Panasonic WV-SFR311A Bedienungsanleitung

Panasonic Sicherheitskamera WV-SFR311A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Panasonic WV-SFR311A (4 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

WV-SFN311A

(This illustration represents WV-SFN311A.)

● This manual describes the installation procedures, network camera installation, cable connections,

and the angle of view adjustment.

● Before reading this manual, be sure to read the Important Information.

● This manual describes how to install the network camera using model WV-SFN311A as an example.

PGQX1950ZA es0915-0 Printed in China

Important Information ............................... 1 pc.

Installation Guide (this document) ............ 1 set

Warranty card ........................................... 1 set

CD-ROM*1 ................................................ 1 pc.

Code label*2 .............................................. 1 pc.

*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. The network administrator shall retain the

code label.

The following parts are used during installation procedures.

Ⓐ Attachment plate .................................. 1 pc.

ⒷBit (Hex wrench, screw

size 6.35 mm {1/4 inches} T10) ............... 1 pc.

Ⓒ

Template A (for the attachment plate)

...... 1 sheet

Ⓓ Power cord plug*3 ................................ 1 pc.

Ⓔ External I/O terminal plug*3 .................. 1 pc.

Ⓕ MONITOR OUT conversion plug ......... 1 pc.

Ⓖ Auxiliary handle ................................... 1 pc.

Azimuth adjustment ring

The component names of the camera are as follows. Refer to the illustration when installing or

adjusting the camera.

*1 SDXC/SDHC/SD memory card is described as SD memory card.

*2 Depending on the scanning application used, the Data Matrix may not be able to be read

correctly. In this case, access the site by directly entering the following URL.

http://security.panasonic.com/pss/security/support/qr_sp_select.html

Turn off each system’s power supply before making a connection. Before making connections,

prepare the required peripheral devices and cables.

Connect the output cable to the power cord plug ( : accessory).Ⓓ

Before starting the installation, check the entire system configuration. The following illustration

gives a wiring example of how to connect the camera to the network via a PoE device (hub).

*1 Recommended cable length from the speaker : less than 10 m {32.8 feet}

Recommended cable length from the microphone : less than 1 m {3.28 feet}

● Since the connector storage section

does not have a sufficient space, use

audio cables and an Ethernet cable

that do not exceed the sizes described

in the illustrations.

● Off, input, and output of the external I/O terminal 2 and 3 can be switched by con-

figuring the setting. Refer to the operating instructions on the provided CD-ROM for

further information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings

(“Off”, “Alarm input”, “Alarm output” or “AUX output”).

● Connect/disconnect the audio cables and turn on the power of the camera after turning

off the power of the audio output devices. Otherwise, loud noise may be heard from

the speaker.

● Make sure that the stereo mini plug is connected to this cable. When a monaural mini

plug is connected, audio may not be heard.

When connecting a monaural speaker with amplifier, use a locally procured conversion

cable (mono-stereo).

SFR311 SFN311

Connect a stereo mini plug (ø3.5 mm).

● Output impedance : Approx. 600 Ω (unbalanced)

● Recommended cable length : Less than 10 m {32.8 feet}

● Output level : –20 dBV (Can switch to monitor output)

SFR311 SFN311

Connect a stereo mini plug (ø3.5 mm).

● Input impedance: Approx. 2 kΩ (unbalanced)

● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)

Less than 10 m {32.8 feet} (for line input)

● Recommended microphone: Plug-in power type (option)

● Supply voltage: 2.5 V ±0.5 V

● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)

● Input level for the line input: Approx. –10 dBV

● Do not connect 2 wires or more directly to a terminal. When it is necessary to connect

2 or more wires, use a splitter.

● Install external devices so that they do not exceed the rating of the network camera.

● When using the EXT I/O terminals as the output terminals, ensure they do not

cause signal collision with external signals.

Ethernet cable (category 5e or better, straight)

Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.

● The adjustment monitor is used for checking the adjustment of the angular field of

view when installing the camera or when servicing. It is not provided for recording/

monitoring use.

● Depending on the monitor, some characters (camera title, preset ID, etc.) may not

be displayed on the screen.

● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.

● If a PoE hub is not used, each network camera must be connected to a 12 V DC

power supply.

● When using 12 V DC, power supply from a PoE hub or router is not required.

● Use all 4 pairs (8 pins) of the Ethernet cable.

● The maximum cable length is 100 m {328 feet}.

