Motorola MBP10L Bedienungsanleitung

Motorola Babyphone MBP10L

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Motorola MBP10L (4 Seiten) in der Kategorie Babyphone. Dieser Bedienungsanleitung war für 48 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
8765
F N
ID
13
14
15
16
12
Overview of your Baby unit
C
Back of baby unit, no
serviceable parts.
D
12. Power LED
13. Power On/Off
button A
14. Microphone
15. Paging button B
16. Power adapter
connector
1. Safety Instructions
WARNING
This baby monitor is compliant with all relevant standards regarding electromagnetic
fields and is, when handled as described in the User’s Guide, safe to use. Therefore,
always read the instructions in this User’s Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children when assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this User’s Guide for future reference.
• Do not place the baby unit or cables in the crib or within arm's reach of the baby
(the unit should be at least 3 feet away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power adapters
provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do not use other chargers
or power adapters as this may damage the device and batteries.
• For the parent unit, only insert a rechargeable battery pack of the same type.
• Do not touch the charger or plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
2. Getting Started
2.1 Baby unit power supply
1. Connect the small plug of the power adapter to the power connector on the
baby unit and the other end of the adapter to the electrical outlet (110V/60Hz).
NOTE
Only use the enclosed power adapter (6V DC / 300mA).
2. Press A. The Power LED will illuminate.
3. Press and hold A to switch off the baby unit.
2.2 Parent unit battery installation
The Parent unit can be used with either the rechargeable battery pack (2.4V
600mAh Ni-MH rechargeable battery pack supplied) or via the power adapter
supplied.
NOTE
The Ni-MH rechargeable battery pack must be charged for 15 hours before using
the Parent unit without the power supply.
We recommend installing the rechargeable battery pack, so that the unit continues
to work in the event of a power outage.
1. Using a screwdriver, turn the screw of the battery cover on the back of the parent
unit counterclockwise 90 degrees to remove the battery cover.
NOTE
Rotate the belt clip to its hanging position to make it easier to access the battery
compartment.
Do not try to turn the screw further than the
OPEN
position marked on the cover.
2. Fit the Ni-MH rechargeable battery pack in the compartment as shown above.
3. Close the battery compartment and turn the screw back 90 degrees.
+
-
+
-
4. Press P. The Power (ON / ) LED will illuminate green if it only has
battery power.
5. Press and hold P to switch off the parent unit.
NOTE
When the battery level is low, the green power LED will flash and the parent unit
will emit a warning beep once every minute. If the baby unit loses power or goes
out of range, the link will be lost and the parent unit will emit a warning beep every
3 seconds and the green link LED on the parent unit will continue to flash.
WARNING
Keep battery pack away from small children.
Do not short-circuit battery pack or dispose of in fire.
Remove the battery pack if this device is not going to be used for a long period of time.
2.3 Parent unit power supply
1. Connect the small plug of the power adapter to the power connector on the
parent unit and the other end of the adapter to the electrical outlet (110V/60Hz).
NOTE
Only use the enclosed adapter (6V DC / 300mA).
2. Press P. The Power (ON / ) LED will illuminate red when it is connected
to the power supply.
3. Press and hold P to switch off the parent unit.
2.4 Link
NOTE
Do not place the baby unit or the unit's cord in the crib or within arm's reach of the
baby (the unit should be at least 3 feet away).
When using the baby monitor for the first time, it is advised to test the connection.
• Install the parent unit in the same room as the baby unit, but make sure there
are at least 3 feet between the 2 units.
• When both units are switched on, the parent unit will search for the baby unit.
Table of contents
1. Safety Instructions........................................................................ 6
2. Getting Started .............................................................................. 6
2.1 Baby unit power supply ................................................................ 6
2.2 Parent unit battery installation ...................................................... 7
2.3 Parent unit power supply.............................................................. 8
2.4 Link............................................................................................... 8
2.5 Registration .................................................................................. 9
2.6 Paging .......................................................................................... 9
3. Using the MBP10, MBP10L........................................................... 9
3.1 Volume adjustment on the Parent unit ......................................... 9
4. Disposal of the Device in the Environment .............................. 10
5. Cleaning ....................................................................................... 10
6. Help .............................................................................................. 11
7. General Information .................................................................... 11
1
2
3
4
5
6
7
8
1. Link indicator LED
2. Volume down
button M
3. Power On/Off
button P
4. Speaker
5. Volume up
button O
6. Power (ON / )
LED
7. Volume indicator
LEDs
8. Power adapter
connector
Overview of your Parent unit
B9. Belt clip
