Planet ISW-1600T Bedienungsanleitung

Planet Schalter ISW-1600T

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Planet ISW-1600T (2 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

Industrial Multi-port 10/100TX

Fast Ethernet Switch

ISW-1600T/IFGS-1822TF

Version 1.0

User's Manual

2.ProductSpecications

Product ISW-1600T IFGS-1822TF

Hardware Specications

Fast Ethernet

Copper Ports

16 10/100BASE-TX RJ45 auto-MDI/MDI-X

ports

Gigabit Ethernet

Copper Ports --

Two

10/100/1000BASE-T

RJ45 auto-MDI/MDI-X

ports

(shared with Port-17

and Port-18)

SFP Slots --

Two 1000BASE-SX/

LX/BX SFP interfaces

(shared with Port-17

and Port-18)

Switch Architecture Store-and-Forward

Switch Fabric 3.2Gbps

(non-blocking)

7.2Gbps

(non-blocking)

Throughput

(packet per

second)

2.38Mpps@ 64 bytes 5.36Mpps@ 64 bytes

Address Table 16K entries, automatic source address

learning and aging

Shared Data Buer 4Mbits

3.2 LEDDenition:

 System

LED FunctionColor

DC1 Lights to indicate DC power input 1 has power.Green

DC2 Lights to indicate DC power input 2 has power.Green

Fault Red Lights to indicate that AC or DC power has

failed.

 Per 10/100BASE-TX Port

LED FunctionColor

LNK/

ACT Green

Lights to indicate the link through that port is

successfully established.

Blinking to indicate that the switch is actively

sending or receiving data over that port.

O to indicates that the port is linked down.

100

Speed Amber

Lights to indicate that the port is operating at

100Mbps.

O to indicates that the port is operating at

10Mbps.

O to indicates that the port is linked down.

Standards

Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u

100BASE-TX

IEEE 802.3x ow

control and back

pressure

IEEE 802.1p Class of

Service

IEEE 802.3az Energy

Ecient Ethernet

(EEE)

IEEE 802.3 10BASE-T

IEEE 802.3u

100BASE-TX

IEEE 802.3ab Gigabit

1000T

IEEE 802.3z Gigabit

SX/LX

IEEE 802.3x ow

control and back

pressure

IEEE 802.1p Class of

Service

IEEE 802.3az Energy

Ecient Ethernet

(EEE)

Environment

Operating

Temperature -40 ~ 75 degrees C

Storage

Temperature -40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

1. Package Contents

Thank you for purchasing PLANET Industrial Multi-port 10/100TX

Fast Ethernet Switch, ISW-1600T/IFGS-1822TF. In the following

sections, the term means the “Industrial Ethernet Switch”

ISW-1600T or IFGS-1822TF.

Open the box of the Industrial Ethernet Switch and carefully

unpack it. The box should contain the following items:

Industrial Ethernet

Switch x 1

User’s Manual x 1 Wall-mount Kit x 1

RJ45 Dust Cap x 16 DIN-rail Kit SFP Dust Cap x 2

(IFGS-1822TF only)

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original

packing material, and use them again to repack the product in case

there is a need to return it to us for repair.

Flow Control IEEE 802.3x pause frame for full-duplex

Back pressure for half-duplex

ESD Protection 6KV DC

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

Connector

Removable 6-pin terminal block for power

input

Pin 1/2 for Power 1, Pin 3/4 for fault alarm,

Pin 5/6 for Power 2

Alarm One relay output for power failure. Alarm

relay current carry ability: 1A @ 24V DC

Dimensions

(W x D x H) 66 x 107 x 152 mm 66 x 107 x 152 mm

Weight 255g 300g

Power

Requirements Dual 12~48V DC, 24V AC

Power

Consumption

Max. 5.3

watts/18BTU

(Ethernet full

loading)

Max. 6.3

watts/21.4BTU

(Ethernet full

loading)

Standards Conformance

Regulatory

Compliance FCC Part 15 Class A, CE

Stability Testing

IEC60068-2-32 (free fall)

IEC60068-2-27 (shock)

IEC60068-2-6 (vibration)

3. Hardware Introduction

3.1 Switch Front Panel

The front panel of the consists of Industrial Ethernet Switch

Ethernet interfaces and LED indicators.

 Front View

P1 P2 Fau lt

ACTLNK

100

P1 P2 Fau lt

1000X

1000T

ACTLNK

1000

ACTLNK

100

Figure1:

ISW-1600T Front View

Figure2:

IFGS-1822TF Front View

 Per Gigabit RJ45/SFP Combo Interface

(Port-17~Port-18 of IFGSW-1822TF)

LED FunctionColor

LNK/

ACT Green

Lights to indicate the link through that port is

successfully established.

