Omron BP742N Bedienungsanleitung

Omron Blutdruckmessgerät BP742N

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Omron BP742N (2 Seiten) in der Kategorie Blutdruckmessgerät. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Introduction

Thank you for purchasing the OMRON® BP742N Blood Pressure Monitor.

Your new blood pressure monitor uses the oscillometric method of blood pressure

measurement. This means the monitor detects your blood movement through your

brachial artery and converts the movements into a digital reading. An oscillometric

monitor does not need a stethoscope so the monitor is simple to use.

Intended Use

This device is a digital monitor intended for use in measuring blood pressure and

pulse rate in adult patient population who can understand this instruction manual

with the arm circumference range printed on the arm cuff. The device detects the

appearance of irregular heartbeats during measurement and gives a warning signal

with the measurement result.

Please read this instruction manual thoroughly before using the device.

Please keep for future reference. For specific information about your own blood

pressure, CONSULT YOUR PHYSICIAN.

Important Safety Information

Warning: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

(General Usage)

DO NOT adjust medication based on measurement results from this blood

pressure monitor. Take medication as prescribed by your physician. Only a

physician is qualified to diagnose and treat High Blood Pressure.

This device is not intended to be a diagnostic device.

Consult your physician before using the device in pregnancy including

pre-eclampsia, or if diagnosed with arrhythmia or arteriosclerosis.

Do not use the device on the injured arm or the arm under medical treatment.

Do not apply the arm cuff on the arm while being on an intravenous drip or blood

transfusion.

Consult your physician before using the device on the arm with an arterio-venous

(A-V) shunt.

Do not use the device with other medical electrical (ME) equipment

simultaneously.

Do not use the device in the area the HF surgical equipment, MRI, or CT scanner

exists, or in the oxygen rich environment.

The air tube or the AC adapter cable may cause accidental strangulation in

infants.

Contained small parts that may cause a choking hazard if swallowed by infants.

(AC Adapter (optional) Usage)

Do not use the AC adapter if the device or the power cord is damaged. Turn off

the power and unplug the power cord immediately.

Plug the AC adapter into the appropriate voltage outlet. Do not use in a

multi-outlet plug.

Never plug in or unplug the power cord from the electric outlet with wet hands.

Caution: Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury to the user or patient or

damage to the equipment or other property.

(General Usage)

Always consult your physician. Self-diagnosis of measurement results and

self-treatment are dangerous.

People with severe blood flow problems, or blood disorders, should consult a

physician before using the device, as the arm cuff inflation can cause bruising.

Remove the arm cuff if it does not start deflating during the measurement.

Do not use this device on infants or persons who cannot express their intentions.

Do not use the device for any purpose other than measuring blood pressure.

Use only the approved arm cuff for this device. Use of other arm cuffs may result

in incorrect measurement results.

Do not use a mobile phone or other devices that emit electromagnetic fields,

near the device. This may result in incorrect operation of the device.

Do not disassemble the monitor or arm cuff. This may cause an inaccurate

reading.

Do not use in a location with moisture, or a location where water may splash on

the device. This may damage the device.

Do not use the device in a moving vehicle (car, airplane).

Do not take measurements more than necessary. It may cause bruising due to

blood flow interference.

Consult your physician before using the device if you had a mastectomy.

Read "If your systolic pressure is more than 210 mmHg" of this instruction

manual, if your systolic pressure is known to be more than 210 mmHg. Inflating

to a higher pressure than necessary may result in bruising where the arm cuff is

applied.

(AC Adapter (optional) Usage)

Fully insert the power plug into the outlet.

When disconnecting the power plug from the outlet, do not pull the power cord.

Be sure to pull from the power plug safely.

When handling the power cord, take care not to do the following:

Wipe the dust off from the power plug.

Unplug monitor when not in use.

Disconnect the power plug before cleaning.

Use only an OMRON AC adapter designed for this device. Use of unsupported

adapters may damage and/or may be hazardous to the device.

(Battery Usage)

Do not insert the batteries with their polarities incorrectly aligned.

Use only 4 “AA” alkaline or manganese batteries with this device. Do not use

other types of batteries. Do not use new and used batteries together.

Remove the batteries if the device will not be used for three months or more.

General Precautions

• Do not forcibly crease the arm cuff or the air tube excessively.

