Oregon Scientific WMR 112 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Oregon Scientific WMR 112 (77 Seiten) in der Kategorie Wetterstation. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/77
1
EN
CABLE FREE WEATHER
STATION
MODEL: WMR112 / WMR112U (UK VERSION)
USER’S MANUAL
SECTION 1 INTRODUCTION
Congratulations on your purchasing the WMR112/112U Cable Free
Weather Station. An all-purpose easy-to-use system, the WMR112/
112U lets you monitor the following weather elements:
-Air temperature
-Relative humidity
-Barometric pressure
-Wind speed and direction
-Rainfall
The WMR112/112U is also equipped with:
-RF calendar clock with daily alarm
-Weather forecast within 32 to 48 km (20- to 30-mile) radius
-Weather alarms
-Memory for maximum and minimum readings
-Touch-screen plus key button operation
STANDARD PACKAGE
The original WMR112/112U comes complete with the following:
-Main unit (WMR112/112U)
-Anemometer (WGR918N)
-Thermo-hygrometer (THGN228NX)
-Rain gauge (PCR918N)
-Baro-thermo-hygrometer (BTHR918N)
-12V AC adapter
The rain gauge is powered by solar transmitter STR928N while the
anemometer is powered by solar transmitter STR938.
The WMR112/112U can support up to seven different remote
instruments. You can connect up to three optional thermo or thermo-
hygro sensors to the system.
Optional items include:
-Thermo-hygro sensor (THGR228N/THGR238N)
-Thermo sensor (THR228N/THR238N)
Contact an authorized dealer for optional items.
SECTION 2 INSTALLATION
The WMR112/112U operates at 433MHz. No wire installation is
required among units.
The WMR112/112U has an effective range of 100 meters in an open
area. Position the units within the range and be sure the transmission
path is clear of interference and obstacles.
Note: The anemometer, thermo-hygrometer and rain gauge should
be installed outdoors and in locations that best measure the weather
elements which the instruments are designed for. As for the baro-
thermo-hygrometer, it must be installed indoors. If you have any
optional thermo or thermo-hygro sensors, they can be installed
outdoors or indoors.
THE ANEMOMETER
The anemometer measures wind speed and direction.
To install it,
1. Unscrew the solar transmitter STR938.
2. Plug in the connector of WGR918N into the solar transmitter as
shown.
3. Secure the screws again.
2
EN
4. Place the wind cup over the thinnest shaft on the anemometer’s
T-bar.
5. Tighten the screw on the base of the wind cup.
6. Align the red markings on the wind vane’s shaft.
7. With the aid of a compass, face the red marking south before
mounting the anemometer.
8. Mount the anemometer and its solar transmitter safely in place.
The wind speed and direction window on the main unit should read
180 if the main unit is installed.°
9. Press [RESET] of STR938 after installation.
THE THERMO-HYGROMETER
The thermo-hygrometer measures outdoor temperature and humidity.
It uses two (2) UM-4 or “AAA” size batteries.
Follow these steps to install / replace batteries:
1. Remove the screws on the battery compartment.
2. Insert the batteries strictly according to the polarities shown
therein.
3. Replace the battery compartment door and secure its screws.
4. Press the [RESET] button.
THE RAIN GAUGE
The rain gauge measures the total amount and rate of rainfall.
To install it:
1. Unscrew the solar transmitter STR928N.
2. Plug in the connector of PCR918N into the solar transmitter as
shown.
3. Secure the screws again.
4. Open the cover of the rain collector.
5. Remove the fiber tape from around the bucket assemblies.
6. Mount the rain gauge and its solar transmitter safely in place.
7. Put drops of water on the cross at the base on the rain collector
to check the leveling.
8. Use metal ring to adjust the leveling of the rain collector if
necessary.
9. Close the cover of the rain collector.
10. Press [RESET] of STR928N after installation.
THE SOLAR TRANSMITTERS
The solar transmitters make use of solar energy to power the
instruments they are connected to. Two pieces of UM3 or "AA" -
sized batteries are needed as back-up power.
Note: It is recommended to insert two UM3 or “AA”-sized super
lithium batteries for weather condition under 0 °C.
For the solar transmitters to function properly, make sure the solar
receptors on the transmitters are exposed to sunlight and the
connectors of the connection cable are securely plugged in.
Water stay at
position 1 - 4
means the gauge
is not leveled
METAL RING
3
EN
THE BARO-THERMO-HYGROMETER
The baro-thermo-hygrometer measures the atmospheric pressure,
temperature and humidity.
The sensor uses four UM4 or “AAA”-sized batteries.
To install it,
1. Insert alkaline batteries accordingly.
2. Mount the unit where you want to monitor the readings. Or you
can make use of its table stand to place it on a flat surface.
THE MAIN UNIT
The main unit gives you all the readings and controls. It should be
placed indoors.
The main unit is powered up by the 12V AC adapter.
To install it,
1. Position the main unit and other units within effective range
(100 meters).
2. Insert four UM4 or “AAA”-sized alkaline batteries for backup
purpose.
3. Mount the main unit safely in place. Or use its docking bracket
to place it on a flat surface.
4. Connect the AC power adapter to the main unit and a wall socket.
5. Press the [RESET] button on the main unit to initiate operation.
The main unit will start searching for signals for about four minutes.
Upon successful reception, the readings will be displayed. The main
unit will update the readings at regular intervals.
TABLE-STAND
A docking bracket is provided so that you can rest the unit into it as
well as for placement of the Stylus provided. The Stylus is designed
to facilitate the touch-screen operation but you can also operate this
function simply by touching the screen with your finger.
Caution: Do not press the screen too hard with the Stylus or it would
cause damage to the display.
LOW-BATTERY WARNING
There are low-battery indicators [ ] for the main unit, rain gauge,
baro-thermo-hygrometer, thermo-hygrometer and optional remote
thermo and thermo-hygro sensors. Replace the batteries when the
respective indicators light up.
Note: The readings collected from the thermo-hygrometer and any
optional remote thermo and thermo-hygro sensors share the same
display window. The “OUTand remote channel will share the
same low-battery indicator. When the battery level of the thermo-
hygrometer is low, the low-battery indicator will turn on. If it is one
of the optional remote sensors, the low-battery indicator will blink.
To locate the channel in question, press the window to scan through
all available devices. The low-battery indicator will stop blinking if
the battery level is low for that one.
DC 12V
Stylus
Docking bracket


Produktspezifikationen

Marke: Oregon Scientific
Kategorie: Wetterstation
Modell: WMR 112

Brauchst du Hilfe?

Wenn Sie Hilfe mit Oregon Scientific WMR 112 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Wetterstation Oregon Scientific

Bedienungsanleitung Wetterstation

Neueste Bedienungsanleitung für -Kategorien-