● Make sure that the PoE device in use is compliant with IEEE802.3af standard.

● When connecting both the 12 V DC power supply and the PoE device for power

supply, 12 V DC will be used for power supply.*

* If a 12 V DC power supply and a PoE hub or router are used at the same time,

network connections may not be possible. In this case, disable the PoE settings.

Refer to the operating instructions of the PoE hub or router in use.

* In the situation where a 12 V DC power supply and a PoE hub or router are used at

the same time and the 12 V DC power supply is then disconnected, the power

supply is stopped and the camera will restart.

● When the Ethernet cable is disconnected once, reconnect the cable after around

2 seconds. When the cable is quickly reconnected, the power may not be supplied

from the PoE device.

* Use an Ethernet cable (category 5e or better, 8 pins, straight).

Connect the cables of external devices to the External I/O terminal plug ( : accessory).Ⓔ 

q When connecting an external device, strip 8 mm - 9 mm {5/16 inches - 11/32 inches} of the

outer jacket of the cable and twist the cable core to prevent the short circuit first.

Specification of cable (wire): AWG20 - AWG26, Single core, twisted

w Push down the button of the desired terminal on the external I/O terminal plug with a ball-

point pen, and release the button when the cable of the external device is fully inserted

into the terminal hole.

● Check whether the stripped part of the wire is not exposed and is securely connected.

● ALARM IN1 (DAY/NIGHT IN, Auto time adjustment) SFR311 SFN311 , ALARM IN1 (Auto

time adjustment) SFN310SFR310 , ALARM IN2, ALARM IN3

Input specication : No-voltage make contact input (4 V - 5 V DC, internally pulled up)

OFF : Open or 4 V - 5 V DC

ON : Make contact with GND (required drive current: 1 mA or more)

● ALARM OUT, AUX OUT

Output specication

: Open collector output (maximum applied voltage: 20 V DC)

Open : 4 V - 5 V DC by internal pull-up

Close : Output voltage 1 V DC or less (maximum drive current: 50 mA)

* The default of EXT I/O terminals is “Off”.

● The 12 V DC power supply shall be insulated from the commercial AC power.

● Be sure to use the power cord plug ( : accessory) provided with this product.Ⓓ

● Be sure to fully insert the power cord plug ( : accessory) into the 12 V DC power Ⓓ

supply terminal. Otherwise, it may damage the camera or cause malfunction.

● When installing the camera, make sure that excessive force is not applied to the

power cable.

●

Be sure to use an AC adaptor compliant with the Specifications (written in the indication

label on the bottom side of this unit) regarding power source and power consumption.

● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED

TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or

LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).

q Loosen the screw of the power cord plug, strip 3 mm to 7 mm {1/8 inches to 9/32 inches}

from the end of the wire, twist the stripped part of the wire sufficiently to avoid short circuit,

and then connect the output cable to the power cord plug.

w Tighten the screw of the power cord plug. (Recommended tightening torque: 0.34 N·m

{0.25 lbf·ft})

● Check whether the stripped part of the wire is not exposed and is securely connected.

●

When connecting an external power supply to the camera, use the AWG16 to AWG24

single-wired or stranded wired cables.

ⒹⒺ

4321

Ⓑ

(Hex wrench, screw

size 6.35 mm

{1/4 inches} T10)

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic System Networks Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

*3 The external I/O terminal plug and power cord plug are attached to the camera.

4321

SFR311 SFN311

Ⓔ:

● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second) to

switch the output signal of the MONITOR OUT terminal (NTSCPAL output), the MONITOR

OUT terminal can be switched for the NTSC monitor/PAL monitor.

●

When the camera is initialized, the settings including the network settings will be initialized.

Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.

● Before initializing the settings, it is recommended to write down the settings in advance.

● Do not turn off the power of the camera during the process of initialization. Otherwise, it

may fail to initialize and may cause malfunction.

● How to initialize the camera

Follow the steps below to initialize the network camera.

Turn off the power of the camera. When using a PoE hub, disconnect the Ethernet cable from the

camera. When using an external power supply, disconnect the power cable connector of the camera.

Turn on the power of the camera while holding down the INITIAL SET button, and keep the INITIAL SET button

held down till the SD MOUNT indicator is lit in green (more than 10 seconds). In about 2 minutes after releasing

the INITIAL SET button, the camera will start up and the settings including the network settings will be initialized.

