OSD Audio ACE520 Bedienungsanleitung

OSD Audio Lautsprecher ACE520

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für OSD Audio ACE520 (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
18AWG minimum - for distances up to ………………………. . 10 ft
16AWG - from ……………………………………………. 10 to 50 ft
14AWG - from …………………………………………… 50 to 100ft
- Where is the best place to install the speakers
- Where do the speakers sound the best?
- Try to separate the speakers 6 - 10 feet apart.
- If you intend to paint the grilles, try to do so before installation.
Q k installation uic guide
- Pencil
- Drill
- Tape Measure
- Wire cutter
- Philips-head screwdriver
- Sandpaper
Tools needed for installation
STEP 4: Mounting Dog Ear
Tighten the dog-ear brackets by simply turning the screws on the
slowly clockwise. The quick-turn mounting system and frame will
"sandwich" or clamp around the wall to hold the speaker securely in
place. (See Diagram 4)
STEP 1: Cutout Tracing
Trace along the inclusive template. Cut along the traced line using a
drywall saw or rotary drill. A simple, inexpensive drywall saw (about
$10 at your local hardware store) is the best choice for beginners.
Caution: This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the
desired mounting area, you should start by cutting a small hole in
the center of your penciled mounting hole with a drywall saw. Use a
piece of sandpaper to sand down the cut out edge for a smoother
contour. (See Diagram 1 )
Run the cable into the cut out location while leaving an extra two
feet to make the connection to the speaker easier. Strip back
approximately ½ inch of the speaker cable insulation and twist
the copper wires tightly for easy insertion.
On the back of the speaker, press down on the gold-plated
compression terminal to reveal the "eye" and insert the speaker
cable through the eye for secure connection. Release the compres-
sion terminal to lock each cable securely. ( See Diagram 2)
STEP 3: Tweeter Adjustment
To determine the length and the gauge of speaker wire, you will need to
measure the distance between your receiver/amplifier to the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
- Utility knife
- Safety eyewear
- Gloves
Speaker wire
I ng Speakersn-Ceili
Owner’s Manual
Architectural Invisible
A I OU D
OSD
- When placing the speakers in the ceiling, try to install them
listening area. (For LCR model only)
Your in-ceiling speakers come from the factory with the tweeter facing
response. However, you can adjust the tweeter to focus e sound at th
your listening location. In order to do this, gently press on the grill (See
Diagram 3). Caution: Do not touch the tweeter dome while adjusting for
your hearing preference. (See Diagram 3) -Pivoting Tweeter Model Only.
Diagram 3:
Adjust the tweeter here
Tweeter
STEP 2: Cut Out
Diagram 1:
Diagram 2:
Dog Ear
Diagram 4:
Mounting Dog Ear
Lock
LOSE
wattage is comparable to the speaker’s power handling. Please refer to
your owner’s manual for reference.
Note: The wire for both speakers should be about the same length.
the excess wire behind the wall
TIP: Blow in- n nsi ulation can sometimes wor ik ts way into e m vingth o
c pom onent os f he speaket r, negatively impa ting pec rform cean . t isI
be t s to epr lace about a one square fo c rec he ot se tion di tly behind t
s kpea er wi h t rol ed-il n (ba ns ati t) i ul on. (Se De iagram 6)
Note: Speaker terminals have corresponding (+) and (-) terminals. It is
important to connect both speakers in phase. Out of phase will result in
thin sound and weak bass.
BASS
TREBLE
+3 0 -3 +3 0 -3
+_+_
Bass Adjustment Switch
Treble Adjustment Switch
-+Receiver/Amplifier
LEFT OUT
- +
RIGHT OUT
RIGHT
LEFT
Power handling
(10 watts)
minimum
Diagram 5 Adjustment Switches
Diagram 7
Warranty & Repair
All OSD AUDIO speaker products have (10) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims.
During the warranty period OSD AUDIO will replace any defective part and correct any defect in orkmanship without charge for either parts or laborw
OSD AUDIO may replace returned speakers with a product of equal value and performance. In such cases, some modications to the mounting may be necessary and
are not OSD AUDIO’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD AUDIO. The unit
must be returned to OSD AUDIO at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor
is damaged resulting from abuse or from servicing performed by an agency or person not specically authorized in writing by OSD Audio
OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD AUDIO product
purchased from an unauthorized dealer or other source, including retailers, mail over dealers and online sellers will not be honored or serviced under existing OSD
AUDIO warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD AUDIO shall void the warranty on the applicable
product.
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail
value of the parts and labor. To return for repairs, you must email customer service at RMA@OSDAUDIO.com for a Returned Merchandise Authorization (RMA) number# then