10. Battery cover screw
11. Battery cover
A
This User’s Guide provides you with all the information you need to get
the most from your product.
Before you can use the baby monitor, you’ll need to insert and fully
charge the battery on the Parent unit. Please read the Safety
Instructions in section 1 “Safety Instructions” before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit
• 1 x Rechargeable battery pack for the Parent unit
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
Welcome...
to your new Motorola Digital Baby Monitor!
Thank you for purchasing the MBP10, MBP10L. This baby monitor uses
digital communication which ensures that you can hear your baby
clearly without any distracting noise or interference.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide a
copy of your dated sales receipt to confirm warranty status. Registration
is not required for warranty coverage.
For product related questions, please call:
1-888-331-3383 in US and Canada
On the Web: www.motorola.com
USER’S GUIDE
MBP10, MBP10L
DIGITAL BABY MONITOR
The features described in this user’s guide are subject to
modifications without prior notice.
9 10 11 12
13 14 15
NOTE
When you press ( or ) a beep is played at the volume level currently set, but if
you try to adjust beyond the maximum or minimum levels it will output a double
beep.
4. Disposal of the Device in the
Environment
At the end of the product lifecycle, you should not dispose of this
product with normal household waste, but take the product to a
collection point for the recycling of electrical and electronic equipment.
The symbol on the product, User’s Guide and/or box indicates this.
Some of the product materials can be re-used if you take them to a
recycling point. By reusing some parts or raw materials from used
products you make an important contribution to the protection of the environment.
Please contact your local authorities in case you need more information on the
collection points in your area.
Dispose of the batteries in an environmentally-friendly manner according to your
local regulations.
5. Cleaning
Clean the MBP10, MBP10L with a slightly damp cloth or with an anti-static cloth.
Never use cleaning agents or abrasive solvents.
Cleaning and care
• Do not clean any part of the product with thinners or other solvents and
chemicals –- this may cause permanent damage to the product which is not
covered by the warranty. When necessary, clean it with a damp cloth.
• Keep your MBP10, MBP10L away from hot, humid areas or strong sunlight,
and do not let it get wet.
• Every effort has been made to ensure high standards of reliability for your
MBP10, MBP10L. However, if something does go wrong, please do not try to
repair it yourself –- consult Customer Service for assistance.
6. Help
Registration
If the baby unit has lost its link with the parent unit
• Try recharging or replacing the battery pack.
• If the baby unit is too far away it may be going out of range, so move the baby
unit closer to the parent unit.
• Reset the units by unplugging the units’ electrical power. Wait for around 15
seconds and plug them back in again. Allow up to one minute for the baby unit
and the parent unit to synchronize.
• See “2.5 Registration” if there is a need to re-register the units.
Interference
Noise interference on your parent unit
• The units may be too close. Move them further away from each other.
• Make sure there are at least 3 feet between the 2 units to avoid audio feedback.
• If the baby unit is too far away it may be going out of range, so move the baby
unit closer to the parent unit.
• Make sure the units are not near other electrical equipment, such as a
television, computer or cordless/mobile telephone.
7. General Information
If your product is not working properly....
1. Read this User’s Guide or the Quick Start Guide.
2. Visit our website: http://www.motorola.com
3. Contact Customer Service at 1-888-331-3383 in US and Canada.
To order a replacement battery pack, contact customer service or visit our website.
Consumer Products and Accessories purchased in the
United States or Canada
What Does this Warranty Cover?
Subject to the exclusions and limitations contained below, Binatone Electronics
International LTD. warrants the Motorola branded consumer products that it
manufactures (“Products”) and the Motorola branded or certified accessories sold for
use with these Products that it manufactures (“Accessories”) to be free from defects
in materials and workmanship under normal consumer usage for the period(s)
outlined below. This limited warranty is a consumer’s exclusive remedy, and only
applies as follows to new Motorola branded Products and Accessories manufactured
by Binatone Electronics International LTD., and purchased by consumers in the
United States or Canada, which are accompanied by this written warranty:
Who is covered?
This warranty covers only the first consumer purchaser, and is not transferable.
What will BINATONE ELECTRONICS INTERNATIONAL LTD. do?
BINATONE ELECTRONICS INTERNATIONAL LTD., at its sole option, will at no
charge repair, replace or refund the purchase price of any Products or Accessories
that does not conform to this warranty. Binatone Electronics International LTD. may
use functionally equivalent reconditioned/ refurbished/ pre-owned or new Products,
Accessories or parts in such repair or replacement and any Products, Accessories
or parts removed or being replaced under this warranty become the property of
Binatone Electronics International LTD.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES OR CONDITIONS IRRESPECTIVE OF WHETHER
THEY ARE IMPOSED BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND
IS PROVIDED IN LIEU OF ALL WARRANTIES AND MOTOROLA AND
BINATONE ELECTRONICS INTERNATIONAL LTD. MAKES NO OTHER
WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED. IN NO EVENT
SHALL MOTOROLA OR BINATONE ELECTRONICS INTERNATIONAL LTD. BE
LIABLE, WHETHER UNDER THIS LIMITED WARRANTY OR IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE OR STRICT PRODUCT LIABILITY) OR
OTHERWISE FOR DAMAGES OR CLAIMS IN EXCESS OF THE PURCHASE
PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE, SAVINGS OR PROFITS, LOSS OF BUSINESS, LOSS OF
PROGRAMS DATA INFORMATION (WHETHER CONFIDENTIAL
PROPRIETARY OR PERSONAL IN NATURE OR OTHERWISE) OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY
OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES AND BINATONE
ELECTRONICS INTERNATIONAL LTD. SHALL UNDER NO CIRCUMSTANCES
• The green link LED on the parent unit will flash until the parent unit is
connected with the baby unit.
Once the link is established, the LED will stop flashing.
• The sound captured by the microphone on the baby unit will be audible on the
parent unit.
• The detected sound level is indicated by the LEDs on the front of the parent unit.
• When the connection is established, move the parent unit to the room you want
to monitor from, but within the operational range.
• When there is no connection or if the units are out of range, the parent unit
emits a warning beep every 3 seconds and the green link LED on the parent
unit will flash.
• Move the parent unit closer until the link is re-established.
2.5 Registration
The baby monitor is already pre-registered upon your purchase. You do not need
to register it again unless the baby unit loses its link with the parent unit.
To re-register your baby monitor, follow the procedure below:
1. Disconnect the power supply for both the baby and parent units, and remove
the battery pack from the parent unit.
2. Press and hold A for 3 seconds as you reconnect the power supply of
the baby unit. The baby unit is in registration mode.
3. Press and hold P as you reconnect the power supply of the parent unit,
and keep holding it down until the red sound LEDs flash. The parent unit is in
registration mode.
4. Wait for the 2 units to search and establish the link.
When the registration is complete, the LEDs stop flashing and the parent unit emits
a long beep.
2.6 Paging
If the parent unit is misplaced, press and hold B on the baby unit for 2 seconds.
The parent unit will emit a repeated beep tone for 30 seconds so that you can
locate it.
Press any key on the parent unit, or the B again on the Baby unit, to stop paging.
3. Using the MBP10, MBP10L
3.1 Volume adjustment on the Parent unit
There are 5 volume levels on the parent unit.
• Press ( to increase the volume level.
• Press ) to decrease the volume level.
evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming
or non-Motorola branded housings, or parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of Products or
Accessories due to any communication service or signal you may subscribe to or
use with the Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
1-888-331-3383 in US and Canada
You will receive instructions on how to ship the Products or Accessories, the
shipment of which shall be at your own risk and expense, to a BINATONE
ELECTRONICS INTERNATIONAL LTD. Authorized Repair Center. To obtain
service, you must include: (a) a copy of your receipt, bill of sale or other comparable
proof of purchase of the Products or Accessories showing the date of purchase; (b)
a written description of the problem; and, most importantly; (c) your address and
telephone number.
These terms and conditions constitute the complete warranty agreement between
you and BINATONE ELECTRONICS INTERNATIONAL LTD. regarding the
Products or Accessories purchased by you, and supersede any prior agreement or
representations, including representations made in any literature publications or
promotional materials issued by BINATONE ELECTRONICS INTERNATIONAL
LTD. or representations made by any agent employee or staff of BINATONE
ELECTRONICS INTERNATIONAL LTD., that may have been made in connection
with the said purchase.
FCC and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Privacy of communications may not be ensured
when using this device.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to
the intended usage of the product. This product has been tested and found to
comply with the FCC criteria. The Baby unit shall be installed and used such that
parts of the user's body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
WARNING
Changes or modifications to this equipment not expressively approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
The term "IC: " before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
This product meets the applicable Industry Canada technical specifications.
RENSEIGNEMENTS RELATIFS AUX RÈGLEMENTS DE LA
COMMISSION FÉDÉRALE DES COMMUNICATIONS 'FCC',
ET D'INDUSTRIE Canada 'IC'
Article 15 des règlements du FCC
AVIS: Cet équipement a été testé et s'est révelé conforme aux limites d'un appareil
numérique de classe B, conformément à la Section 15 du réglement de la Federal
Communications Commission (FCC). Ces limites sont conçues pour offrir une
protection raisonnable contre toute interférence nuisible sur une installation
résidentielle. Cet appareil génère, utilise et peut émettre des fréquences radio et s'il
n'est pas installé selon les instructions, peut nuire aux radiocommunications. Toutefois,
rien ne garantit que des parasites ne surviendront pas dans une installation particulière.
Si cet appareil cause des interférences nuisibles à la réception du téléviseur ou de la
radio, ce que vous pouvez déterminer en mettant votre appareil en et hors fonction,
nous vous invitons à essayer l'une des mesures correctives suivantes :
• Réorientez l'antenne de réception.
