Pyle PLUTV40BK Bedienungsanleitung

Pyle Lautsprecher PLUTV40BK

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PLUTV40BK (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
PLUTV40BK
4 Waterproof Rated Off-Road Speakers
900W Compact Power Sport Vehicle
Speaker System for ATV, UTV, 4x4, Jeep (Pair)
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.PyleUSA.com
2
www.PyleUSA.com 3
PLUTV40BK Installation
Please note:
The below instructions refers to most common bar sizes: 1.5”, 1.75” and 2”.
But using the supplied rubber pads will allow you to mount these speakers
on any bar size measured between 1.5” and 2”.
Features:
Pro Audio Power Sport Speakers
Compact & High-Powered Output
Marine Grade Waterproof Rated Construction
Weatherproof & Water-Resistant Housing
Sound System: (2) x 4'' Woofers + (2) x 1” Tweeters
2-Way Full Range Stereo Sound Reproduction
Impressive Bass Response
Sleek Design, Machine Molded Speaker Cabinet Housing
Rugged, Universal Mount Bracket Design for Roll-Bar / Roll-Cage
Used for O-Road Outdoor Vehicles: ATV, UTV, 4x4, Jeeps, Marine Watercraft
Quick Nickel Plated Push-in Terminal for Speaker Wiring
What's in the Box:
(2) O-Road Speakers
(6) Rubber Pads 4.53'' x 1.18'' x 0.12'' -inches
Technical Specs:
Power Output: 900 Watt MAX
Marine Grade Waterproof Rating: IP-X5
Speaker Size: 4” -inch (Each)
Speaker Style: Passive Speakers
Speaker Type: Polypropylene Cone, Butyl Rubber Surround (x2)
Tweeter Type: Neodymium Dome (x2)
Frequency Response: 105Hz-20kHz
Impedance: 4 Ohm
Magnet Type: 30 oz. Circuit
Mid-Woofer Voice Coil Type: 1.0'', KSV
Sensitivity: 90 dB +/- 2 dB @ 1M/1W
Universal Mounting Brackets Roll-Bar / Roll-Cage
Diameter: 1.5” ~ 2.0” -inches
Speaker Dimensions: 5.7” x 8.0” x 7.4” -inches, with Bracket (Each)
Remove the two screws from the
bracket to separate the speaker
pod and the bracket.
Remove the backing o the pad
and wrap it around the bar.
The rubber pads will need to be cut to
length, so they t the speaker pod and
the bracket. After the rubber pads have
been cut, remove the white protective
layer and stick them to the speaker pod
and the bracket.
Screw the two screws evenly, until snug.
Once the position is veried, tighten the
screws another half-turn.
DO NOT OVERTIGHTEN!
Step 1 Remove Both
Screws
Step 2
Screws
Mounting Bracket
Mounting Bar
Step 4
4.5” par
4.5” par
4.5” par
2” Bar
1.75” Bar
1.5” Bar
* The pad should go all the way
around the bar. If the pad is too
long, cut the extra length.
2” Bar doesn’t require
padding.
Step 3


Produktspezifikationen

Marke: Pyle
Kategorie: Lautsprecher
Modell: PLUTV40BK

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PLUTV40BK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Pyle

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-