the unit must be shipped to OSD AUDIO at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated
container with at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover:
Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) Any products that have been altered or modied Any product whose • •
identifying number of decal, serial #, etc. has been altered, defaced or removed Normal wear and maintenance.•
STEP 5
TIP: Adjust the bass and the treble setting on your speakers by
shifting the knob either to the left or rig . Speakers positioned ht
with the tweeter switch in the +3dB position. Speakers located
within a few feet of a listener's ear will often sound better with the
tweeter switch set to -3dB. Furthermore, rolled in insulation materi-
als, such as a foam bedding would work as a dampening material
(See Diagram 5)
(Not applicable to certain models)
When connecting any speakers to the amplier or receiver, always make
sure the power is o. Locate the connection terminals on the back of
your receiver or amplier. Always make sure to connect audio out from
the back of your receiver or amplier to the speakers. (See Diagram 7)
closer to a corner often produce more bass and will usually benefit
+_
- + - +
Amplifier/Receiver Considerations.
Architectural
Ceiling Element
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:
Power Handling:
Dimensions:(D x H)
Contour Switches:
Ceiling Cut Out:
Unit of Measure:
ACE-850MK
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8 
92dB
25Hz - 22kHz
200 Watts
9 ½”
Pair
10 ¾” x 5”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
8” Kevlar In Ceiling
Home Theater Speakers
ACE-800
1” Pivoting Silk Dome
8” Polypropylene
8 
90dB
45Hz - 22kHz
120 Watts
9 ⁄”
Pair
10 ¾” x 3 ⁄”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
8” Custome Series
Ceiling Speakers
ACE-540
¾” Pivoting Silk Dome
5 ¼” Polypropylene
8 
91dB
65Hz - 20kHz
120 Watts
6 ⁄”
Pair
7 ⁄” x 3 ½”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
5 ¼” Custome Series
Ceiling Speakers
ACE-520
¾” Pivoting Silk Dome
8 
91dB
75Hz - 22kHz
100 Watts
6 ⁄”
Pair
7 ⁄” x 3 ½”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
5 ¼” Custome Series
Ceiling Speakers
Pair
6 ½” Polypropylene
8 
92dB 1W/1m
36Hz - 22kHz
150 Watts
ACE-645
6 ½” High Denition
Pro Series Ceiling Speakers
8 ⁄” x 4 ¼”
7 ⁄”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
1 Pivoting ” Silk High
Teteron Dome
ACE-640
6 ½” Polypropy nele
8 
91dB
38Hz - 22kHz
150 watts
Pair
1” Pivoting Silk Dome
ACE-600
¾” Pivoting Silk Dome
6 ½” Polypr yleneop
8 
89dB
58Hz - 22kHz
125 Watts
7 ⁄”
Pair
8 ⁄” x 4”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
ACE-750
1” Pivoting Aluminum
Tweeter
7” lar onesKev C
8 
91dB 1W/1m
28Hz - 22kHz
200 Watts
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
Pair
9” x 3 ⁄”
8”
8 ⁄” x 4 “
7” Kevlar In Ceiling
Home Theater Speakers
6 ½” High Denition
Pro Series Ceiling Speakers
6 ½” Custome Series
Ceiling Speakers
Pair
3” Polypropylene
8 
88dB 1W/1m
120Hz - 20kHz
60 Watts
ACE-400
3” Architectural Ceiling
Speakers
4 ⁄” x 2 ½”
4 ½”
N/A
N/A
N/A
5 ¼” Polypropylene
ACE-550MK
1” Pivoting Aluminum
Tweeter
5 ¼” Kevlar Cones
8 
91dB
50Hz - 22kHz
150 Watts
6 ⁄”
Pair
7 ⁄” x 3 ½”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
5 ¼” Kevlar In Ceiling
Home Theater Speakers
ACE-950
1” Pivoting Aluminum
Tweeter
8 ½” Kevlar Cones
8 
91dB
25Hz - 22kHz
225 Watts
8 ⁄”
Pair
10 ¾” x 5”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
8 ½” Kevlar In Ceiling
Home Theater Speakers
ACE-650MK
1” Pivoting Aluminum
Tweeter
6 ½” lar onesKev C
8 
92dB 1W/1m
28Hz - 22kHz
175 Watts
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
Pair
8 ⁄” x 4 ¼”
7 ⁄”
6 ½” Kevlar In Ceiling
Home Theater Speakers
Pair
5 ¼” Polypropylene
8 
89dB 1W/1m
79Hz - 20kHz
75 Watts
ACE-500
5 ¼” Architectural
Ceiling Speakers
7 ⁄” x 3 ½”
7”
N/A
N/A
¾” Pivoting Silk Dome
ACE-590
¾” Pivoting Silk Dome
6 ½” Polypr yleneop
8 
89dB
62Hz - 20kHz
100 Watts
8.15”
Pair
8 ⁄” x 4”
2-Position Fro -Mounted nt
±3dB Bass & Treble Switches
6 ½” Custome Series
Ceiling Speakers

Produktspezifikationen

Marke: OSD Audio
Kategorie: Lautsprecher
Modell: ACE520

Brauchst du Hilfe?

Wenn Sie Hilfe mit OSD Audio ACE520 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher OSD Audio

OSD Audio

OSD Audio ACE840TT Bedienungsanleitung

24 September 2024
OSD Audio

OSD Audio SVC-100 Bedienungsanleitung

24 September 2024
OSD Audio

OSD Audio ICE630ST Bedienungsanleitung

19 September 2024
OSD Audio

OSD Audio LS2 Bedienungsanleitung

19 September 2024
OSD Audio

OSD Audio Black R63A Bedienungsanleitung

5 September 2024
OSD Audio

OSD Audio Black R83 Bedienungsanleitung

5 September 2024
OSD Audio

OSD Audio Black R63 Bedienungsanleitung

5 September 2024
OSD Audio

OSD Audio Black R61 Bedienungsanleitung

5 September 2024
OSD Audio

OSD Audio Black R81 Bedienungsanleitung

5 September 2024
OSD Audio

OSD Audio Black R83A Bedienungsanleitung

5 September 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024