• Éloignez l'appareil du composant qui reçoit les ondes.
• Branchez l'appareil dans une prise de courant CA différente de celle du
composant qui reçoit les ondes.
• Au besoin, consultez votre marchand électronique ou un technicien spécialisé
dans le service des radios/téléviseurs pour des suggestions supplémentaires.
Toute modification ou changement effectué à cet appareil sans l'accord des parties
responsables de l'homologation peut retirer à l'utilisateur son droit d'utiliser l'appareil.
Cet appareil est conforme à l'article 15 de la FCC. Le fonctionnement est soumis
aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences
nuisibles et; (2) Il doit pouvoir supporter les parasites qu'il reçoit, incluant les
parasites pouvant nuire à son fonctionnement. La confidentialité des
communications peut ne pas être assurée avec cet appareil.
Afin de garantir la sécurité des utilisateurs, la FCC a établi les critères relatifs à
l'énergie générée par les fréquences radio pouvant être absorbée en toute sécurité
par un utilisateur ou par quelqu'un se trouvant à proximité, dépendamment de
l'utilisation prévue du produit. Ce produit a été testé et s'avère conforme aux
normes de la FCC. L'unité du bébé devra être installée et utilisée de manière à ce
que le corps de l'utilisateur, à l'exception des mains, soit toujours à une distance
d'environ 20 cm (8 po.) ou plus.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
AVERTISSEMENT
Tout changement ou modification à cet équipement, non expressement autorisé
par la partie responsable de la conformité, pourrait annuler l'autorisation donnée à
l'utilisateur d'utiliser cet équipement.
Industrie Canada
Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit
pas causer d'interférences nuisibles et; (2) Cet appareil accepte toute les interférences
dont celles qui pourraient provoquer le fonctionnement involontaire de l'appareil.
L'abréviation 'IC' se trouvant avant cette homologation signifie que la certification
fut effectuée selon une déclaration de conformité spécifiant que les normes
d'Industrie Canada ont été rencontrées.
Cet appareil est conforme aux spécifications techniques d'Industrie Canada.
Technical Specifications
Frequency range 2.4GHz to 2.4835GHz
(bandwidth = 83.5MHz)
Operating range Extended range up to 950 feet*
*Based on unobstructed line of sight. Actual range will vary
depending on surroundings.
Electrical power Parent and Baby units:
Input — 100-240VAC, 50/60Hz (USA plug);
Output — 6VDC, 300 mA (Supplier: Kings,
Model: KSS05-060-0300U)
Parent unit:
2.4V 600mAh Ni-MH rechargeable battery pack
(Supplier: GPI, Model: GP60AAAH2BXZ)
BE LIABLE FOR ANY CLAIMS OR DEMANDS MADE BY ANY THIRD PARTY OR
MADE BY YOU ON BEHALF OF ANY THIRD PARTY TO THE FULL EXTENT
THESE DAMAGES OR CLAIMS MAY BE DISCLAIMED BY LAW.
Some states, countries or jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the length of an implied
warranty, so the above limitations or exclusions may not apply to you in such
states, countries or jurisdictions. This warranty gives you specific legal rights, and
you may also have other rights that vary from state to state or from one country/
jurisdiction to another.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement of parts
due to normal wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of their rated
capacity and batteries that leak are covered by this limited warranty. Battery life and
the changes in battery capacity with time or use are excluded from this warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper or
unreasonable use, operation, storage, misuse or abuse, accident or neglect or
other external cause, such as physical damage (cracks, scratches, etc.) to the
surface of the product resulting from misuse; (b) your failure to follow or operate
outside the usage parameters stated in the user instructions that came with the
Products or Accessories; (c) contact with liquid, water, rain, extreme humidity or
heavy perspiration, sand, dirt or the like, extreme heat, or food; (d) use of the
Products or Accessories for commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (e) other acts or omissions which
are not the fault or neglect of Motorola or Binatone Electronics International LTD.,
are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects or damage
that result from the use of Non-Motorola branded or certified Products or
Accessories or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages resulting from
service, testing, adjustment, installation, maintenance, alteration, or modification in
any way by someone other than Motorola, Binatone Electronics International LTD.
or its authorized service centers, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or date tags
that have been removed, altered or obliterated; (b) broken seals or that show
Products or Accessories Covered Length of Coverage
Consumer Products One (1) year from the date of purchase by
the first consumer purchaser of the
product.
Consumer Accessories Ninety (90) days from the date of
purchase by the first consumer purchaser
of the accessory.
Consumer Products and
Accessories that are Repaired or
Replaced
The balance of the original warranty or
for ninety (90) days from the date
returned to the consumer, whichever is
longer.
Manufactured, distributed or sold by Binatone Electronics International LTD., official licensee
for this product. MOTOROLA and the Stylized M Logo, and other Motorola trademarks and
trade dress are owned by Motorola, Inc. and are used under license from Motorola, Inc.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.
A
ll other product or service names are the property of their respective owners.
© Motorola, Inc. 2010. All rights reserved.
Printed in China
Version 1.0

