Pyle PLMRC400X4 Bedienungsanleitung

Pyle Empfänger PLMRC400X4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PLMRC400X4 (12 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/12
4-Channel Weather-Resistant Audio Amplifier System
PLMRC400X4
Class D Compact Designed Suit for Car, ATV,
UTV, 4X4, Jeep, Motorcycle and Marine,
and any other Weather Resistant Application
www.PyleUSA.com
2
INTRODUCTION
This power amplier has been designed to provide high quality performance
with a minimum of maintenance. However, it's performance will only be as good
as the care and quality of components with which is installed.
We therefore advise that you read these instructions very carefully to familiarize
yourself with the product and it's features.
Before installing the power amplier please read this instruction manual
carefully. The instructions for mounting and connecting the set have to be
followed precisely. If necessary, a service center should be consulted.
All connections for DC power, signal input and speaker outputs can be carried
out easily and safely byway of RCA and screwed terminals.
INSTALLATION INSTRUCTIONS
Please choose a mounting place without any direct weather inuences.
Note that the amplier generates heat so that a well ventilated place is necessary.
According to your car's construction the set can be made very carefully in order
to ensure the amplier's full performance and reliability.
Keep the wire connections as short as possible with sucient dimensions in
order to minimize power losses and provide a higher audio output of the system.
For safety reasons route all power and speaker wiring by using the exiting wire
channels. To minimize damage to the cables, take care that they do not pass
sharp edged metal. Lay all cables as far away as possible from the ignition cables,
modules in the boot and under the key dashboard, as this create interference.
Add a fuse into the (+) power cable in a distance of not more than 30 cm from
the positive battery pole.
Keep the length of the power wires as short as possible. It is better to use power
cables which are short and then longer speaker cables.
In order to reduce interference, also pay attention to the instructions.
www.PyleUSA.com 3
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 VoIts (DC) operation only
• Use speakers with an impedance of 2 or 4 Ohms (4 to 8 Ohm when used as
bridged amplier)
• Avoid installing the unit where:
•It would be subject to high temperatures, such as from direct sunlight or hot
air from the heater.
•It would be exposed to rain or moisture.
•It would be subject to dust or dirt.
• If your car is parked in direct sunlight and there is a considerable rise in
temperature inside the car, allow the unit to cool o before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns
with the oor carpet.
• If this unit is placed too close to the car radio, an interference may occur in this
case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions.
• Do not attempt to test the protection circuits by covering the heatsink or
connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
• For safety reasons, keep the volume of your car audio system moderate so that
you can still hear normal trac sounds outside your car.
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse
blows again after replacement, there may be an internal malfunction.
In this case, consult your dealer.
WARNING: Use the specied amperage fuse. Use of a higher amperage fuse
may cause serious damage.
PROTECTION CIRCUIT
This amplier is provided with a protection circuit which operates in the
following cases when:
• the unit is overheated.
• the speaker terminals are short circuited.

Produktspezifikationen

Marke: Pyle
Kategorie: Empfänger
Modell: PLMRC400X4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PLMRC400X4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Pyle

Pyle

Pyle PTAU45.5 Bedienungsanleitung

22 September 2024
Pyle

Pyle PPG-460A Bedienungsanleitung

14 September 2024
Pyle

Pyle PLMRMB2CW Bedienungsanleitung

11 September 2024
Pyle

Pyle Pro PTAU23 Bedienungsanleitung

6 September 2024
Pyle

Pyle INV500DBA Bedienungsanleitung

5 September 2024
Pyle

Pyle PDA4BU Bedienungsanleitung

3 September 2024
Pyle

Pyle PD1000BA Bedienungsanleitung

1 September 2024
Pyle

Pyle Elite UPLMRA430BT Bedienungsanleitung

1 September 2024
Pyle

Pyle PT1100 Bedienungsanleitung

31 August 2024
Pyle

Pyle PFA100 Bedienungsanleitung

31 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024