OSD Audio RS850 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr OSD Audio RS850 (5 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war fĂĽr 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
18 AWG minimum - for distances up to
………………………. . 10 ft
16-2AWG - from ……………………………………………. 10 to 50 ft
14-4AWG - from …………………………………………… 50 to 100ft
- Where is the best place to install the speakers?
- Where will the speakers sound the best?
- Try to separate the speakers 15 - 20 f
eet apart.
- Place the speakers in the location where they will
camouage the best with your surrounding
Q alla ouick inst ti n guide
- Trench Spade/Shovel
- Wire Cutter
- Measuring Tape
- Outdoor Volume Control (Optional)
- Direct Burial Cables
- Silicon Cable Connectors (Optional)
Tools needed for installation
To determine the length and the gauge of speaker wire, you will need to
measure the distance between your receiver/amplifier and the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
Speaker wire
Rock Speaker Owner’s Manual
Step 1
Select your location
Designate the general area where the rock speakers would be most
ideal. The speakers should face the general listening area and
spaced about15 – 20 feet apart for good stereo sound. (See
Diagram1) Furthermore, the realistic rock shape and finish would
blend particularly well in your landscape if it is placed near a rock
wall, water fountain, open plantation or swimming pool.
Avoid placing the speakers in low spots that would make the
speakers vulnerable to water accumulation.
Step 2
Trenching and Cable Burying
Measure the distance from the designated speaker location to your
stereo receiver. Try to minimize your distance without compromis-
ing on your overall appeal and safety concern. Once the route is
determined, use your spade or trench to dig the route with width
between 8”-12” once the trench route is completed, lay the cable in
the route. If using the PVC pipe, cut the pipe to length, ensure all
electrical connections are watertight with silicone burial connec-
tors. Once the cable layout is done, refill the trench. (See Diagram 2)
Step 3
Making the connection
Rock speakers are easily connected to any audio amplifier or stereo
receiver using the sealed speaker wire pigtail from the back of the
speaker enclosure. Please note, the red lead indicates positive signal
(+) and the black indicates negative signal (-). Connecting the positive
and negative leads incorrectly will cause it to be out of phase and will
result in weaker bass response.
Receiver/Amp
A U D I O
OSD
Center of Ref erence
FR
FL
RL RR
Diagram 1
Diagram 3
15’ - 20’
15’ - 20’
15’ - 20’
15’ - 20’
Remove 2”- 3” of the outer layer of the speaker wire coming out from the source amplifier. Carefully strip ½” of the insulation covering the
speaker conductors within the outer layer. Twist the bare speaker wire leads together and seal with burial connector. Do not use Eletrical tape
as a means of weatherproofing the wire connection. (See Diagram 3)
Diagram 3
Rock Speaker
Diagram 2
Burial Connectors
Speaker Cable
+-+-
12-2AWG - from …………………………………………… 50 to 100ft
Warranty & Repair
All OSD Audio speaker products have 1 year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims.
During the warranty period OSD will replace any defective part and correct any defect in workmanship without charge for either parts or labor.
OSD Audio may replace returned speakers with a product of equal value and performance. In such cases, some modications to the mounting may be necessary and
are not OSD’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD. The unit must be
returned to OSD at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damaged
resulting from abuse or from servicing performed by an agency or person not specically authorized in writing by OSD.
OSD Audio sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD product purchased
from an unauthorized dealer or other source, including retailers, mail over dealers and online sellers will not be honored or serviced under existing OSD warranty
policy. Any sale of product by an unauthorized source or other manner not authorized by OSD shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail
value of the parts and labor. To return for repairs, you must email customer service at RMA@osdaudio.com for a Returned Merchandise Authorization (RMA) number# then the
unit must be shipped to OSD at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container with
at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover:
Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) Any products that have been altered or modied Any product whose • •
identifying number of decal, serial #, etc. has been altered, defaced or removed Normal wear and maintenance.•
Diagram 5
Not all receivers/amplifiers can safely operate 2 pair of speakers at the
same time. It is important that the amplifier or receiver’s output wattage
is comparable to the speaker’s power handling. Please refer to your
owner’s manual for reference.
When connecting any speakers to the amplifier or receiver, always make
sure the power is off. Locate the connection terminals on the back of
your receiver or amplifier. Always make sure to connect audio out from
the back of your receiver or amplifier to the speakers.
Step 5
Connect the speaker cable to the speaker cable terminals, matching
the proper polarity with your amplier, + to + (red) and - to - (black).
Make sure to connect the right channel to the right speaker and the
left channel to the left speaker . Either channel may be attached to
either terminals set, however, be sure that polarity ( + and - ) is correct
on each channel or the performance of the speaker will be seriously
aected as one channel will cancel out the other.
OSD
Audio
OSD
Audio
LR
SURR BACK SPEAKERS
SURR SPEAKERS
FRONT SPEAKERS RIGHT FRONT SPEAKERS LEFT
CENTER
L R LRLR
LEFT SPEAKER
RIGHT SPEAKER
Receiver/Amplifier
OSD Audio • 775 columbia st • ea • A • 92821 • • Tel (888) 779-4968 • Br C www.osdaudio.com Fax (714) 256-8300


Produktspezifikationen

Marke: OSD Audio
Kategorie: Lautsprecher
Modell: RS850

Brauchst du Hilfe?

Wenn Sie Hilfe mit OSD Audio RS850 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher OSD Audio

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung fĂĽr -Kategorien-