• Do not press the air tube while taking a measurement.

• To unplug the air plug, pull on the air plug at the connection with the monitor, not

the tube itself.

• Do not drop the monitor or subject device to strong shocks or vibrations.

• Do not inflate the arm cuff when it is not wrapped around your arm.

• Do not use the device outside the specified environment. It may cause an

inaccurate reading.

• Dispose of the device, components and optional accessories according to

applicable local regulations. Unlawful disposal may cause environmental pollution.

1. Know Your Device

Contents:

Monitor, arm cuff, battery set, instruction manual, quick start guide

Monitor:

Arm cuff:

Display:

1.1 Display symbols

Irregular Heartbeat Symbol ( )

When the monitor detects an irregular

rhythm two or more times during the

measurement, the irregular heartbeat

symbol ( ) will appear on the display

with the measurement values.

An irregular heartbeat rhythm is defined

as a rhythm that is 25% less or 25%

more than the average rhythm detected

while the monitor is measuring the systolic and diastolic blood pressure.

If the irregular heartbeat symbol ( ) displays with your measurement results,

we recommend you consult your physician. Follow the directions of your

physician.

Movement Error Symbol ( )

The movement error symbol is displayed if you move your body during the

measurement. Please remove the arm cuff, and wait 2 - 3 minutes.

Take another measurement, remain still during measurement.

Average Value Symbol ( )

The average value symbol is displayed when you press and hold the memory

button for more than 3 seconds. The most recent average value appears on

the display screen.

Blood Pressure Level Indicator

2013 ESH/ESC Guidelines for the management of arterial hypertension

Definitions of hypertension by office and home blood pressure levels

These are from statistical values for blood pressure.

1.2 Before Taking a Measurement

To help ensure an accurate reading, follow these directions:

1. Avoid bathing, drinking alcohol or caffeine, smoking, exercising and eating

for 30 minutes before taking a measurement. Rest for at least 15 minutes

before taking the measurement.

2. Stress raises blood pressure. Avoid taking measurements during stressful

times.

3. Measurements should be taken in a quiet place.

4. Remove tight-fitting clothing from your arm.

5. Sit on a chair with your feet flat on the floor. Rest your arm on a table so

that the arm cuff is at the same level as your heart.

6. Remain still and do not talk during the measurement.

7. Keep a record of your blood pressure and pulse readings for your

physician. A single measurement does not provide an accurate indication of

your true blood pressure. You need to take and record several readings

over a period of time. Try to measure your blood pressure at the same time

each day for consistency.

2. Preparation

2.1 Battery Installation

1. Remove the battery cover.

2. Insert 4 “AA” batteries as

indicated in the battery

compartment.

3. Replace the battery cover.

Notes:

• When the low battery symbol ( ) appears on the display, turn the monitor

off, then replace all batteries at the same time. Long life alkaline batteries

are recommended.

• The measurement values continue to be stored in memory even after the

batteries are replaced.

• The supplied batteries may have a shorter life.

Dispose of the device, components and optional accessories according to

applicable local regulations. Unlawful disposal may cause environmental

pollution.

2.2 Setting the Date and Time

Set the monitor to the correct date and time before taking a measurement for

the first time.

1. Press the button.

2. Push or to change the year.

Push button to confirm the year and then the month flashes. Repeat the

same steps to change the month, day, hour, and minute.

3. Press the START/STOP button to turn the monitor off.

Notes:

• If the batteries have been replaced, the date and time setting will need to be

reset.

• If the date and time are not set, “-:--” appears during or after measurement.

3. Using the Device

3.1 Applying the Arm Cuff

Remove tight-fitting clothing or tight rolled up sleeve from your left upper arm.

Do not place the arm cuff over thick clothes.

1. Insert the air plug into the air jack

securely.

2. Wrap the arm cuff firmly in

place around your left upper

arm.

The bottom edge of the arm cuff

should be 1/2 inch (1 to 2 cm) above

the elbow. Air tube is on the inside of

your arm and aligned with your middle

finger.

3. Secure closed with the

fabric fastener.

Notes:

• When you take a measurement on the right

arm, the air tube will be at the side of your

elbow. Be careful not to rest your arm on the

air tube.

