PeakTech 6181 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PeakTech 6181 (26 Seiten) in der Kategorie Messung. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/26
Operation manual
Programmable linear laboratory power supply
PeakTech®
Table of contents
Topic
Page
1.
Safety instructions for operating the device
1
2.
Introduction
2
3.
Quick start
3
3.1.
Front/rear panel and user interface
4
3.1.1.
Front
3.1.2.
Back
5
3.1.3.
User interface
6
3.2.
General inspection
7
3.3.
Switch-on control
7
3.4.
Output control
7
3.4.1.
Voltage output test
3.4.2.
Current output test
8
4.
Controls on the front panel
4.1.
Enable/disable the outputs
4.2.
Set output voltage and current
4.3.
Overvoltage and overcurrent protection
9
4.3.1.
Set overvoltage protection value
4.3.2.
Set overcurrent protection value
10
4.4.
Programmable output
11
4.4.1.
Data view
4.4.2.
Output settings
4.4.3.
Data Process
12
4.4.4.
Enable/disable programmable output
13
4.5.
Save settings and Auto record
4.5.1.
Save settings
4.5.2.
Auto Record
14
4.5.3.
View Record
4.6.
Output mode
15
4.7.
Utility (System) - Settings
18
4.7.1.
Select language
4.7.2.
Brightness
4.7.3.
Summer
4.7.4.
Time
4.8.
System information
4.8.1.
Show system information
4.8.2.
Default settings
4.8.3.
Update
19
4.9.
Port settings
4.9.1.
Serial interface
4.9.2.
Lan interface
20
4.9.3.
LCD test
4.9.4.
Keys test
5.
Troubleshooting
21
6.
Technical specications
22
7.
Appendix
23
1 safety instructions for operating the device .
This product complies with the requirements of the following European Union Directives for CE conformity: 2014/30/EU
(Electromagnetic Compatibility), 2014/35/EU (Low Voltage), 2011/65/EU (RoHS).
To ensure the operational safety of the device and to avoid serious injuries due to current or voltage ashovers or short
circuits, the following safety instructions for operating the device must be observed.
Damages caused by non-observance of these instructions are excluded from claims of any kind.
ï‚· This device must not be used in high energy circuits.
ï‚· Before connecting the device to a power outlet, check that the voltage setting on the device matches the existing
mains voltage
ï‚· Connect the device only to sockets with grounded protective conductor
ï‚· Do not place the device on a damp or wet surface.
ï‚· Check the device, test leads and other accessories for possible damage or bare or kinked cables and wires before
commissioning. If in doubt, do not carry out any measurements
ï‚· Replace defective fuses only with a fuse corresponding to the original value. Never short-circuit the fuse or fuse
holder.
ï‚· It is essential to keep the ventilation slots in the housing free (if covered, there is a risk of heat accumulation inside
the device).
ï‚· Do not insert any metal objects through the ventilation slots.
ï‚· Do not place any liquids on the device (risk of short circuit if the device tips over).
 Do not operate the device near strong magnetic elds (motors, transformers, etc.)
ï‚· Never operate the device if it is not completely closed.
ï‚· Use only 4mm safety test cable sets to ensure proper functioning of the device.
ï‚· Only carry out measurement work in dry clothing and preferably in rubber shoes or on an insulating mat.
ï‚· It is essential to observe the warnings on the device.
ï‚· Device must not be operated unattended
ï‚· Do not expose the device to extreme temperatures, direct sunlight, extreme humidity or moisture.
ï‚· Avoid strong vibration.
ï‚· Keep hot soldering guns away from the immediate vicinity of the device.
ï‚· Before starting the measuring operation, the device should be stabilized to the ambient temperature (important
when transporting from cold to warm rooms and vice versa)
ï‚· Clean the housing regularly with a damp cloth and a mild cleaning agent. Do not use any corrosive scouring agents.
ï‚· This device is suitable for indoor applications only.
 Avoid any proximity to explosive and ammable substances.
 Opening of the device and maintenance and repair work may only be carried out by qualied service technicians.
ï‚· Do not place the device with its front side on the workbench or work surface to avoid damage to the controls.