INITIAL SET button (Initializing / NTSC PAL switch button)

● When an SD memory card is inserted and could Lights off → Blinks green →

be recognized Lights off

● When data can be saved after the SD memory card is Lights off → Lights green

inserted and the SD ON/OFF button is pressed

(less than 1 second)

● When data can be saved to the SD memory card Lights green

● When the SD memory card is removed after holding

Lights green → Blinks green →

down the SD ON/OFF button (about 2 seconds)

Lights off (recording)

Lights green → Lights off

(waiting for recording)

●

When data cannot be saved to the SD memory card because

Lights off

an abnormality was detected or the SD memory card is

configured not to be used

● Lighting/blinking LED can be turned off with the software settings at any time. (The initial

state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the

installation conditions. (☞ Operating instructions included in the CD-ROM)

SD MOUNT indicator

q When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights

up in green and data can be saved to the SD memory card*1.

w When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights

off and the SD memory card can be removed.

SD ON/OFF button

●

When the camera is able to communicate with the connected device

Lights orange

LINK indicator

● When data is being sent via the network camera Blinks green (accessing)

ACT indicator

Powered speaker

Adjustment monitor PoE device (hub)

Ethernet cable

(category 5e or better, straight)

Ethernet cable

(category 5e or

better, straight)

Ethernet cable

(category 5e or better, straight)

Adjustment monitor

Microphone

Powered speaker

Microphone

● When AF (Auto Focus) operation is being executed Blinks red (1 time/second)

● When the set is being started Lights red

● When an SD memory card is recognized normally Lights red → Lights off

● When an abnormality is detected in the SD memory card Lights red → Stays red

or the SD memory card slot is not used after

the camera has started.

SD ERROR/AF indicator

WV-SFR311A / WV-SFR310A

WV-SFN311A / WV-SFN310A

Pan table fixing screw with washer

Auto focus (AF) button

MONITOR OUT

terminal (factory

shipment: NTSC

monitor)

Direction marker for installation (TOP )

Screen display

top (TOP)

SD memory card*1 slot

● Points up when installing to a wall.

Panning table

Enclosure Camera

Attachment plate

( : accessory)Ⓐ

External I/O terminal plug ( : accessory)Ⓔ

Inner

cover

Dome cover

Camera xing screw

Tilting table

Ⓖ

Zoom knob

Auxiliary

handle

* Route the power cable as

shown in the following

illustration, and do not clip

the power cable when

mounting the enclosure.

● As necessary, use a

cable tie (locally

procured) to tie the

cables together.

Direction marker for installation (FRONT ) SFN310

SFN310

Built-in microphone port

SFR311

SFN311

SFR311

SFN311

Power cord plug

(Ⓓ: accessory)

12 V DC power

supply terminal

WV-SFN311A

Built-in microphone

SFN310

Two-dimensional

barcode (Data

Matrix): To our

website*2

Direction marker

for installation

(FRONT )

SFN311 SFR311

SFR310

ø25.4 mm

{1 inch}

ø73 mm

{2-7/8 inches}

FRONT

46 mm {1-13/16 inches}

83.5 mm

{3-9/32 inches}

The installation tasks are explained using 5 steps.

Preparations Fixing the attachment plate Mount the camera to the

attachment plate

Adjustment



There are 4 methods to install the camera to a ceiling or wall as described below. Prepare the

required parts for each installation method before starting the installation. The following are the

requirements for the various installation methods.

(1) Mount the camera on the two-gang junction box using

the attachment plate ( : accessory).Ⓐ M4 screws x 4 196 N {44 lbf}

(2) Directly mount the camera onto the ceiling or wall us-

ing the attachment plate (when wiring can be installed

in the ceiling or wall).

M4 screws x 4 196 N {44 lbf}

(3) Mount the camera in the ceiling using WV-Q174B ceil-

ing mount brackets (approx. 280 {0.62 lbs}).*g 1*2—

There is suf-

cient strength in

the ceiling

(4) When mounting the camera on an insufciently strong

ceiling using the WV-Q105A ceiling mount brackets

(approximately 150 {0.33 lbs})*g 1

anchor bolts x 2 *3

*1 For information on mounting the camera using (3) WV-Q174B or (4) WV-Q105A, refer to

the Instruction Manual provided with the (3) WV-Q174B or (4) WV-Q105A.

*2 When using WV-Q174B camera ceiling mount bracket, if the built-in microphone port is blocked

by the cover of bracket, the collectable volume may decrease and the sound of attic is likely to

be collected by mistake. Therefore, please conrm the installation conditions before use.