• The blood pressure can differ between the right arm and the left arm, and

the measured blood pressure values can be different. OMRON recommends

to always use the same arm for measurement. If the values between both

arms differ substantially, please check with your physician which arm to use

for your measurements.

3.2 How to Sit Correctly

To take a measurement, you need to be

relaxed and comfortably seated, under

comfortable room temperature. Avoid

bathing, drinking alcohol or caffeine,

smoking, exercising or eating 30 minutes

before taking a measurement.

• Sit on a chair with your feet flat on the floor.

• Sit upright with your back straight.

• Sit with your back and arm being supported.

• The arm cuff should be placed on your arm at

the same level as your heart.

3.3 Taking a Measurement

Notes:

• To stop a measurement, press the START/STOP button once to deflate the

arm cuff.

• Remain still while taking a measurement.

The monitor is designed to take measurements and store the measurement

values in the memory for 2 people using USER ID 1 and USER ID 2.

1. Select your User ID (1 or 2).

2. Press the START/STOP button.

The arm cuff will start to inflate automatically.

3. Remove the arm cuff.

Press the START/STOP button to turn the monitor off.

The monitor automatically stores the measurement result in its memory.

It will automatically turn off after 2 minutes.

Note: Wait 2-3 minutes before taking another measurement. Waiting between

measurements allows the arteries to return to the condition prior to

taking a measurement.

Using the Guest Mode

The monitor stores measurement values for 2 users in the memory.

The guest mode can be used to take a single measurement for another user.

No measurement values are stored in the memory when the guest mode is

selected.

1. Press and hold the START/STOP

button for more than 3 seconds.

The USER ID symbol and the Date/Time

display will disappear.

2. Release the START/STOP button when the Date/Time display

turns off.

The arm cuff will start to inflate automatically.

DO NOT adjust medication based on measurement results from this blood

pressure monitor. Take medication as prescribed by your physician. Only a

physician is qualified to diagnose and treat High Blood Pressure.

This device is not intended to be a diagnostic device.

Always consult your physician. Self-diagnosis of measurement results and

self-treatment are dangerous.

Inflating to a higher pressure than necessary may result in bruising where the

arm cuff is applied.

3.4 Using the Memory Function

The monitor automatically stores the results up to 50 sets for each user (1 and

2). It can also calculate an average value based on the last 3 measurement

values taken within 10 minutes.

Notes:

• If there are only 2 measurement values in the memory for that period, the

average will be based on these 2 values.

• If there is 1 measurement value in the memory for that period, this is

displayed as the average.

• If the memory is full, the monitor will delete the oldest value.

• When viewing the measurement value taken without setting the date and

time, “-:--” is displayed instead of the date and time.

To View the Measurement Values Stored in Memory

1. Select your User ID (1 or 2).

2. Press the button.

The Memory number appears for a second

before the pulse rate is displayed.

The newest set is numbered “1”.

3. Press the or button to view the values stored in memory.

: To view the older values

: To view the more recent values

To View the Average Value

1. Select your User ID (1 or 2).

2. Press and hold the button for

more than 3 seconds.

Notes:

• If the previous measurement was taken without setting the date and time,

the average value is not calculated.

• If there are no measurements results stored in the memory,

the screen to the right is displayed.

To Delete All the Values Stored in Memory

The values stored in the memory are deleted by USER ID.

1. Select your User ID (1 or 2).

2. Press the button, while the memory symbol appears.

3. While holding the button

down, press the

START/STOP button for

more than 3 seconds.

Note: You cannot partially delete the values stored in the memory.

All values for the user you select will be deleted.

Do not damage. Do not break it.

Do not tamper with it. Do not forcibly bend or pull.

Do not twist. Do not bundle during use.

Do not pinch. Do not place under heavy objects.

2298802-0B

5 series

Blood Pressure Monitor

Model BP742N

Instruction Manual

A. Display

B. Up/Down buttons

C. USER ID selection switch

D. Date/Time setting button

E. START/STOP button

F. Memory button

G. Battery compartment

H. Air jack

I. AC adapter jack

(for optional AC adapter)

M. USER ID symbol

N. Systolic blood pressure

O. Diastolic blood pressure

P. Low battery symbol

Q. Heartbeat symbol

(Flashes during measurement.)

