Pyle PDA30BU Bedienungsanleitung

Pyle Empfänger PDA30BU

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PDA30BU (6 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
Wireless Stereo Power Amplifier BT Compatible
PDA30BU
Blue Series Compact and Audio Streaming Amp
with RCA & Speaker Terminals
www.PyleUSA.com
2
Read through this user manual before using the product
to ensure its correct use. Keep this manual for future reference.
Quick Setup:
1. Main Power ON Switch: Switch ON/OFF the amplier by using this switch.
2. --LINE input model --Wireless BT input model.Input LED: RED Green
3. MIC Input
4. Mic volume control: Use this control to set the volume level of Microphone.
5. Adjust to boost or cut LOW frequencies.BASS KNOB:
6. Adjust to boost or cut HIGH frequencies.TREBLE KNOB:
7. Master Volume: Adjusts main audio system volume level.
8. Lets you connect the desired LINE input source.RCA L/R LINE Input:
9. Speaker output (L/R)
10. AC IN
11. Wireless BT Antenna: Wireless BT Streaming receiver
Rear PanelFront Panel
www.PyleUSA.com
3
Setup and pairing (Wireless BT ampliers) are really easy. The following
instructions will help you connect Audio Ampliers to your music system or
pair with your tablet, computer, or smartphone.
1. Connecting the Speaker Wire
Audio stereo power ampliers that will power one pair of passive speakers
between 4 and 8 ohms (or subwoofer if you got the 2.1 CH amp or subwoofer
amp). To connect the amplier to your speakers you will need 2-conductor
stranded speaker wire. The ampliers use high-quality binding posts that will
accept heavy gauge bare wire banana plugs, spade lugs, or pin terminators.
If you use your own speaker wire we recommend using at least 16 gauge wire
and using the same length of wire from the amplier to each speaker It's also a
good idea to turn o your amplier before connecting power, audio sources or
speakers.
Preparing the Speaker Wire
1. Separate the last 3" of each speaker wire conductor.
2. Strip 1/2" of insulation from the end of each wire.
3. Twist the exposed copper strands with your ngers 3 or 4 times so the strands
stay together.
NOTE:
As you make your connections, be sure to connect the positive (+) terminals on
your amplier to the positive (+) terminals on your speakers. Even if your wire does
not have (+) or (-) markings, most 2-conductor speaker wire has printing on one
side to help you dierentiate between the wire pairs.
If you are Using Bare Wire
1. Use your thumb and nger to unscrew the binding post connectors on the back
of each speaker.
2. Insert each speaker wire into the holes on the side of the binding post connectors,
observing proper polarity.
3. Retighten the binding posts with your ngers.
4. The stripped portion of the wire should be secured rmly in each connector.
5. Make sure that none of the speaker wire strands have come in contact with an
adjoining terminal.


Produktspezifikationen

Marke: Pyle
Kategorie: Empfänger
Modell: PDA30BU

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PDA30BU benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Empfänger Pyle

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-