Blinking to indicate that the switch is actively

sending or receiving data over that port.

O to indicates that the port is linked down.

1000

Speed Amber

Lights to indicate that the port is operating at

1000Mbps.

O to indicates that the port is operating at

10/100Mbps.

O to indicates that the port is linked down.

3.3 Switch Upper Panel

The upper panel of the Industrial Ethernet Switch consists of one

terminal block connector within two power input and one relay

ouput.

Max. fault loading: 24V, 1A

V1+ V1- V2+ V2-

PWR1 PWR2Fault

DC Input: 12-48V

, 2A max.

AC Input: 24V

, 1A max.

1 2 3 4 5 6

Figure3: ISW-1600T and IFGS-1822TF Top View

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

3.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial Ethernet Switch is used for two DC redundant power

inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like inserting

the wires or tightening the wire-clamp screws, make

sure the power is OFF to prevent from getting an

electric shock.

1. Insert positive and negative DC power wires into contacts 1 and

2 for POWER 1, or contacts 5 and 6 for POWER 2.

Max. fault loading: 24V, 1A

V1+ V1- V2+ V2-

PWR1 PWR2Fault

DC Input: 12-48V

, 2A max.

AC Input: 24V

, 1A max.

1 2 3 4 5 6

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 64 5

Power 1 Fault Power 2

+ - + -

4. Installation

This section describes the functionalities of the Industrial Ethernet

Switch’s components and guides you to installing it on the DIN rail

and wall. Please read this chapter completely before continuing.

Note

This following pictures show how to install the device.

However, the device in the picture is not ISW-1600T

or IFGS-1822TF.

4.1 DIN-rail Mounting Installation

Note

1. The wire gauge for the terminal block should be in

the range between 12 and 24 AWG.

2. The power input range is 12V ~ 48V DC and

supports 24V AC.

3. Use one power input when using 24V AC.

3.5 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. Inserting the wires, the

Industrial Ethernet Switch will detect the fault status of the power

failure and then forms an open circuit. The following illustration

shows an application example for wiring the fault alarm contacts.

123456

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be in

the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V DC,1A

4.2 Wall-mount Plate Mounting

4.3 Side Wall-mount Plate Mounting

5. Customer Support

Thank you for purchasing PLANET products. You can browse our

online FAQ resource on PLANET web site rst to check if it could

solve your issue. If you need more support information, please

contact PLANET switch support team.

PLANET online FAQ:

http://www.planet.com.tw/en/support/faq

Switch support team mail address:

support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

FCC Warning

This equipment has been tested and found to comply with the

regulations for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed

and used in accordance with this user’s guide, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at his own

expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product

may cause radio interference, in which case the user may be

required to take adequate measures.

WEEE Warning

To avoid the potential eects on the environment and

human health as a result of the presence of hazardous

substances in electrical and electronic equipment, end

users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do

not dispose of WEEE as unsorted municipal waste and have to

collect such WEEE separately.

Produktspezifikationen

Marke:	Planet
Kategorie:	Schalter
Modell:	ISW-1600T
Breite:	66 mm
Tiefe:	107 mm
Gewicht:	750 g
Produktfarbe:	Blau
Internationale Schutzart (IP-Code):	IP30
Höhe:	152 mm
Betriebstemperatur:	-40 - 75 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Netzstandard:	IEEE 802.3, IEEE 802.3az, IEEE 802.3p, IEEE 802.3u, IEEE 802.3x
Power over Ethernet (PoE):	Nein
Stromverbrauch (max.):	5.3 W
Gehäusematerial:	Metall
Temperaturbereich bei Lagerung:	-40 - 85 °C
Switch-Typ:	Unmanaged
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	16
Basic Switching RJ-45 Ethernet Ports-Typ:	Fast Ethernet (10/100)
Auto MDI/MDI-X:	Ja
10G-Unterstützung:	Nein
Kupfer Ethernet Verkabelungstechnologie:	10BASE-T, 100BASE-TX
MAC-Adressentabelle:	16000 Eintragungen
Routing-/Switching-Kapazität:	3.2 Gbit/s
Durchgang:	2.38 Mpps
Rack-Einbau:	Nein
Wandmontage:	Ja
Store-and-Forward:	Ja
Stapelbar:	Nein
Unterstützung Datenflusssteuerung:	Ja
Netzteil enthalten:	Nein
DIN-Schienen-Montage:	Ja
Fast Ethernet (Kupfer)-Anschlüsse:	16