Planet ISW-504PT Bedienungsanleitung

Planet Schalter ISW-504PT

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Planet ISW-504PT (2 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 5-Port Industrial Ethernet

Switch with 4-Port PoE, ISW-504PT/ISW-514PTF. The interfaces

of these models are shown below:

Model Name 10/100Mbps RJ45

Ports 100FX SFP Slots PoE Ports

ISW-504PT 5 - 4

ISW-514PTF 4 1 4

In the following section, the term “Industrial PoE+ Switch”

means the ISW-504PT/ISW-514PTF.

2. Hardware Introduction

2.1 Switch Front Panel

P1 P2 Fault

120W

PoE Usage

90W

60W

30W

LNK ACT

PoE-in-Use

挖孔

10/100TX

LNK/

ACT

DIP

1~4

VLAN

Extended

OFF

Standard

1234 5

ONDIP

LNK ACT

PoE-in-Use

挖孔

P1 P2 Fault

100FX

DIP

1~4

VLAN

Extended

OFF

Standard

120W

PoE Usage

90W

60W

30W

1234 5

ONDIP

Figure 2-1:

ISW-504PT front panel

Figure 2-2:

ISW-514PTF front panel

1. Fast Ethernet TP Interfaces

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

2.3 Switch Upper Panel

The upper panel of the Industrial PoE+ Switch consists of one

terminal block connector within two DC power inputs.

Figure 2-3 shows the upper panel of the Industrial PoE+ Switch.

Input DC 12~48V

Fault max.

load 1A@24V

FaultDC1 DC2

1 2 3 4 5 6

Figure 2-3: Industrial PoE+ Switch Upper Panel

2.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial PoE+ Switch is used for two DC redundant power

inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like

inserting the wires or tightening the wire-clamp

screws, make sure the power is OFF to prevent

from getting an electric shock.

2.2 LED Indicators

System

LED Color Function

P1 Green Lights: indicates power 1 has power.

P2 Green Lights: indicates power 2 has power.

FAULT Red Lights: indicates either power 1 or power 2

has no power.

30W Amber

O: indicates the PoE usage is less than

14W.

Blinks: indicates that the PoE usage is

around 15W to 29W.

Lights: indicates the PoE usage is around/

over 30W.

60W Amber

Blinks: indicates that the PoE usage is

around 45W to 59W.

Lights: indicates the PoE usage is around/

over 60W.

90W Amber

Blinks: indicates that the PoE usage is

around 75W to 89W.

Lights: indicates the PoE usage is around/

over 90W.

120W Amber

Blinks: indicates that the PoE usage is

around 100W to 119W.

Lights: indicates the PoE usage is at the

maximum.

Open the box of the Industrial PoE+ Switch and carefully

unpack it. The box should contain the following items:

Industrial PoE+ Switch x 1 User’s Manual x 1

Dust Cap x 5 Wall-mount Kit x 1

If any of these are missing or damaged, please contact your

dealer immediately.

2. 100BASE-FX SFP Slot (ISW-514PTF)

100BASE-FX mini-GBIC slot, SFP (small form-factor plug-

gable) transceiver module: From 2 kilometers (multi-mode

ber) to 20/40/60 kilometers (single-mode ber).

3. DIP Switch

The Industrial PoE+ Switch provides one DIP switch for

Standard, VLAN and Extended mode selections. The

detailed descriptions are shown in the following table.

DIP Switch

Mode Function

Standard Switches 1 to 5 are o.

This mode makes the Industrial PoE+ Switch

operate as a general switch and all PoE ports

operate at 10/100Mbps auto-negotiation.

VLAN

Switch 5 is on.

This mode makes the Industrial PoE+ Switch

operate as a V andLAN isolation switch

1. Ports 1 to 4 will isolate respectively.

2. Ports 1 to 4 can only communicate with Port 5.

Note

After adjusting VLAN DIP switch,

reboot the Industrial PoE+ Switch to

make the change take effect.

Extended Any of switches 1 to 4 is on.

This mode makes the Industrial PoE+ Switch

operate on a per-port basis at 10Mbps full duplex

operation but can support IEEE 802.3af PoE power

output over a distance of up to 250 meters

overcoming the 100m limit on Ethernet UTP cable.

 Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1

to Port 4)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port

is successfully established at 10Mbps or

100Mbps.

Blinking: indicates that the switch is

actively sending or receiving data over that

port.

PoE-

in-Use Amber

Lights: indicates the port is providing DC

in-line power.

O: indicates the connected device is not a

PoE powered device (PD).

 Per 10/100BASE-TX Interface (Port 5 of ISW-504PT)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is

successfully established at 10/100Mbps.

Blinking: indicates that the switch is actively

sending or receiving data over that port.

 Per 100FX SFP Slot (Port 5 of ISW-514PTF)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is

successfully established at 100Mbps.

Blinks: indicates that the switch is actively

sending or receiving data over that port.

