Planet WGS-818HP Bedienungsanleitung

Planet Schalter WGS-818HP

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Planet WGS-818HP (4 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 8-Port 10/100/1000T

Wall-mounted Gigabit Ethernet Switch, WGS-803.

Open the box of the WGS-803 Gigabit Ethernet Switch

and carefully unpack it. The box should contain the

following items:

zThe WGS-803 Gigabit Ethernet Switch x 1

zUser Manual x 1

zDIN-rail Kit x 1

zWall-mounted Kit x 1

zMagnet Kit x 1

z3-pin Terminal Block Connector x 1

zRJ45 Dust-proof Cap x 8

If any item is found missing or damaged, please contact

your local reseller for replacement.

2.1 Terminal Block Connector Pinouts

To install the 3-pin Terminal Block Connector on the

WGS-803, simply follow the following steps:

Step 1: Insert positive DC power wire into V+,

negative DC power wire into , and grounding V-

wire into Ground.

Step 2: Tighten the wire-clamp screws for preventing

the wires from loosening and plug into the

wall-mounted switch.

Note

1. The wire gauge should be in the range

from 12 to 24 AWG

2. The device must be grounded

3. The DC power input range is 12V ~ 48V DC

2.2 LED Indicators

 System

LED Color Function

PWR Green Lights to indicate that the Switch has

power.

2.4 Physical Dimensions (WxDxH):

148 x 24.2 x 134mm

118.00

148.00 24.20

6.00

133.00

134.00

Dimensions ( unit = mm )

2.3 ProductSpecications

Model WGS-803

Hardware Specications

Network

Connector 8-port RJ45 for 10/100/1000BASE-T

MAC Address

Table

8K MAC address table with auto

learning function

Data Buffer 64Kbytes

Switch Fabric 16Gbps

Switch

Throughput 11.9Mpps@64bytes

Flow Control Back pressure for half duplex. IEEE

802.3x pause frame for full duplex

Power

Requirements 12~48V DC, 0.5A (max.)

Power

Consumption 6 watts/20BTU

ESD Protection 6KV DC

EFT Protection 6KV DC

Enclosure IP30 aluminum

2. Hardware Description

The front panel of the WGS-803 Gigabit Ethernet Switch

consists of 8 Auto-sensing 10/100/1000Mbps Ethernet

RJ45 Ports. The LED Indicators are also located on the

RJ45 ports of the Gigabit Ethernet Switch.

10/100/1000BASE-T RJ45 Port

3-pin Terminal Block

DC Plug-in

 10/100/1000BASE-T Interfaces

LED Color Function

LNK/

ACT Green

Lights

To indicate the link through

that port is successfully

established.

Blinks To indicate that the switch is

actively sending or receiving

data over that port.

1000 Green

Lights To indicate that the port is

operating at 1000Mbps.

Off If LNK/ACT LED is lit, it

indicates that the port is

operating at 10/100Mbps.

If LNK/ACT LED is Off, it

indicates that the port is link-

down.

3. Installation

3.1 Wall Mount Installation

To install the WGS-803 Gigabit Ethernet Switch on the

wall, simply follow the following steps:

Step 1: There are 4 holes with 8mm diameter on

the wall; the distance between the 2 holes is

133mm and the line through them must be

horizontal.

Step 2: Install a conductor pipe inside the board hole

and ush the edge of the conductor pipe with

the wall surface.

Step 3: Screw the bolts into the conductor pipe. The

WGS-803 is between bolts and conductor pipe,

as shown below.

Dimensions

(W x D x H) 148 x 24.2 x 134 mm

Weight 498g

Standard Conformance

Standard

Compliance

IEEE 802.3

IEEE 802.3u

IEEE 802.3ab

IEEE 802.3x

Ethernet

Fast Ethernet

Gigabit Ethernet

Flow Control

Regulatory

Compliance FCC Part 15 Class A, CE

Environment

Operating

Temperature: -10 ~ 60 degrees C

Relative Humidity: 5 ~ 95%

(non-condensing)

Storage

Temperature: -20 ~ 70 degrees C

Relative Humidity: 5 ~ 95%

(non-condensing)

- 9 -

- 10 -

- 11 -

- 12 -

3.2 DIN-rail Mounting Installation

The DIN-rail kit is included in the WGS-803 package.

When the wall-mount application for the WGS-803

needs to be replaced with DIN-rail application, please

refer to the following gures to screw the DIN-rail on

the WGS-803. To hang up the WGS-803, follow the

steps below:

Step 1: Screw the DIN-rail on the WGS-803

3.3 Magnet Installation

To install the WGS-803 on a magnetic surface, simply

follow the following diagram:

Step 2: Lightly insert the bottom of DIN-rail into the

track

1Push

2Click

Step 3: Check whether the DIN-rail is tightly on the

track

4. Customer Support

Thank you for purchasing PLANET products. You can

browse our online FAQ resource and User’s Manual on

PLANET Web site rst to check if it could solve your

issue. If you need more support information, please

contact PLANET switch support team.

PLANET online FAQ:

http://www.planet.com.tw/en/support/faq.php?type=1

Switch support team mail address:

support_switch@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All

other trademarks belong to their respective owners.

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

EC Declaration of Conformity

For the following equipment:

*Type of Product: Industrial 8-Port 10/100/1000T Wall-mount Switch

*Model Number: WGS-803

* Produced by:

Manufacturer‘s Name : Planet Technology Corp.

Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,

New Taipei City 231, Taiwan (R.O.C.)

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive

on (2004/108/EC).

For the evaluation regarding the EMC, the following standards were applied:

EN 55022 (2010)

EN 61000-3-2 (2006 + A2:2009)

EN 61000-3-3 (2008)

EN 55024 (2010)

EN 61000-4-2 (2009)

EN 61000-4-3 (2006 + A2:2010)

EN 61000-4-4 (2012)

EN 61000-4-5 (2006)

EN 61000-4-6 (2009)

EN 61000-4-8 (2010)

EN 61000-4-11 (2004)

Responsible for marking this declaration if the:

Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan

(R.O.C.)

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Product Manager

Taiwan 28th April, 2015

Place Date Legal Signature

Produktspezifikationen

Marke:	Planet
Kategorie:	Schalter
Modell:	WGS-818HP
Breite:	148 mm
Tiefe:	25 mm
Gewicht:	474 g
Höhe:	134 mm
Betriebstemperatur:	-20 - 60 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Netzstandard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Temperaturbereich bei Lagerung:	-20 - 70 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	8
Basic Switching RJ-45 Ethernet Ports-Typ:	Gigabit Ethernet (10/100/1000)
10G-Unterstützung:	Nein
Rack-Einbau:	Ja
Stapelbar:	Ja
Netzteil enthalten:	Nein