NAD MDC DAC Bedienungsanleitung

NAD Hi-Fi-Anlage MDC DAC

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr NAD MDC DAC (2 Seiten) in der Kategorie Hi-Fi-Anlage. Dieser Bedienungsanleitung war fĂĽr 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
®
ASYNCHRONOUS USB DAC MODULE
Mounting Instructions
MOUNTING INSTRUCTIONS FOR THE C375BEE
The DAC Module is compatible with C375BEE. Using the supplied exible at
cable (FFC), DC power connector and screws, the DAC Module can be installed
in a C375BEE by undertaking the following procedure.
Note that if the C375BEE has a PP375 Phono Preamplier Module already
installed, the DAC module and the PP375 can be linked together using the other
supplied FFC.
STEP 1
Pre-install the requisite cables to their respective connector points on the DAC
Module as shown. Connect the FFC to the DAC Module’s PP375 IN only if the
C375BEE has a PP375 already installed.
STEP 2
Make the following connections:
1 DC POWER connector from DAC Module to corresponding P216B in
C375BEE’s main board.
2 FFC from DAC Module’s ANALOG OUT to P213B on C375BEE’s main board.
3 If the optional PP375 module is installed: FFC from DAC Module’s PP375 IN
to the corresponding FPC (exible printed circuit) connector of the PP375
module.
Ensure good harnessing by exing and safely contorting the FFC and
DCPOWER connectors.
STEP 3
Remove the dummy cover at the back of the C375BEE and install in its place the
DAC Module. Use the supplied screws to x into place the DAC Module.
3
2
1
IMPORTANT!
The DAC module is only compatible with C 375BEE units that have the
0.5Wstandby logo on their rear panels.
©2015 NAD ELECTRONICS INTERNATIONAL, A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
MDCDAC_QS_V06  04/15
1
2
MOUNTING INSTRUCTION FOR THE C356BEE
The DAC Module is compatible with C356BEE. Using the supplied exible at
cable (FFC), DC power connector and screws, the DAC Module can be installed
in a C356BEE by undertaking the following procedure.
STEP 1
Pre-install the requisite cables to their respective connector points.
Connect the following
1 DC POWER connector from DAC Module to corresponding CB48 on
C356BEE’s main board.
2 FFC from DAC Module’s ANALOG OUT to CB36 on C356BEE’s main board.
Ensure good harnessing by exing and safely contorting the FFC and DC POWER
connectors.
STEP 2
Remove the dummy cover at the back of the C356BEE and install in its place the
DAC Module. Use the supplied screws to x into place the DAC Module.


Produktspezifikationen

Marke: NAD
Kategorie: Hi-Fi-Anlage
Modell: MDC DAC

Brauchst du Hilfe?

Wenn Sie Hilfe mit NAD MDC DAC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Hi-Fi-Anlage NAD

Bedienungsanleitung Hi-Fi-Anlage

Neueste Bedienungsanleitung fĂĽr -Kategorien-