 Do not make any technical modications to the device.
ï‚· -Measuring instruments do not belong in children's hands-
Cleaning of the device:
Before cleaning the device, disconnect the power plug from the socket. Clean the device only with a damp, lint-free cloth.
Use only commercially available detergents. When cleaning, make absolutely sure that no liquid gets into the interior of the
device. This could lead to a short circuit and destruction of the device.
-1-
Produktspezifikationen
| Marke: | PeakTech |
| Kategorie: | Messung |
| Modell: | 6181 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit PeakTech 6181 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Messung PeakTech
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
16 Juni 2024
Bedienungsanleitung Messung
- Messung Hama
- Messung REV
- Messung Voltcraft
- Messung Bosch
- Messung Laserliner
- Messung Velleman
- Messung Powerfix
- Messung Alecto
- Messung Beurer
- Messung Bresser
- Messung König
- Messung TFA
- Messung Black And Decker
- Messung Trotec
- Messung DeWalt
- Messung Pioneer
- Messung Megasat
- Messung Smartwares
- Messung Garmin
- Messung GOCLEVER
- Messung Perel
- Messung Workzone
- Messung Microlife
- Messung Rossmax
- Messung Amprobe
- Messung Meec Tools
- Messung Metrix
- Messung IHealth
- Messung Ansmann
- Messung Westfalia
- Messung Livington
- Messung Silverline
- Messung Yato
- Messung Be Cool
- Messung Toolland
- Messung AS Schwabe
- Messung Hager
- Messung Kyoritsu
- Messung Eurolite
- Messung GW Instek
- Messung KERN
- Messung Milwaukee
- Messung Eizo
- Messung Testo
- Messung Victron Energy
- Messung Peak
- Messung Kübler
- Messung Carrier
- Messung Lund
- Messung SHX
- Messung Gima
- Messung Testboy
- Messung Danfoss
- Messung Fantini Cosmi
- Messung Multimetrix
- Messung Extech
- Messung BENNING
- Messung Fluke
- Messung FLIR
- Messung Vemer
- Messung Oregon Scientific
- Messung Ridgid
- Messung Stabila
- Messung Hikmicro
- Messung Entes
- Messung Gossen Metrawatt
- Messung Hameg
- Messung Joy-it
- Messung Megger
- Messung Muller
- Messung PCE Instruments
- Messung RK Technology
- Messung Sanwa
- Messung Sonel
- Messung Uni-T
- Messung VirtuFit
- Messung Wachendorff
- Messung TFA Dostmann
- Messung Vimar
- Messung Owon
- Messung Comark
- Messung Dahua Technology
- Messung YSI
- Messung Aluratek
- Messung SRS
- Messung Eltako
- Messung H-Tronic
- Messung HT Instruments
- Messung Beha-Amprobe
- Messung Chauvin Arnoux
- Messung Werma
- Messung Eastron
- Messung Emko
- Messung Pancontrol
- Messung X-Rite
- Messung CESYS
- Messung Trumeter
- Messung Kemo
- Messung ORNO
- Messung Tempest
- Messung TDE Instruments
- Messung Zircon
- Messung Kreg
- Messung Apollo Ultrasonic
- Messung BJZ
- Messung Adwa
- Messung Greisinger
- Messung Qubino
- Messung Beckmann & Egle
- Messung Weidmüller
- Messung Janitza
- Messung CEM
- Messung Klein Tools
- Messung Daytronic
- Messung AREXX
- Messung Delta Ohm
- Messung Camille Bauer
- Messung Rigel Medical
- Messung UHoo
- Messung Seaward
- Messung AstroAI
- Messung P3 International
- Messung Seek Thermal
- Messung ClimeMET
- Messung Fixpoint
- Messung Condtrol
- Messung Cliff
- Messung Water-i.d.
- Messung Stahlwille
- Messung KS Tools
- Messung AkYtec
Neueste Bedienungsanleitung für -Kategorien-
4 August 2024
24 Juni 2024
24 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
22 Juni 2024
21 Juni 2024
21 Juni 2024