R. Memory symbol

S. Average value symbol

T. Date/Time display

U. Movement error symbol

V. Irregular heartbeat symbol

W. Blood pressure level indicator

X. Deflation symbol

Y. Pulse display / Memory number

Office Home

Systolic Blood Pressure ≥ 140 mmHg 135 mmHg≥

Diastolic Blood Pressure ≥ 90 mmHg ≥ 85 mmHg

J. Arm cuff

(Arm circumference 9” - 17” (22 - 42 cm))

K. Air plug

L. Air tube

Irregular Heartbeat

Normal Heartbeat

Pulse

Blood pressure

Short Long

Pulse

Minute

Change Confirm

Year

Month

Day

Hour

: Forward

: Back

1/2 inch

(1 - 2 cm)

START INFLATE DEFLATE COMPLETE

If your systolic pressure is more than 210 mmHg

After the arm cuff starts to inflate, press and hold the START/STOP

button until the monitor inflates 30 to 40 mmHg higher than your

expected systolic pressure.

Notes:

• The monitor will not inflate above 299 mmHg.

• Do not apply more pressure than necessary.

Alternating date/time

display

4. Error Messages and Troubleshooting

4.1 Error Messages

4.2 Troubleshooting

5. Maintenance and Storage

5.1 Maintenance

To protect your device from damage, please observe the following:

• Store the device and the components in a clean, safe

location.

• Do not use any abrasive or volatile cleaners.

• Do not wash the device and any components or immerse

them in water.

• Do not use gasoline, thinners or similar solvents to clean the

device.

• Use a soft and dry cloth, or a soft and moistened cloth and

neutral soap to clean on the monitor and the arm cuff.

• Changes or modification not approved by the manufacturer

will void the user warranty. Do not disassemble or attempt to

repair the device or components. Consult Customer Service.

5.2 Storage

1. Unplug the air plug from the air jack.

2. Gently fold the air tube into the arm cuff.

Note: Do not bend or crease the air tube

excessively.

Do not store the device in the following situations:

•If the device is wet.

•Locations exposed to extreme temperatures, humidity, direct sunlight, dust or

corrosive vapors such as bleach.

•Locations exposed to vibrations, shocks or where it will be at an angle.

5.3 Optional Medical Accessories

Using the Optional AC Adapter

1. Insert the AC adapter plug

into the AC adapter jack on

the rear side of the monitor.

2. Plug the AC adapter into an

electrical outlet.

To disconnect the AC adapter, unplug the AC adapter from the electrical outlet

first, and then remove the AC adapter plug from the monitor.

6. Specifications

Notes:

• These specifications are subject to change without notice.

• In the clinical validation study, the 5th phase was used on 85 subjects for

determination of diastolic blood pressure.

• This device has not been validated for use on pregnant patients.

7. FCC Statement

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

8. Limited Warranty

Your BP742N Automatic Blood Pressure Monitor, excluding the arm cuff and

batteries, is warranted to be free from defects in materials and workmanship

appearing within 2 years from the date of purchase, when used in accordance with

the instructions provided with the monitor. The arm cuff is warranted to be free from

defects in materials and workmanship appearing within 1 year from the date of

purchase when the monitor is used in accordance with the instructions provided

with the monitor. The above warranty extends only to the original retail purchaser.

We will, at our option, replace without charge any monitor or arm cuff covered by the

above warranty. Replacement is our only responsibility and your only remedy under

the above warranty.

To obtain warranty service contact Customer Service by calling 1-800-634-4350 for

the address of the inspection center and the return shipping and handling fee.

Enclose the original printed receipt. Include a letter, with your name, address, phone

number, and description of the specific problem. Pack the product carefully to

prevent damage in transit. Because of possible loss in transit, we recommend

insuring the product with return receipt requested.

THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY OMRON IN

CONNECTION WITH THIS PRODUCT, AND OMRON HEREBY DISCLAIMS ANY

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. IMPLIED WARRANTIES AND OTHER TERMS THAT MAY BE

IMPOSED BY LAW, IF ANY, ARE LIMITED IN DURATION TO THE PERIOD OF

THE ABOVE EXPRESS WARRANTY.

OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER SPECIAL,

INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, EXPENSES OR

DAMAGES.

This warranty provides you with specific legal rights, and you may have other rights

that vary by jurisdiction. Because of special local requirements, some of the above

limitations and exclusions may not apply to you.

