICATOR
2. PROTECT LED INDICATOR
3. PHASE SHIFT: Use this switch to help compensate for time alignment problems in the
from the listener than the other speakers in the system.
4. AUTO POWER ON: During ON mode, It’s not necessary to connect the remote cable if
you’re using the high level inputs. Do not function with the RCA inputs. On the contrary
while it is during AUTO POWER OFF mode that it needs remote cable connection to turn
on the unit.
5. LOW PASS FILTER:
BELOW the
frequency you set. If the rest of your system is weak on the mids, you may wish to set this
control relatively high. If the midrange is well vered by the rest of your system, you willco
probably want the subwoofer to only receive lower frequency signal.
6. BASS BOOST: The bass boost feature will increase the sound level the bass frequencies.
7. INPUT CGAIN ONTROL: After yo av stalled yu h e in our yst s em, turn this control to minimum.
Turn the head unit on (and the subwoofer will turn on via the remote connection).
Turn the head unit volume to about 2/3 full level. Slowly turn up the subwoofer input
gain control until you hear a small amount of distortion. Then reduce the level until the
distortion is completely gone. Leave the control at this setting.
8. REMOTE LEVEL CONTROL PORT: Attach the included remote level control to cotrol the
volume level of the subwoofer independently.
9. HIGH LEVEL (speaker level) INPUTS: If your head unit does not have RCA outputs, you
can use the speaker outputs for the audio source for the . USBA10A se the suppl ableied c
and co ec outnn t e th puts properly as ow nsh n i the co ecti diann on gram in his ma t nual.
10. LOW LEVEL RCA INPUTS: Low level inputs are the recommended way to introduce the
audio signal to the subwoofer if RCA outputs are present on your head unit or other
signal source (such as a sound processor).
11. FUSE: NEVER
replace the fuse with a wire or coin.
12. POWER TERMINALS
www.P USA.comyle
4www.Py U comle SA. 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance.
M t tr r at bos unk o h ch ack nst ll ti ns will i a a o r uir a fo RCA ableeq e 15-20 ot c , w ile pic up trunkh k s
and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality
cable.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
High Level Input Wiring
The high level input(s) should only be used when your receiver lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver to the
problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
Power Connections
Connect the ground terminal to the closest point on the chassis of the vehicle.
Keep this ground wire to less than 39” (100 cm) inlength. Use 8 gauge (or heavier) wire.
AUTO POWER ON
the head unit using 16 gauge (or heavier) wire. Connect an empty fuse holder within 18” (45
location. Then connect the fuse holder to the “BATT+” connection on the subwoofer rear
panel.
Remote Level Control Connection
Instal the remote control securely under the
dash or in a similar location where using it will
not distract the driver.
To REMOTE TURN-ON
terminal of head unit

Produktspezifikationen

Marke: Pyle
Kategorie: Subwoofer
Modell: SBA10A

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle SBA10A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Subwoofer Pyle

Pyle

Pyle PLRVST400 Bedienungsanleitung

29 September 2024
Pyle

Pyle PLMW63 Bedienungsanleitung

21 September 2024
Pyle

Pyle PLMRK47BK Bedienungsanleitung

11 September 2024
Pyle

Pyle UPLBN122 Bedienungsanleitung

7 September 2024
Pyle

Pyle PSSUB101 Bedienungsanleitung

4 September 2024
Pyle

Pyle PSBS8 Bedienungsanleitung

2 September 2024
Pyle

Pyle PLR38I Bedienungsanleitung

31 August 2024
Pyle

Pyle PLRG23C Bedienungsanleitung

31 August 2024
Pyle

Pyle PLND35 Bedienungsanleitung

31 August 2024
Pyle

Pyle PLML50FB Bedienungsanleitung

12 August 2024

Bedienungsanleitung Subwoofer

Neueste Bedienungsanleitung für -Kategorien-

Pioneer

Pioneer S-21W Bedienungsanleitung

13 Oktober 2024
JL Audio

JL Audio SGR-10TW3 Bedienungsanleitung

13 Oktober 2024
Polk

Polk DB1040 Bedienungsanleitung

10 Oktober 2024
Blaupunkt

Blaupunkt GBW801 Bedienungsanleitung

7 Oktober 2024
JL Audio

JL Audio TW1 Bedienungsanleitung

6 Oktober 2024
Jensen

Jensen J12W Bedienungsanleitung

6 Oktober 2024
Musway

Musway MT169Q Bedienungsanleitung

6 Oktober 2024
JL Audio

JL Audio 12W0v3 Bedienungsanleitung

4 Oktober 2024
Yamaha

Yamaha YST-SW315PN Bedienungsanleitung

2 Oktober 2024
JBL

JBL SW10 Bedienungsanleitung

30 September 2024