Pyle PLMRSBA8 Bedienungsanleitung

Pyle Empfänger PLMRSBA8

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PLMRSBA8 (5 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/5
PLMRSBA8
Marine Grade Slim Active Subwoofer
8” 600 Watts Low-Prole Active Amplied Marine
and Waterproof Subwoofer System
Suitable for Under-seat Installations
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.PyleUSA.com
2www.PyleUSA.com 3
Introduction
With the , we are introducing a low-prole amplied subwoofer. Low enough to PLMRSBA8
easily t below the seat of your car. This system oers you a quick and easy way to add a
high-powered subwoofer system to your audio system.
The integrated amplier in the features low pass crossovers, and a control forPLMRSBA8
adjusting the input sensitivity from 0.12V to 3.5V.
Both high level (speaker level) and low level (RCA type) inputs are present, making this a
universal solution for use with any head unit or other input source.
For further exibility in the use of a subwoofer, a variable bass boost control has been
included. You can control the subwoofer level with the remote level control module.
Mounting the Subwoofer
1. Find a suitable location in the vehicle in which to mount the amplier.
A typical location is shown below:
2. Make sure there is sucient air circulation around the intended mounting location.
3. Mark the location for mounting hole screws by positioning the cabinet where you wish to
install it. Make a small mark to identify the position and remove the unit. Thoroughly clean
the area you plan to attach the subwoofer, using a vacuum cleaner and press down on it
securely.
Vehicle seat
Control Panel and Features
1. POWER ON LED INDICATOR
2. PROTECT LED INDICATOR
3. PHASE SHIFT: Use this switch to help compensate for time alignment problems in the
system. Such problems usually result from having the subwoofer at a dierent distance
from the listener than the other speakers in the system.
4. AUTO POWER ON: In OFF mode, It’s not necessary to connect the remote cable if you’re
using the high level inputs. Do not function with the RCA inputs. However, we prefer the
direct remote wiring on a “plus after contact”.
5. LOW PASS FILTER: This control permits you dene the frequency range you want the
subwoofer amplier to receive. The subwoofer will reproduce all sound BELOW the
frequency you set. If the rest of your system is weak on the mids, you may wish to set this
control relatively high. If the midrange is well covered by the rest of your system, you will
probably want the subwoofer to only receive lower frequency signal.
6. BASS BOOST: The bass boost feature will increase the sound level the bass frequencies.
7. INPUT GAIN CONTROL: After you have installed your system, turn this control to minimum.
Turn the head unit on (and the subwoofer will turn on via the remote connection).
Turn the head unit volume to about 2/3 full level. Slowly turn up the subwoofer input gain
control until you hear a small amount of distortion. Then reduce the level until the
distortion is completely gone. Leave the control at this setting.
8. REMOTE LEVEL CONTROL PORT: Attach the included remote level control to cotrol the
volume level of the subwoofer independently.
9. HIGH LEVEL (speaker level) INPUTS: If your head unit does not have RCA outputs, you
can use the speaker outputs for the audio source for the PLMRSBA8. Use the supplied cable
and connect the outputs properly as shown in the connection diagram in this manual.
10. LOW LEVEL RCA INPUTS: Low level inputs are the recommended way to introduce the
audio signal to the subwoofer if RCA outputs are present on your head unit or other
signal source (such as a sound processor).
11. FUSE: The fuse is rated at 25A. Do not use a fuse with a dierent value and NEVER replace
the fuse with a wire or coin.
12. POWER TERMINALS
3
1 2 54 6 7 8 9 10 11 12
www.PyleUSA.com
4www.PyleUSA.com 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance.
Most trunk or hatchback installations will require a 15-20 foot RCA cable, while pickup trunks
and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality
cable.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
High Level Input Wiring
The high level input(s) should only be used when your receiver lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver to the
high level input connector of the amplier. Be sure to observe polarity to avoid audio phase
problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
Power Connections
Connect the ground terminal to the closest point on the chassis of the vehicle.
Keep this ground wire to less than 39” (100 cm) inlength. Use 8 gauge (or heavier) wire.
Connect the remote terminal to the remote output of the head unit using 16 gauge
(or heavier) wire. Connect an empty fuse holder within 18” (45 cm) of the car battery, and run
8 gauge (or heavier) cable from this fuse to the amplier location. Then connect the fuse
holder to the “ ” connection on the subwoofer rear panel.BATT+
Remote Level Control Connection
To Audio outputs of head
unit or signal processor
White L+ Black L-
Grey R+ Black R-
To Speaker Terminals
of head unit
Chassis
ground
point
To REMOTE TURN-ON
terninal of head unit
FUSE
+
Remote
Level Control
Instal the remote control securely under the
dash or in a similar location where using it will
not distract the driver.

Produktspezifikationen

Marke: Pyle
Kategorie: Empfänger
Modell: PLMRSBA8

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PLMRSBA8 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Pyle

Pyle

Pyle PTAU45.5 Bedienungsanleitung

22 September 2024
Pyle

Pyle PPG-460A Bedienungsanleitung

14 September 2024
Pyle

Pyle PLMRMB2CW Bedienungsanleitung

11 September 2024
Pyle

Pyle Pro PTAU23 Bedienungsanleitung

6 September 2024
Pyle

Pyle INV500DBA Bedienungsanleitung

5 September 2024
Pyle

Pyle PDA4BU Bedienungsanleitung

3 September 2024
Pyle

Pyle PD1000BA Bedienungsanleitung

1 September 2024
Pyle

Pyle Elite UPLMRA430BT Bedienungsanleitung

1 September 2024
Pyle

Pyle PT1100 Bedienungsanleitung

31 August 2024
Pyle

Pyle PFA100 Bedienungsanleitung

31 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024