9. Guidance and Manufacturer’s Declaration

OMRON Automatic Blood Pressure Monitor

Information for accompanying documents in the scope of IEC60601-1-2:2007

Model: BP742N including AC-adapter

Error Display Cause Solution

Irregular heartbeats are

detected.

Remove the arm cuff. Wait 2 - 3

minutes and then take another

measurement. Repeat the steps

in section 3.3. If this error

continues to appear, contact

your physician.

Movement during measurement. Carefully read and repeat the

steps in section 3.3.

The batteries are low.

You should replace the batteries

with new ones ahead of time.

Refer to section 2.1.

The batteries are exhausted.

You should replace the batteries

with new ones at once.

Refer to section 2.1.

Air plug disconnected. Insert the plug securely.

Refer to section 3.1.

Arm cuff is applied too loosely. Apply the arm cuff tighter.

Refer to section 3.1.

Air is leaking from the arm cuff.

Replace the arm cuff with a new

one.

Refer to section 5.3.

Movement during measurement

and the arm cuff has not been

inflated sufficiently.

Repeat measurement. Remain

still and do not talk during

measurement.

Refer to section 3.3.

If “E2” appears repeatedly,

inflate the arm cuff manually

until it is 30 to 40 mmHg above

your previous measurement

result.

Refer to section 3.3.

The arm cuff was inflated

exceeding the maximum

allowable pressure, and then

deflated automatically when

inflating the arm cuff manually.

Do not touch the arm cuff and/or

bend the air tube while taking a

measurement. Do not inflate the

arm cuff more than necessary.

Refer to section 3.3.

Movement during measurement.

Repeat measurement. Remain

still and do not talk during

measurement.

Refer to section 3.3.

Clothing is interfering with the

arm cuff.

Remove any clothing interfering

with the arm cuff.

Refer to section 3.1.

Device error. Contact Customer Service.

Problem Cause and Solution

No power.

No display appears on the monitor.

Replace all batteries with new ones.

Check the battery installation for proper

placement of the battery polarities.

Refer to section 2.1.

Measurement values appear too high or

too low.

Blood pressure varies constantly. Many

factors including stress, time of day, and

how you wrap the cuff, may affect your

blood pressure. Review the section 1.2

and section 3.3.

Arm cuff AC Adapter

Arm circumference

9” - 17” (22 - 42 cm)

CD-WR17

(Model: HEM-RML31)

HEM-ADPTW5

Model BP742N (HEM-7131-Z)

Display LCD digital display

Measurement range Pressure: 0 to 299 mmHg

Pulse: 40 to 180 beats / min.

Accuracy Pressure: 3 mmHg or 2% of reading

Pulse:  5% of display reading

Inflation Fuzzy-logic controlled by electric pump

Deflation Automatic pressure release valve

Measurement method Oscillometric method

IP classification IP 20

Power source

4 “AA” batteries 1.5V or optional AC adapter (INPUT AC100-240V

50/60Hz 0.12A)

Battery life Approximately 1000 measurements (using new alkaline batteries)

Operating temperature

/ humidity 50°F to 104°F (10°C to 40°C) / 15 to 90% RH

Storage temperature /

humidity / air pressure

-4°F to 140°F (-20°C to 60°C) / 10 to 95% RH / 700 to 1060hPa

Weight Monitor : Approximately 10 5/8 oz. (300g) not including batteries

Arm cuff : Approximately 6 oz. (170 g)

Dimensions Monitor : Approximately 4 1/4” (w)   3 1/8” (h) 5 1/2” (l)

(107mm  79mm  141mm)

Arm cuff : Approximately 5 3/4”  23 1/2” (air tube: 29 1/2”)

(145 mm  594 mm (air tube: 750 mm))

Cuff circumference 9” to 17” (220 to 420 mm)

Memory Up to 50 per user

Contents

Monitor, arm cuff, battery set, instruction manual, quick start guide

FOR CUSTOMER SERVICE

Visit our web site at: www.omronhealthcare.com

Call toll free: 1-800-634-4350

= Type BF

Important information regarding Electro Magnetic Compatibility (EMC)

With the increased number of electronic devices such as PC’s and mobile (cellular)

telephones, medical devices in use may be susceptible to electromagnetic interference from

other devices. Electromagnetic interference may result in incorrect operation of the medical

device and create a potentially unsafe situation. Medical devices should also not interfere with

other devices.

