NEC MultiSync MT600 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NEC MultiSync MT600 (32 Seiten) in der Kategorie Beamer. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/32
Part No. 78406832
Printed in Japan
NEC Multimedia Theatre
NEC Multimedia Theatre
LCD Projector
User’s Manual
NEC Technologies, Inc.
1250 N. Arlington Heights Road,Suite 500
Itasca, Illinois 60143-1248
R600
62
SPECIFICATIONS
NOTE: If failing in powering-on, the CPU returns the following
NAKs:
CA Err 1
Err 1 8X (Apply the corresponding bit.)
Bit 0: Filter cover is not attached correctly
Bit 1: Lam1p house cover is not not attached correctly
Bit 2: Overheated
Bit 3: Lamp lighting failure
12
5 4 3
6
7
8
To RxD of PC
To TxD of PC
§
To GND of PC
©
©
PC Control Connector (DIN-8P)
Cable Connection
Communication Protocol
Baud rate: 9600 bps
Data length: 8 bits
Parity: no parity
Stop bit: one bit
X on/off: none
Communications
procedure: half duplex
If the CPU of the LCD projector has received the data correctly, it
returns an ACK(C5H). If the received data is not correct, the CPU
returns a NAK(CAH), then the following status:
Receiving success: C5
Receiving failure: CA Err
Err 01: Command not supported
Err 02: Checksum error
Err 03: Command not acceptable(Busy)
Err 04: Parameter error
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABI-
NET. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage
within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind
of contact with any part inside of the unit.
This symbol alerts the user that important informa-
tion concerning the operation and maintenance of
this unit has been provided. The information should
be read carefully to avoid problems.
I M P O R T A N T I N F O R M A T I O N
Precautions
Please read this manual carefully before using your NEC
MultiSync MT600 LCD Projector and keep the manual handy for
future reference.
Your serial number is located on the side of your MultiSync MT600,
below the cooling fan vent.Record it here:
____________________________________________________________
CAUTION
RISK OF ELECTRIC SHOCKDO NOT OPEN
1
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified by
NEC Technologies in this manual. Failure to comply with this
government regulation could void your right to operate this equip-
ment.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a commercial installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
2
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S
GROUNDED PLUG WITH AN EXTENSION CORD OR IN
AN OUTLET UNLESS ALL THREE PRONGS CAN BE
FULLY INSERTED. DO NOT OPEN THE CABINET. THERE
ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SER-
VICING MUST BE DONE BY QUALIFIED NEC SERVICE
PERSONNEL.
Command Codes (continued)
No. Function Code Data Description
33 Lamp Reset 27H No Lamp usage hour is reset to 0
34 S-VIDEO C6H No Same as remote
35 Brightness 60H Yes 0 to 63
36 Contrast 62H Yes 0 to 63
37 Color 64H Yes 0 to 63
38 Tint 66H Yes -32 to +31(E0 to 1F)
39 Sharpness 68H Yes 0 to 3
40 Audio Volume 6AH Yes 0 to 63
41 Fine Picture 6EH Yes 0 to 15
42 Picture Adj 70H Yes 0 to 255
43 H Position 72H Yes -32 to +31(E0 to 1F)
44 V Position 74H Yes -32 to +31(E0 to 1F)
61
Produktspezifikationen
| Marke: | NEC |
| Kategorie: | Beamer |
| Modell: | MultiSync MT600 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit NEC MultiSync MT600 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beamer NEC
14 Oktober 2024
5 Oktober 2024
15 September 2024
14 September 2024
14 September 2024
13 September 2024
1 September 2024
25 August 2024
20 August 2024
19 August 2024
Bedienungsanleitung Beamer
- Beamer Samsung
- Beamer 3M
- Beamer Acer
- Beamer Anker
- Beamer Asus
- Beamer Sanyo
- Beamer BenQ
- Beamer Hama
- Beamer HP
- Beamer Medion
- Beamer Philips
- Beamer Sony
- Beamer Panasonic
- Beamer LG
- Beamer OK
- Beamer Canon
- Beamer Technaxx
- Beamer Renkforce
- Beamer Blaupunkt
- Beamer Sharp
- Beamer Pyle
- Beamer Mitsubishi
- Beamer Hisense
- Beamer Salora
- Beamer Aiptek
- Beamer Auna
- Beamer Lenco
- Beamer JVC
- Beamer Optoma
- Beamer Xiaomi
- Beamer Stairville
- Beamer Smartwares
- Beamer Hitachi
- Beamer Toshiba
- Beamer Livoo
- Beamer Casio
- Beamer Epson
- Beamer ViewSonic
- Beamer Dell
- Beamer Lenovo
- Beamer Ricoh
- Beamer Smart
- Beamer Kodak
- Beamer Leica
- Beamer Adj
- Beamer Vogel's
- Beamer Eurolite
- Beamer Showtec
- Beamer Barco
- Beamer Bauer
- Beamer Eiki
- Beamer InFocus
- Beamer Nebula
- Beamer Overmax
- Beamer Marantz
- Beamer Kogan
- Beamer Acco
- Beamer Elmo
- Beamer D-Link
- Beamer Smart Tech
- Beamer Reflecta
- Beamer ZTE
- Beamer Derksen
- Beamer Cameo
- Beamer Yaber
- Beamer Vivitek
- Beamer RCA
- Beamer Promethean
- Beamer GPX
- Beamer Ibm
- Beamer La Vague
- Beamer Maxell
- Beamer Naxa
- Beamer PLUS
- Beamer Steren
- Beamer XGIMI
- Beamer Planar
- Beamer Dahua Technology
- Beamer Tzumi
- Beamer Christie
- Beamer Atlantis Land
- Beamer EKO
- Beamer Varytec
- Beamer ASK Proxima
- Beamer Beghelli
- Beamer Laserworld
- Beamer Vankyo
- Beamer AAXA Technologies
- Beamer Knoll
- Beamer Boxlight
- Beamer Miroir
- Beamer MicroVision
- Beamer Ultimea
- Beamer Dukane
- Beamer Dream Vision
- Beamer Touchjet
- Beamer AWOL Vision
- Beamer KickAss
- Beamer VAVA
- Beamer Panamorph
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024