NEC NC2000C Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NEC NC2000C (68 Seiten) in der Kategorie Beamer. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/68
NC2000C
User’s Manual
DLP Cinema® Projector
2
Precautions:
Please read this manual carefully before using your
NC2000C and keep the manual handy for future reference.
Important Safeguards
These safety instructions are to ensure the long life of your
projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT OPEN COVER. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any part inside of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in
order to avoid any problems.
CAUTION
• In order to reduce any interference with radio and television
reception use a signal cable with ferrite core attached. Use of
signal cables without a ferrite core attached may cause
interference with radio and television reception.
• This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his or her
own expense.
WARNING
This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user
may be required to take adequate measures.
DOC compliance Notice
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Important Information
Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in
accordance with EN ISO 7779.
Disposing of your used product
EU-wide legislation as implemented in each Member
State requires that used electrical and electronic
products carrying the mark (left) must be disposed
of separately from normal household waste.
This includes projectors and their electrical
accessories or lamps. When you dispose of
such products, please follow the guidance of
your local authority and/or ask the shop where
you purchased the product.
After collecting the used products, they are
reused and recycled in a proper way. This
effort will help us reduce the wastes as well
as the negative impact to the human health
and the environment at the minimum level.
The mark on the electrical and electronic products
only applies to the current European Union Member
States.
WARNING
Installation and transport
Consult your dealer for installing and transporting the projector.
DO NOT install or transport the projector by non-professional
person. Doing so may cause the lamp to break or may cause
personal injury.
• Power Supply
- Consult your dealer for installing the power cable to the
projector. DO NOT install the power cable by yourself.
Doing so may cause a fire or electric shock.
- The projector is so designed that it operates with the
power supply voltage described below.
For C1 connection
(When the AC power to the projector power supply and
the lamp power supply is provided by a single cable)
• AC 200V-240V single phase 50/60Hz
For C2 connection
(When the AC power to the projector power supply and
the lamp power supply is provided by separate cables)
• AC 100V-240V single phase 50/60Hz (projector
power supply)
• AC 200V-240V single phase 50/60Hz (lamp power
supply)
Ensure that your power supply fits this requirement
before attempting to use your projector.
- Handle the power cable carefully. A damaged or frayed
power cable can cause electric shock or fire.
• Do not bend or tug the power cable excessively.
• Do not place the power cable under the projector, or
any heavy object.
• Do not cover the power cable with other soft materials
such as rugs.
• Do not heat the power cable.
• Turn off the projector, shut down AC power by using a circuit
breaker and contact qualified service personnel under the
following conditions. For C2 connection, turn off the projec-
tor, shut down the AC power to the projector and the lamp
using a circuit breaker, and contact your dealer/distributor
for a repair.
3
- When the power cable is damaged or frayed.
- If liquid has been spilled into the projector, or if it has
been exposed to rain or water.
- If the projector does not operate normally when you
follow the instructions described in this user’s manual.
- If the projector has been dropped or the cabinet has
been damaged.
- If the projector exhibits a distinct change in performance,
indicating a need for service.
• Do not place the projector in the following conditions:
- near water, baths or damp rooms.
- on an unstable cart, stand, or table.
- in direct sunlight, near heaters or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• Do not place any liquids on top of your projector.
Refer servicing to qualified service personnel if liquid has
been spilled.
• Prevent foreign objects such as paper clips and bits of paper
from falling into your projector. Do not attempt to retrieve
any objects that might fall into your projector. Do not insert
any metal objects such as a wire or screwdriver into your
projector. If something should fall into your projector,
disconnect it immediately and have the object removed by
a qualified service personnel.
For C2 connection, turn off the projector, shut down the AC
power to the projector and the lamp using a circuit breaker,
and contact your dealer/distributor.
• Do not cover the lens with the supplied lens cap or
equivalent while the projector is on. Doing so can lead
distorting or to melting of the cap and burning your hands
due to the heat emitted from the light output.
CAUTION
• High Pressure Lamp May Explode if Improperly Handled.
Only service personnel should open the lamp door.
Refer Servicing to Qualified Service Personnel.
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• Do not touch the projector during a thunder storm. Doing
so can cause electrical shock or fire.
• Ensure that there is sufficient ventilation and that vents are
unobstructed to prevent potentially dangerous concentrations
of ozone and the build-up of heat inside your projector.
Allow at least 8 inches (20 cm) of space between your
projector and a wall. Allow at least 20 inches (50 cm) of
space between the ventilation outlet of the projector and
an object.
Connect the projector exhaust outlet with the exhaust
equipment having a capacity of 13 m3/min or more.
• Do not handle the projector and the power cable with wet
hands. Doing so can cause electrical shock or fire.
• Shut down AC power to the projector and disconnect all
the cables before moving the projector to another place.
For C2 connection, turn off the projector, shut down the
AC power to the projector and the lamp using a circuit
breaker. Disconnect the cables between devices and the
lamp before moving the projector.
• Consult your dealer for installing the power cable to the
projector. DO NOT install the power cable by yourself.
Doing so may cause a fire or electric shock.
• To carry the projector, a minimum of five persons are required.
• Do not hold the lens part and the anamorphic lens part
(or wide converter lens part) with your hand. Otherwise
the projector may tumble or drop, causing personal injury.
• If the projector will not be used for an extended period of
time, shut down AC power.