In order to regulate the requirements for EMC (Electro Magnetic Compatibility) with the aim to

prevent unsafe product situations, the IEC60601-1-2 standard has been implemented. This

standard defines the levels of immunity to electromagnetic interferences as well as maximum

levels of electromagnetic emissions for medical devices.

Medical devices manufactured by OMRON Healthcare conform to this IEC60601-1-2:2007

standard for both immunity and emissions.

Nevertheless, special precautions need to be observed:

• The use of accessories and cables other than those specified by OMRON, with the exception

of cables sold by OMRON as replacement parts for internal components, may result in

increased emission or decreased immunity of the device.

• The medical devices should not be used adjacent to or stacked with other equipment.

In case adjacent or stacked use is necessary, the medical device should be observed to

verify normal operation in the configuration in which it will be used.

• Refer to further guidance below regarding the EMC environment in which the device should

be used.

• The MEDICAL ELECTRICAL EQUIPMENT BP742N including AC-adapter needs special

precautions regarding EMC and needs to be installed and put into service according to the

EMC information provided in this documentations.

• The Essential Performance of the BP742N including AC-adapter is to measure a blood

pressure and a pulse rate and using the memory function.

The BP742N including AC-adapter may be interfered with by other equipment, even if that

other equipment complies with CISPR EMISSION requirements.

Guidance and manufacturer’s declaration - electromagnetic immunity

OMRON BP742N including AC-adapter is intended for use in the electromagnetic environment

specified below. The customer or the user of this OMRON BP742N including AC-adapter should

assure that it is used in such environment.

Emissions test Compliance Electromagnetic environment - guidance

RF emissions

CISPR 11 Group 1

The OMRON BP742N including AC-adapter uses RF

energy only for its internal function. Therefore, its RF

emissions are very low and are not likely to cause any

interference in nearby electronic equipment.

RF emissions

CISPR 11 Class B

The OMRON BP742N including AC-adapter is suitable for

use in all establishments, including domestic

establishments and those directly connected to the public

low-voltage power supply network that supplies buildings

used for domestic purposes.

Harmonic

emissions

IEC 61000-3-2

Class A

Voltage

fluctuations/

flicker emissions

IEC61000-3-3

Complies

Guidance and manufacturer’s declaration - electromagnetic immunity

OMRON BP742N including AC-adapter is intended for use in the electromagnetic environment

specified below. The customer or the user of this OMRON BP742N including AC-adapter should

assure that it is used in such environment.

Immunity test IEC 60601 test

level Compliance level Electromagnetic environment -

guidance

Electrostatic discharge

(ESD)

IEC 61000-4-2

±6 kV contact

±8 kV air

±6 kV contact

±8 kV air

Floor should be wood, concrete,

or ceramic tile. If floors are

covered with synthetic material,

the relative humidity should be at

least 30 %.

Electrical fast

transient/burst

IEC 61000-4-4

±2 kV for power

supply lines

±1 kV for

input/output lines

±2 kV for power

supply lines

±1 kV for

input/output lines

Mains power quality should be

that of a typical commercial

and/or hospital environment.

Surge

IEC 61000-4-5

±1 kV line(s) to

line(s)

±2 kV line(s) to

earth

±1 kV line(s) to

line(s)

±2 kV line(s) to

earth

Mains power quality should be

that of a typical commercial

and/or hospital environment.

Voltage dips, short

interruptions and

voltage variations on

power supply inputlines

IEC 61000-4-11

<5 % UT (>95 % dip

in UT)

for 0.5 cycle

<5 % UT (>95 % dip

in UT)

for 0.5 cycle

Mains power quality should be

that of a typical commercial

and/or hospital environment. If the

user of the OMRON BP742N

including AC-adapter requires

continued operation during power

mains interruption, it is

recommended that the OMRON

BP742N including AC-adapter be

powered from an uninterruptible

power supply.

40 % UT (60 % dip

in UT)

for 5 cycles

40 % UT (60 % dip

in UT)

for 5 cycles

70 % UT (30 % dip

in UT)

for 25 cycles

70 % UT (30 % dip

in UT)

for 25 cycles

<5 % UT (95 % dip

in UT)

for 5 sec.