*3 Make sure that the installed ceiling can support more than 5 times of the weight of the

camera, the attachment plate and the anchor bolt.

● Procure 4 screws (M4) to secure the attachment plate (Ⓐ: accessory) to a ceiling or a wall.

● The minimum required pull-out capacity of a single screw or anchor bolt is 196 N

{44 lbf} or more when mounting with the installation method (1) and (2) above.

●

When mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for securing.

(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})

● Select screws according to the material of the ceiling that the camera will be mounted

to. In this case, wood screws and nails should not be used.

● If a ceiling board such as plaster board is too weak to support the total weight, the

area shall be sufficiently reinforced.

Camera fixing screw

Attachment mounting

screws

Attachment plate

( : accessory)Ⓐ

The following are descriptions for when the camera with default settings is configured. If you are using fire-

wall software on your PC, the Setup Program may not be able to find any cameras on your network.

Configure the setting of the camera after temporarily invalidating the firewall software. Contact the network

administrator or your Internet service provider for information about configuring the settings of the network.

q Insert the provided CD-ROM into the CD-ROM drive of your PC.

w Click the [Run] button next to [IP Setting Software].

[Panasonic IP Setting] screen will be displayed. When a camera is found, information

about it, such as its MAC address and IP address, is displayed.

e Select the camera you want to congure, and click [Access Camera].

● Depending on the adjustable range or the optical zoom, it must be noted that the

shadow of the enclosure may be projected.

● When mounting the camera on a ceiling, adjust the tilt angle so that the TOP mark

above the lens always comes to the top side.

● When mounting the camera on a wall, rotate the pan table by 180° to the left and

rotate the tilt table till the TOP mark above the lens always comes to the top side.

● When adjusting the viewing angle for camera mounted to ceilings, the enclosure and

installation auxiliary wire may be displayed on the screen depending on the direction

the camera is facing. Move the enclosure and installation auxiliary wire so that they

are not displayed on the screen. SFR311 SFR310

● Refer to “Using the CD-ROM” in the operating instructions on the provided

CD-ROM for further information about CDLauncher.

● When no image is displayed on the “Live” page, refer to the Troubleshooting in

the operating instructions on the provided CD-ROM.

● It is possible to enhance the network security by encrypting the access to camer-

as using the HTTPS function. Refer to the operating instructions on the provided

CD-ROM for how to configure the HTTPS settings.

● Click the [Setup] button on the “Live” page, the user authentication window will be

displayed. Enter the default user name and password as follows, and log in.

User name: admin

Password: 12345

● When changing settings related to the network settings, such as connection

mode, IP address, and subnet mask, click the [Network Settings] button in

[Panasonic IP Setting] screen as shown in step

e, then change each setting.

● Due to security enhancements in “IP Setting Software”, “Network settings” of the

camera to be configured cannot be changed when around 20 minutes have

passed after turning on the power of the camera. (When the effective period is set

to “20 min” in the “Easy IP Setup accommodate period”.)

However, settings can be changed after 20 minutes for cameras in the initial set

mode.

● “Network Camera Recorder with Viewer Software Lite” which supports live moni-

toring and recording images from multiple cameras is available. For further infor-

mation, refer to our website

(http://security.panasonic.com/pss/security/support/info.html).

● When cameras are displayed in [Panasonic IP Setting] screen, click the cam-

era with same MAC address as the MAC address printed on the camera that

you want to configure.

● Press the PUSH mark, release the four tabs of

the inner cover from the tilt table, and remove the

inner cover.

●

Securely tighten all the enclosure fixing screws (x2) of enclosure. Otherwise, the enclosure

dropping may result in injury. (Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})

● After complete installation, remove the cover film from the dome cover.

● Defocus may be caused by the reinstalled enclosure. In this case, perform the auto

focus function from the setup menu.

r If the installation screen of the viewer software “Network Camera View 4S” is displayed,

follow the instructions of the wizard to start the installation. (The viewer software is in-

stalled from the camera.)

● The License Agreement will be displayed. Read the Agreement and choose “I accept

the term in the license agreement”, and click [OK].

● The launcher window will be displayed. If the launcher window is not displayed, double

click the “CDLauncher.exe” le on the CD-ROM.

● The “Live” page will be displayed.

●

If you cannot install the viewer software “Network Camera View 4S” or if images are not

displayed, click the [Install] button next to [Viewer Software] on the launcher window to

install the software.

