Pyle PLUTV63BTA Bedienungsanleitung

Pyle Lautsprecher PLUTV63BTA

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PLUTV63BTA (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
5
Marine/PowerSports Tower Technical Specs:
Speaker Power: 1200 Watt MAX
Amp Power: 2 x 250 Watt MAX @ 4 Ohms (2 x 125 Watt RMS)
Amp Type: 2-Channel, Class D
Marine Grade Waterproof Rating: IP-X6
Speaker Type: Polypropylene Cone, Butyl Rubber Surround (x2)
Tweeter Type: Neodymium Dome (x2)
Impedance: 4 Ohm
Magnet Type: 32 oz. Circuit
Mid-Woofer Voice Coil Type: 1'', TIL
Sensitivity: 92 dB +/- 2 dB @ 1M/1W
Anti-Thump Turn-On
Soft Turn On/O
T.H.D: <0.05%
S/N Ratio: >80dB
Channel Separation: >65dB
Fuse: 1 x 15A
Power Supply: DC 12V
Universal Mounting Brackets Roll-Bar/Roll-Cage Diameter: 1.75’ ~ 3.0’ –inches
1.75”~2” for Motorsports/Powersports Application.
2.25”~3” for Marine Application.
Speaker Dimensions: 8.1’ x 8.9’ x 10.5’ -inches, with Bracket (-Each)
www.PyleUSA.com
PLUTV63BTA Installation
Speaker Mounting suggestion as below:
Step 1: Removing the top half of clamp
Put the PLUTV63BTA speaker in a safe place.
Using the 1/4” Hex key, remove the top clamp bolts.
Step2/3: To adjust mounting clamp angle and speaker position
Diagram A is to show there are four round pins underneath the bottom
base of aluminum die cast clamp, which can be inserted and xed to four
round notch holes on top of plastic cabinet as diagram B shows by every
45 degrees adjustment either at clockwise or counter clockwise direction.
Through such design, user can change the angle of swivel clamp, use the
5/16” hex key to loose the center screw a little bit and lift the bottom clamp
to twist speaker angle by every 45 degrees to get the optimal angle you
want. Then re-making sure the pins on base of bottom clamp are inserted
and sits on notch holes on top of plastic cabinet at and seamlessly.
Then re-tighten the center hex screw to secure the bottom clamp strongly.
2
www.PyleUSA.com
Step 4: Securing clamp bolts
Using the correct rubber pads (labeled for O.D.) install on both top and
bottom half of clamps. 3.15” x 1.2” x 0.2” rubber pads for 1.75” O.D. 3.15” x
1.2” x 0.08” rubber pads for 2” - 3” O.D. Using the 1/4” Hex bit socket hand
tighten the bolts evenly (both sides should have the same spacing
between bolts).
Step 5: Option for adjustable PYLE logo---Unbolt the screws rst, adjust the logo
direction, then re-x screws.
PLUTV63BTA Wiring
1. Connect the RCA plugs (red/white) to an external amplier for audio output.
2. Connect the ACC wire (red) to the accessory power of the vehicle as ON/OFF
switch of the speakers.
3. Connect the remote out wire (blue) to an external amplier as ON/OFF switch
of the amplier.
3
www.PyleUSA.com
Features:
Pro Audio PowerSport Speakers
Amplied (Active) Speaker System
Wireless BT Music Streaming Ability
Bridged Sound System: (2) x 6.5'' Woofers + (2) x 1’ Tweeters
Marine Grade Waterproof Rated Construction
Weatherproof & Water-Resistant Housing
2-Way Full Range Stereo Sound Reproduction
Built-in Digital Sound Processing Amplier
Integrated Speaker Power & Wiring Harness
Compact Size & High-Powered Output
Impressive Bass Response
Aux (3.5mm) Input Jack
Connect & Stream Audio from External Devices
Sleek Design, Machine Molded Speaker Cabinet Housing
Rugged, Universal Mount Bracket Design for Roll-Bar/Roll-Cage
Used for O-Road Outdoor Vehicles: ATV, UTV, 4x4, Jeeps, Marine Watercraft
Pre-Amp RCA Out to Any OEM/Factory-Made Mono-Block/Full-Range Amplier
BT Connectivity:
Simple & Hassle-Free Pairing
Instant Wireless Audio Streaming Ability
Works with All of Today’s Latest Devices (Smartphones, Tablets, Laptops, etc.)
BT Version: V5.0
BT Network Name: ‘PyleUSA
Wireless Range: 30+ ft.
*BT Receiver Module Built-Into Amplier of Main / Active Speaker
What’s in the Box:
(1) 6.5'' Amplied Main Speaker
(1) 6.5'' Aluminum Mounting Brackets
(2) 3” Aluminum Mounting Brackets (Pre-Installed on Speakers)
(4) 3.15” x 1.2” x 0.2” Inches Rubber Pads
(4) 3.15” x 1.2” x 0.08” Inches Rubber Pads
(4) M8 x 55mm Hexagon Socket Head Cap Screws
(4) M8 x 35mm Hexagon Socket Head Cap Screws (Pre-Installed)
(1) Power Wire Harness
4
www.PyleUSA.com
12V wire harness connection
Black -
Gray +
AUX input
(2)
ACC wire
(red)
(1)
Audio output
(3)
Remote out
wire (blue)
Ground wire
(black)
Battery wire
(yellow)
DC12 (-) grounded to
metal chassis, or directly
to negative polarity of battery
DC12 (+) extention
power cable with fuse
holder (not included)


Produktspezifikationen

Marke: Pyle
Kategorie: Lautsprecher
Modell: PLUTV63BTA

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PLUTV63BTA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Pyle

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-