Pyle PLUTV42CH Bedienungsanleitung

Pyle Empfänger PLUTV42CH

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PLUTV42CH (10 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/10
PLUTV42CH
800W Waterproof Marine Speakers
+ 2 Ch. Rated Amplifier
ATV, UTV, 4x4, Jeep, Wired RCA, AUX, and MP3 Audio Input Cable,
for Boat Stereo Speaker & Other Watercraft
www.PyleUSA.com
2
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.
• Use speakers with an impedance of 4 Ohms
• Avoid installing the unit where:
• It would be subject to high temperatures, such as from direct sunlight or hot air
from the heater.
• It would be exposed to rain or moisture.
• It would be subject to dust or dirt.
• If your vehicle or boat is parked in direct sunlight and there is a considerable
rise in temperature inside the car, allow the unit to cool off before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns with
the oor carpet.
• If this unit is placed too close to the resources radio, an interference may occur.
In this case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions.Do not attempt to test the protection
circuits by covering the heatsink or connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
• For safety reasons, keep the volume of your audio system moderate so that you
can still hear normal traffic sounds in a reasonable distance.
WIRING INSTRUCTIONS
POWER CONNECTION
The battery terminal (BATT ) must be connected directly to the positive terminal of
the vehicle battery to provide an adequate voltage source and minimize noise.
Connecting the battery terminal lead to any other point (such as the fuse block)
will reduce the power output and may cause noise and distortion. Use only #12
gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal
of the battery after all other wiring is completed.
GROUND CONNECTION
The ground terminal (GND) connection is also critical to the correct operation of
the amplier. Use a wire of the same gauge as the power connection (#8 or thicker)
and connect it between the ground terminal (GND) of the amplier and a metal
part of the vehicle close to the mounting location. This wire should be as short as
possible and any paint or rust at the grounding point should be scraped away to
provide a clean metal surface to which the end of the ground wire can be screwed
or bolted.
www.PyleUSA.com
3
REMOTE TURN-ON CONNECTION
The amplier is turned on by applying +12V to the remote turn-on terminal (REM).
The wire lead to this terminal should be connected to the "Auto-Antenna" lead
from the vehicle/or boat stereo resources which will provide the +12V only when
the stereo resources is turned on . If the car stereo does not provide an "Auto-An-
tenna" lead, the remote turn-on lead may be wired to an "Accessory" or "Radio"
terminal in the vehicle’s/or boat’s fuse block. This will turn the amplier on and off
with the ignition key, regardless of whether the stereo resources is on or off.
The remote turn-on lead does not carry large currents. So #16 gauge wire may be
used for this application.
SPEAKER CONNECTIONS
Depending on the type and number of speakers used with the amplier wire them
to the speaker terminals as per the appropriate wiring diagram. For most applications
#18 gauge wire should be used for the speaker leads but in no case thinner than
#16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When wiring
the speakers, pay careful attention to the polarity of the terminals on the speakers
and make certain they correspond to the polarity of the corresponding terminals
on the amplier. Do not ground any speaker leads to the chassis of the vehicle/or
boat.
OPERATION
After the amplier has been installed and all connections have been made carefully
and securely, turn the radio on so that the amplier is switched on automatically.
After a short power-on period, the amplier reaches its full performance. Now turn
up the volume slowly using the volume control of the radio. If there is no sound or
only a distorted replay, switch off the radio immediately - the amplier will also
switch off automatically - and check if all connections have been made correctly.
GND (-) = GROUND CONNECTION
Connect the GND terminal to the chassis ground of your vehicle/or boat and
take care of best electric and mechanic contact. In doing so, drill a hole into the
vehicle/or boat chassis near the amplier then remove color, dirt or any other
substance from the ground point. Thereafter fasten the cable end with added ring
terminal by using a screw. Ensure that the ground connection is as short as possible
and that the cable diameter is sufficient (min 4mm). Route the ground cables from
the radio and all other equipment parts, like equalizer, active crossover network or
other ampliers, to the same ground point.

Produktspezifikationen

Marke: Pyle
Kategorie: Empfänger
Modell: PLUTV42CH

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PLUTV42CH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Pyle

Pyle

Pyle PTAU45.5 Bedienungsanleitung

22 September 2024
Pyle

Pyle PPG-460A Bedienungsanleitung

14 September 2024
Pyle

Pyle PLMRMB2CW Bedienungsanleitung

11 September 2024
Pyle

Pyle Pro PTAU23 Bedienungsanleitung

6 September 2024
Pyle

Pyle INV500DBA Bedienungsanleitung

5 September 2024
Pyle

Pyle PDA4BU Bedienungsanleitung

3 September 2024
Pyle

Pyle PD1000BA Bedienungsanleitung

1 September 2024
Pyle

Pyle Elite UPLMRA430BT Bedienungsanleitung

1 September 2024
Pyle

Pyle PT1100 Bedienungsanleitung

31 August 2024
Pyle

Pyle PFA100 Bedienungsanleitung

31 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024