● Perform the [Time & date] settings in the “Setup” - “Basic” page before using the camera.

Congure the network

settings

 

Attachment plate ( : accessory)Ⓐ

Fixing screws for

attachment plate: p2-x4

(M4, locally procured)

●

Align the FRONT direction (the direction of FRONT marker on the camera that indicates the

installation direction when installing the camera) of template A (©: accessory) with the desired

direction, and drill through a 25.4 mm {1 inch} diameter hole.

●



If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inches} diameter

hole in the center. By doing so you can adjust the mounting direction of the camera in 90° increments.

MONITOR OUT conversion plug

( : accessory)Ⓕ

About the SD memory card

● To remove the SD memory card, hold down

the SD ON/OFF button (about 2 seconds).

When the ashing SD MOUNT indicator goes

out, you can remove the SD memory card.

● After the SD memory card has been replaced,

press the SD ON/OFF button (less than 1

second), and make sure the SD MOUNT

indicator is continually lit.

● If you do not press the SD ON/OFF button

after replacing the SD memory card, the

SD MOUNT indicator is automatically lit

approximately 5 minutes later.

46 mm {1-13/16 inches} 83.5 mm {3-9/32 inches}

Two-gang junction box

Attachment plate ( : accessory)Ⓐ

Fixing screws for attachment plate: x4 (M4, locally procured)

Azimuth adjustment ring Zoom knob

Loosen 2 enclosure xing screws of

the enclosure with the bit (Hex wrench,

screw size 6.35 mm {1/4 inches} T10)

(Ⓑ: accessory), and remove the enclo-

sure from the camera.

w Remove the power cord plug

( : accessory) and the external I/O Ⓓ

terminal plug ( : accessory) Ⓔ

attached to the camera.

e Connect cables to the camera according to

the instructions in “Making connections”, and

temporarily x the camera by inserting and

rotating attachment mounting screws into the

holes of the attachment plate ( : accessory).Ⓐ

● Be sure to tighten the camera fixing screw.

Failure to observe this may cause camera trouble

due to camera falling. (Recommended tightening

torque: 0.78 N·m {0.58 lbf·ft})

r Secure the camera by tightening the camera xing screw. mark on the camera lens head facing

the front (i.e. the direction of FRONT

mark on the camera).

y Press the PUSH mark on both sides of

the inner cover at the same time, and

remove the inner cover as shown in

the following illustration.

t Loosen the cross-head side of tilt table xing screw (on

one side), and incline the tilt table while keeping the TOP

● After cables have been connected to the camera, align the

OPEN mark of the camera side panel with the tab of the

attachment plate, insert 2 attachment mounting screws into the

attachment plate, and rotate the camera by approximately 15°.

The LOCK mark is moved to the tab position of the attachment

plate and the camera is temporarily secured.

* The fixing angle of the camera can be rotated in 90° increments.

Enclosure

Bit ( : accessory)Ⓑ

Enclosure fixing

screw (x2)

Cross-head side of

tilt table fixing screw

(opposite side of the

camera)

TOP mark

Press both sides

at the same time

Press

PUSH mark (x2)

Inner cover

Tilt table

Tab of the

inner cover

When installing the camera directly on the

ceiling or wall with cables exposed, or when

mounting the camera using the ceiling mount

bracket WV-Q174B (option), cut out a portion of

the dome cover to open a cable access hole.

●

● Disconnect either the 12 V DC power

source or PoE power source to prevent

power from being supplied during

mounting work.

● To prevent injuries and protect the

cables, finish the side cable access hole

with a file to avoid sharp edges.

Tab of the attach-

ment plate

Side cable access hole

q Turn on power for the camera by either connect-

ing an Ethernet cable or a 12 V DC power cable.

Connect the MONITOR OUT conversion plug

(

Ⓕ

: accessory) to the MONITOR OUT terminal of

the camera, and then connect the monitor for ad-

justment with a RCA pin cable (locally procured).

e Insert an SD memory card into the slot, if

necessary.

● Insert the SD memory card with its label

facing down.

● For information about performing the SD

memory card setting, refer to the operating

instructions (included in the CD-ROM).

●

r Loosen the pan table xing screw, and adjust

the angle of the camera with the tilt table, pan

table, and azimuth adjustment ring.

Horizontal (PAN) angle: +120° (Right) to

-240° (Left)

Vertical (TILT) angle: ±85°

Azimuth (YAW) angle: ±100°

t Tighten the cross-head side of tilt table xing

screw (on one side) and the pan table xing

screw, and x the camera.