Produktspezifikationen

Marke: Motorola
Kategorie: Babyphone
Modell: MBP10L

Brauchst du Hilfe?

Wenn Sie Hilfe mit Motorola MBP10L benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Babyphone Motorola

Motorola

Motorola MBP36BU Bedienungsanleitung

8 September 2024
Motorola

Motorola VM50G-2 Bedienungsanleitung

31 August 2024
Motorola

Motorola PIP1510-2 CONNECT Bedienungsanleitung

31 August 2024
Motorola

Motorola PIP1510 CONNECT Bedienungsanleitung

31 August 2024
Motorola

Motorola PIP 1010 Connect Bedienungsanleitung

23 August 2024
Motorola

Motorola EASE35 Bedienungsanleitung

23 August 2024
Motorola

Motorola MBP667 Bedienungsanleitung

22 August 2024
Motorola

Motorola VM55 Bedienungsanleitung

22 August 2024
Motorola

Motorola VM35 Bedienungsanleitung

16 August 2024
Motorola

Motorola VM482 Bedienungsanleitung

16 August 2024

Bedienungsanleitung Babyphone

Neueste Bedienungsanleitung für -Kategorien-

Alecto

Alecto DBX-72 ECO Bedienungsanleitung

9 Oktober 2024
Reer

Reer Neo 200 Bedienungsanleitung

8 Oktober 2024
Babymoov

Babymoov High Care A014009 Bedienungsanleitung

7 Oktober 2024
Topcom

Topcom KS-4241 Bedienungsanleitung

3 Oktober 2024
Lorex

Lorex BB1811 Bedienungsanleitung

2 Oktober 2024
Vtech

Vtech Clear Sounds Deluxe Bedienungsanleitung

2 Oktober 2024
Alecto

Alecto DVM-75C Bedienungsanleitung

2 Oktober 2024
TrueLife

TrueLife NannyCam V24 Pro Bedienungsanleitung

1 Oktober 2024
TrueLife

TrueLife NannyCam H32 Pro Bedienungsanleitung

1 Oktober 2024
Uniden

Uniden GC43W Bedienungsanleitung

30 September 2024