For C2 connection, turn off the projector, shut down the
AC power to the projector and the lamp using a circuit
breaker.
• Shut down AC power by using a circuit breaker before
cleaning.
For C2 connection, turn off the projector, shut down the
AC power to the projector and the lamp using a circuit
breaker.
• Do not try to touch the ventilation outlet as it can become
heated while the projector is turned on.
Doing so can lead to burning your hands due to the emitted
heat.
• When main body is damaged, cooling fluids may come out
of internal part. DO NOT touch and drink the cooling fluid.
When the cooling fluids are swallowed or contacted with
your eyes, please consult with doctors immediately.
• When using a LAN cable:
For safety, do not connect to the connector for peripheral
device wiring that might have excessive Voltage.
Installation
• Do not put the projector on its side when the lamp is on.
Doing so may cause damage to the projector.
• Handle your projector carefully. Dropping or jarring your
projector could damage internal components.
• Controlled ambient light environments will allow for an
image of higher contrast and depth to be displayed.
• Screens with a soiled, scratched, or discolored area will
not produce a clean image. Care should be used in the
handling of the screen.
• To carry the projector, a minimum of five persons are required.
Remove the lens and the lamp before carrying the projector.
Do not apply a strong shock to the projector.
• Keep finger prints or dust off the lens surface. Leaving
finger prints or dust can cause unwanted shadows on the
screen.
Cover the lens with the supplied lens cap if the projector
is not to be used for an extended period of time.
Lamp Caution: Please read before operation
• Due to the lamp being sealed in a pressurized environment,
there is a small risk of explosion, if not operated correctly.
There is minimal risk involved, if the unit is in proper working
order, but if damaged or operated beyond the recommended
hours, the risk of explosion increases. Please note that there
is a warning system built in, that displays following message
when you reach a preset operating time “Bulb Over Time”.
When you see this message please contact your dealer for a
replacement.
If the lamp does explode, smoke will be discharged from
the vents located on the back of the unit. Do not stand in
front of the vents during the operation. This smoke is
comprised of glass in particulate form and Xenon gas,
and will not cause harm if kept out of your eyes. If your
eyes have been exposed to this gas, please flush your
eyes out with water immediately and seek immediate
medical attention. Do not rub your eyes! This could cause
serious injury.
Important Information
Produktspezifikationen
| Marke: | NEC |
| Kategorie: | Beamer |
| Modell: | NC2000C |
Brauchst du Hilfe?
Wenn Sie Hilfe mit NEC NC2000C benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beamer NEC
14 Oktober 2024
5 Oktober 2024
15 September 2024
14 September 2024
14 September 2024
13 September 2024
1 September 2024
25 August 2024
20 August 2024
19 August 2024
Bedienungsanleitung Beamer
- Beamer Samsung
- Beamer 3M
- Beamer Acer
- Beamer Anker
- Beamer Asus
- Beamer Sanyo
- Beamer BenQ
- Beamer Hama
- Beamer HP
- Beamer Medion
- Beamer Philips
- Beamer Sony
- Beamer Panasonic
- Beamer LG
- Beamer OK
- Beamer Canon
- Beamer Technaxx
- Beamer Renkforce
- Beamer Blaupunkt
- Beamer Sharp
- Beamer Pyle
- Beamer Mitsubishi
- Beamer Hisense
- Beamer Salora
- Beamer Aiptek
- Beamer Auna
- Beamer Lenco
- Beamer JVC
- Beamer Optoma
- Beamer Xiaomi
- Beamer Stairville
- Beamer Smartwares
- Beamer Hitachi
- Beamer Toshiba
- Beamer Livoo
- Beamer Casio
- Beamer Epson
- Beamer ViewSonic
- Beamer Dell
- Beamer Lenovo
- Beamer Ricoh
- Beamer Smart
- Beamer Kodak
- Beamer Leica
- Beamer Adj
- Beamer Vogel's
- Beamer Eurolite
- Beamer Showtec
- Beamer Barco
- Beamer Bauer
- Beamer Eiki
- Beamer InFocus
- Beamer Nebula
- Beamer Overmax
- Beamer Marantz
- Beamer Kogan
- Beamer Acco
- Beamer Elmo
- Beamer D-Link
- Beamer Smart Tech
- Beamer Reflecta
- Beamer ZTE
- Beamer Derksen
- Beamer Cameo
- Beamer Yaber
- Beamer Vivitek
- Beamer RCA
- Beamer Promethean
- Beamer GPX
- Beamer Ibm
- Beamer La Vague
- Beamer Maxell
- Beamer Naxa
- Beamer PLUS
- Beamer Steren
- Beamer XGIMI
- Beamer Planar
- Beamer Dahua Technology
- Beamer Tzumi
- Beamer Christie
- Beamer Atlantis Land
- Beamer EKO
- Beamer Varytec
- Beamer ASK Proxima
- Beamer Beghelli
- Beamer Laserworld
- Beamer Vankyo
- Beamer AAXA Technologies
- Beamer Knoll
- Beamer Boxlight
- Beamer Miroir
- Beamer MicroVision
- Beamer Ultimea
- Beamer Dukane
- Beamer Dream Vision
- Beamer Touchjet
- Beamer AWOL Vision
- Beamer KickAss
- Beamer VAVA
- Beamer Panamorph
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024