1. The DC power input range is . Please insert 12V ~ 48V DC

positive and negative DC power wires into contacts 1 and 2

for POWER 1, or 5 and 6 for POWER 2.

Input DC 12~48V

Fault max.

load 1A@24V

FaultDC1 DC2

1 2 3 4 5 6

DC Input Max. PoE Budget

12V 60W

24V 90W

48V 120W

Note

To avoid damage, please use the Industrial PoE+

Switch under its specification.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

Note

The wire gauge for the terminal block should be in

the range between 12 and 24 AWG.

2.5 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. Inserting the wires,

the Industrial PoE+ Switch will detect the fault status of the

power failure and then forms an open circuit. The following

illustration shows an application example for wiring the fault

alarm contacts.

3. Installation

This section describes the functionalities of the Industrial PoE+

Switch’s components and guides you to installing it on the

DIN-rail and wall. Basic knowledge of networking is assumed.

Please read this chapter completely before continuing.

Note

The installation procedures of the ISW-504PT and

ISW-514PTF are the same as they are shown

below.

3.1 DIN-rail Mounting Installation

1 2 3 4 5 6

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be

in the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V, max. 1A

currents.

2.6 Grounding the Device

Uses MUST complete grounding wired with the device;

otherwise, a sudden lightning could cause fatal damage to the

device. EMD (Lightning) DAMAGE IS NOT CONVERED UNDER

WARRANTY.

3.2 Wall-mount Plate Mounting

3.3 Side Wall-mount Plate Mounting

4. Troubleshooting

This chapter contains information to help you solve issues. If

the Industrial PoE+ Switch is not functioning properly, make

sure the Industrial PoE+ Switch was set up according to

instructions in this manual.

 What is the operating temperature of the device?

Solution:

The operating temperature is from -40 to 75 degrees C.

 What is the IP code of the device?

Solution:

The device has a rugged IP40 metal housing

 Per port LED is lit, but the trac is irregular

Solution:

Check whether the attached device is not set to dedicated full

duplex. Some devices use a physical or software switch to

change duplex modes. Auto-negotiation may not recognize this

type of full-duplex setting.

 Why the Industrial PoE+ Switch doesn’t connect to

the network

Solution:

Check each port LED on the Industrial PoE+ Switch. Try

another port on the Industrial PoE+ Switch. Make sure the

cable is installed properly and the right type. Turn o the

power. After a while, turn on the power again.

 I connected a PoE powered device to the Industrial

POE+ Switch, why it could not be powered on

Solution:

1. Please check the cable type of the connection from

Industrial POE+ Switch (port 1 to port 4) to the other

end. The cable should be an 8-wire UTP, Category 5e

or above, EIA568 cable within 100 meters. A cable with

only 4-wire, short loop or over 100 meters will aect the

power supply.

2. Please check and assure the PoE powered device is fully

complied with IEEE 802.3at standard.

5. Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource at the PLANET Web site rst to

check if it could solve your issue. If you need more support

information, please contact PLANET support team.

PLANET online FAQs:

https://www.planet.com.tw/en/support/

faq?method=category&c1=3

Support team mail address:

support@planet.com.tw

Produktspezifikationen

Marke:	Planet
Kategorie:	Schalter
Modell:	ISW-504PT
Breite:	50 mm
Tiefe:	85.1 mm
Gewicht:	596 g
Produktfarbe:	Schwarz
Internationale Schutzart (IP-Code):	IP30
Höhe:	135 mm
Energieschutzeigenschaften:	Kurzschluß
Betriebstemperatur:	-40 - 75 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Netzstandard:	IEEE 802.3af, IEEE 802.3u, IEEE 802.3x
Zertifizierung:	FCC, CE
Vollduplex:	Ja
Power over Ethernet (PoE):	Ja
Warentarifnummer (HS):	85176990
Gehäusematerial:	Metall
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-40 - 85 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Switch-Typ:	Unmanaged
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	5
Basic Switching RJ-45 Ethernet Ports-Typ:	Fast Ethernet (10/100)
Auto MDI/MDI-X:	Ja
10G-Unterstützung:	Nein
MAC-Adressentabelle:	1024 Eintragungen
Routing-/Switching-Kapazität:	1 Gbit/s
Durchgang:	0.74 Mpps
Rack-Einbau:	Nein
Wandmontage:	Ja
Store-and-Forward:	Ja
Stapelbar:	Ja
Auto-Negotiation-Funktion:	Ja
unterstütze Kabeltypen:	Cat5, Cat5e, Cat6
Unterstützung Datenflusssteuerung:	Ja
Netzteil enthalten:	Nein
Switch-Ebene:	L2
Unterstützung für redundantes Netzteil:	Ja
Anzahl Power over Ethernet (PoE) Anschlüsse:	4
Selbstlernen von MAC-Adressen unterstützt:	Ja
Auto-Alterung von MAC-Adressen unterstützt:	Ja
Power over Ethernet (PoE) Leistung pro Anschluss:	15.4 W
DIN-Schienen-Montage:	Ja