(Recommended tightening torque:

0.59 N·m {0.44 lbf·ft})

y Adjust the zoom and focus.

1. Loosen the zoom knob equipped with

auxiliary handle (Ⓖ

accessory) by rotating

the knob to the left, and move it between

TELE and WIDE to obtain the appropriate

angle of view. Then, lock the zoom knob by

rotating it back to the right.

2. Adjust the focus by pressing the auto focus

(AF) button.

3. Adjust the screen size and focus by repeat-

ing steps 1 and 2. Readjust the angle of the

camera with the tilt table, pan table, and

azimuth adjustment ring if necessary.

u Press the PUSH mark on both sides of the

inner cover, and install the inner cover to the

place where it was removed.

i Disconnect the monitor for adjustment.

Attach the enclosure and secure it by tightening

the enclosure xing screws.

(Attach the enclosure by aligning the Panasonic

logo to the direction marker (FRONT ) on the

camera.)

PUSH mark (x2)

SD memory card (with

label facing down)

MONITOR OUT terminal

Enclosure

Auto focus (AF) button

TELE

WIDE

Vertical (TILT) angle

Tilting table

Horizontal (PAN)

angle

Azimuth (YAW)

angle

FRONT mark

Tab of the

inner cover

Pan table xing

screw (inside

this part)

Tilt table xing screw

Inner cover

Auxiliary handle ( : accessory)Ⓖ

Do not remove the auxiliary wire.

 The enclosure is fixed only with enclosure

fixing screws. Please be careful about the

handling when you wish to remove.

SFN311 SFN310

SFR311 SFR310

Produktspezifikationen

Marke:	Panasonic
Kategorie:	Sicherheitskamera
Modell:	WV-SFR311A
Schutzfunktion:	Vandalismussicher
Eingebautes Mikrofon:	Nein
Unterstützte Audioformate:	G.711
Gewicht:	700 g
Produktfarbe:	Weiß
Übertragungstechnik:	Kabelgebunden
Höhe:	102.5 mm
Energiequelle:	PoE
Befestigungstyp:	Zimmerdecke
Betriebstemperatur:	-10 - 50 °C
Netzstandard:	IEEE 802.3af
Unterstützte Sicherheitsalgorithmen:	SSL/TLS
Eingebauter Ethernet-Anschluss:	Ja
Sprachcodec:	G.711, G.726
Stromverbrauch (Standardbetrieb):	4.5 W
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Typ:	IP-Sicherheitskamera
Gehäusematerial:	Aluminium
Zahl der Benutzer:	14 Benutzer
Energieverbrauch:	370 mA
Unterstützt Windows-Betriebssysteme:	Ja
Unterstützte Sprachen:	CHI (SIMPL), CHI (TR), DEU, ENG, ESP, FRE, ITA, JPN, POR, RUS
Audio-System:	2-Wege
Analoges Signalformatsystem:	NTSC, PAL
Unterstützte Video-Modi:	720p
Unterstützte Grafik-Auflösungen:	1280 x 960
Unterstützte Videoformate:	H.264
Autofokus:	Ja
Digitaler Zoom:	4 x
Geräuschunterdrückung:	Ja
Schnittstelle:	RJ-45
Größe des Bildsensors:	1/3 Zoll
PTZ Kontrolle:	Ja
Formfaktor:	Kuppel
Durchmesser:	129.5 mm
Videokompressionsformate:	H.264
Maximale Auflösung:	1280 x 960 Pixel
Unterstützung von Positionierung:	Innen & Außen
DC-Ausgang Volt:	12
Brennweitenbereich:	2.8 - 10 mm
Bis zu 30 Frames pro Sekunde:	60 fps
Tag/ Nachtmodus:	Ja
Mindestbeleuchtung:	0.0007 Lux
Sensor-Typ:	MOS
Optischer Zoom:	3.6 x
Weißabgleich:	ATW, AWC
Bildqualitätsanpassung:	Helligkeit
Wide Dynamic Range (WDR):	Ja
Kamera Verschlusszeit:	1/10000 s
Vollbildverfahren:	Ja
Maximale Blendenzahl:	1.6
Datenschutz-Maskierung:	Ja
Video-Bewegungsmelder:	Ja
Infrarot (IR)-Abschaltfilter:	Ja
Abnehmbarer IR-Sperrfilter:	Ja