<5 % UT (95 % dip

in UT)

for 5 sec.

Power frequency

(50/60 Hz) magnetic

field

IEC 61000-4-8

3 A/m 3 A/m

Power frequency magnetic fields

should be at levels characteristic

of a typical location in a typical

commercial or hospital

environment.

Note: UT is the A.C. mains voltage prior to application of the test level.

Guidance and manufacturer’s declaration - electromagnetic immunity

OMRON BP742N including AC-adapter is intended for use in the electromagnetic environment

specified below. The customer or the user of this OMRON BP742N including AC-adapter should

assure that it is used in such environment.

Immunity test IEC 60601 test

level

Compli

ance

level

Electromagnetic environment - guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

3 V rms

150 kHz to 80

MHz

3 V/m

80 MHz to 2.5

GHz

3 V rms

3 V/m

Portable and mobile RF communications equipment

should be used no closer to any part of the OMRON

BP742N including AC-adapter including cables, than the

recommended separation distance calculated from the

equation appropriate to the frequency of the transmitter.

Recommend separation distance

d = 1.2 √P

80 MHz to 800 MHz

d = 2.3 √P

800 MHz to 2.5 GHz

where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter

manufacturer and d is the recommended separation

distance in meters (m).

Field strengths from fixed RF transmitters as determined

by an electromagnetic site survey,

a should be less than

the compliance level in each frequency range.

Interference may occur in the vicinity of equipment

marked with the following symbol:

Note1: At 80 MHz and 800 MHz, the higher frequency range applies.

Note2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption and reflection from structures, objects, and people.

a Field strengths from fixed transmitters, such as base stations for radio (cellular/ cordless) telephones

and land mobile radio, AM and FM radio broadcast, and TV broadcast cannot be predicted

theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters,

an electromagnetic site survey should be considered. If the measured field strength in the location in

which the OMRON BP742N including AC-adapter is used exceeds the applicable RF compliance

level above, the OMRON BP742N including AC-adapter should be observed to verify normal

operation. If abnormal performance is observed, additional measures may be necessary, such as

reorienting or relocating the OMRON BP742N including AC-adapter.

b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

Recommended separation distance between portable and mobile RF communications

equipment

and the OMRON BP742N including AC-adapter

OMRON BP742N including AC-adapter is intended for use in an electromagnetic environment in

which radiated RF disturbances are controlled. The customer or the user of this OMRON BP742N

including AC-adapter can help prevent electromagnetic interference by maintaining a minimum

distance between portable and mobile RF communications equipment (transmitters) and the OMRON

BP742N including AC-adapter as recommended below, according to the maximum output power of

the communications equipment.

Output Power of Transmitter in

Watt

Separation distance according to frequency of transmitter

in meter

150 kHz to 80 MHz

d = 1.2 √P

80 MHz to 800 MHz

d = 1.2 √P

800 MHz to 2.5GHz

d = 2.3 √P

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmitters rated at a maximum output power not listed above, the recommended separation

distance d in meters (m) can be estimated using the equation applicable to the frequency of the

transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to

the transmitter manufacturer.

Note: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

Note: These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption and reflection from structures, objects, and people.

Manufactured for: OMRON HEALTHCARE Co., Ltd.

53, Kunotsubo, Terado-cho, Muko, Kyoto, 617-0002 JAPAN

Distributed by: OMRON HEALTHCARE, INC.

1925 West Field Court Lake Forest, IL 60045 U.S.A.

www.omronhealthcare.com

Made in Vietnam

Produktspezifikationen

Marke:	Omron
Kategorie:	Blutdruckmessgerät
Modell:	BP742N
Display-Typ:	Analog
Herzfrequenzmonitor:	Ja
Produktfarbe:	Weiß
Display:	Ja
Typ:	Automatisch
Automatische Abschaltung:	Ja
Menge pro Packung:	1 Stück(e)
Zahl der Benutzer:	2 Benutzer
Unterstützung von Positionierung:	Oberarm
Speicherfunktion:	Ja
Pulsfrequenzmessgerät:	Nein
Handschellengröße:	23 - 43 cm
Diastolischer Blutdurck:	Nein
Systolischer Blutdruck:	Nein
Sprachfunktion:	Nein
Speicherregister:	100
Mittleren arteriellen Blutdruck:	Nein