Motorola C1002LX Bedienungsanleitung

Motorola Schnurlose DECT-Telefone C1002LX

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Motorola C1002LX (2 Seiten) in der Kategorie Schnurlose DECT-Telefone. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Connecting the base
1. Plug the telephone line cord into the socket marked on the rear
of the base.
2. Plug the power adapter into the socket marked on the rear of
the base and plug the other end into the electrical outlet.
Charging the handset
3. If you are charging the battery for the rst time, place the handset
on the base to charge for at least 24 hours continuously.
4. When the handset is fully charged, icon will appear steady
on the display. Plug the other end of the telephone line cord
(make sure that one end is already plugged into the base) into the
telephone wall socket.
Connecting the handset and charger
(for multi-pack only)
If you have purchased a multiple pack, you will need to carry out this
process for all the handsets and chargers.
1. Plug the power adapter into the socket marked on the rear of
the charger and plug the other end into an electrical outlet.
4. Press , scroll to select the volume (1 -5 or OFF) .mu or d
5. Press to conrm or mb to return to the previous menu.
5.1.2 Ringer tones
You can set dierent ringer tones for your internal and external calls.
Choose from 10 dierent ringer tones.
NOTE
You will hear a sample ring as you scroll to each ring tone.
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Press . Scroll md to
Ring tones
.
4. Press , scroll to select the tone (1 -10) .mu or d
5. Press to conrm or mb to return to the previous menu.
5.1.3 Key tones on/o
When you press a button on the handset keypad, you will hear a beep.
You can switch these beeps on or o.
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Press . Scroll md to
Key tone
.
4. Press , mu or d to select
On
or
O
and press m to conrm.
5.1.4 Docking tone on /o
When you replace the handset in the base you will hear a double beep.
You can switch this beep on or o.
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Press . Scroll md to
Docking tone
.
4. Press , mu or d to select
On
or
O
and press m to conrm.
4.3 Edit a name and number
1. Press twice. The display shows m
View
.
2. Scroll d to
Edit
and press .m
3. Scroll to the entry you want to edit, or search alphabetically u or d
and press . The existing name is displayed.m
4. to delete the name if required, then enter the new name Press b
and press . The existing number is displayed.m
5. to delete the number if required, then enter the new Press b
number and press m to save.
4.4 Delete an entry
1. Press twice. The display shows m
View
.
2. Scroll d to
Delete
and press .m
3. Scroll to the entry you want to delete, or search u or d
alphabetically and press . The display shows m
Conrm?
.
4. Press to conrm or mb to cancel.
4.5 Delete all entries
1. Press twice. The display shows m
View
.
2. Scroll d to
Delete all
and press .m
3. The display shows
Conrm?
.
4. Press to conrm or mb to cancel.
5. Personal settings
5.1 Sounds
5.1.1 Ring volume
You can adjust the ringer volume and set dierent volume levels. Choose
from 5 volume levels or O.
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Press . The display shows m
Ring volume
.
4. Phonebook
The C100xLX handset phonebook can store up to 50 names and
numbers.
Names can be up to 14 characters long and numbers up to 24 digits.
4.1 Store a name and number
1. Press . m
Phonebook
is displayed.
2. Press . m
New Entry
is displayed.
3. Press . m
Enter Name
is displayed.
4. Enter a name and press . m
5. Enter a number. Press m to save.
6. Press e to return to standby.
ENTERING NAMES
Use the keypad letters to enter names, e.g. to store TOM:
Press once to enter T.8
Press 6 three times to enter O.
Press once to enter M.6
WRITING TIPS
Press to delete the last character or digit.b
Press to move between characters.u or d
Press to insert a space.0
4.2 View or dial an entry
1. .Press u
2. Scroll u or d to the entry you want.
OR
Enter the rst letter of the name to search alphabetically.
The rst name that starts with this letter or the nearest letter in the
alphabet will be
displayed. Scroll u or d to the entry you want.
3. Press to dial or t e to return to standby.
3.7.3 Delete an entry
1. Press to open the Redial list.r
2. Scroll u or d to the entry you want. Press m.
3. Scroll d to
Delete
and press . The display shows m
Conrm?
.
4. Press to conrm or mb to cancel.
3.7.4 Delete the entire Redial list
1. Press to open the Redial list.r
2. Press . Scroll md to
Delete all
. The display shows
Conrm?
.
3. Press to conrm or mb to cancel.
3.8 Lock / unlock the keypad
When the keypad is locked, you can still answer incoming calls and
operate the handset normally during a call. When the call ends, the
keypad lock resumes in place.
NOTE
When the keypad is locked, you can still answer incoming calls and
operate the handset normally during a call. When the call ends, the
keypad lock resumes in place.
1. Press and hold . 0
Keys locked
is displayed.
2. To unlock the keypad, press and hold again.0
3.9 Paging / Find handset
Paging is a useful way to nd lost handsets.
1. Press on the base. All handsets ring.p
2. Press again to cancel the paging call or press any key on the p
handset to stop the paging call.
2. If more than 2 handsets are registered to the base press and hold
* and scroll to the handset that is to join the call and press .dm
3. When the other handset answers, press m to connect all three
callers to begin the conference call.
4. Press e to end the call.
3.6 Hands-free
To talk to the caller without holding the handset or for other people in
the room to listen to the conversation over the loudspeaker simply use
the hands-free function.
3.6.1 Make a hands-free call
1. Dial the number and then press .h
2. Press e to end the call.
3.6.2 Answer a call hands-free
Press to answer the call in hands-free.h
NOTE
Press to switch the call between the earpiece and the loudspeaker.h
During a hands-free call, press u or d to adjust the volume.
3.7 Redial
The last 10 entries dialed are stored in the redial list.
3.7.1 View or dial an entry
1. Press to open the Redial list.r
2. Scroll u or d to the entry you want.
3. Press t to dial the displayed entry or press e to return to standby.
3.7.2 Copy a Redial list number to the phonebook
1. Press to open the Redial list.r
2. Scroll u or d to the entry you want.
3. Press . The display shows m
Save number
.
4. Press again. The display shows m
Enter name
.
5. Enter the name and press . The number is displayed.m
6. Edit the number if necessary, then press m to save.
3.5 Intercom
3.5.1 Make an internal call
If more than one handset is registered to the base, internal calls can be
made between two handsets. icon flashes and the display shows the
handset number you are calling.
1. If only 2 handsets are registered to the base, press and the other *
handset rings automatically.
2. If more than 2 handset are registered to the base press and *
scroll to the handset that is to be called and press dt.
3.5.2 Receive an internal call
When you receive an internal call, icon flashes and the handset
number that is calling you is displayed.
1. Press to make an internal call.t
3.5.3 Transfer a call
You can transfer an external call to another handset registered to the
base.
During an external call:
1. If only 2 handsets are registered to the base, press and hold and *
the other handset rings automatically.
2. If more than 2 handsets are registered to the base press and hold
* and scroll to the handset that is to be called and press .dm
3. When the other handset answers, press e to complete the transfer.
NOTE
Your external call resumes automatically after 1 minute if there is no
answer.
3.5.4 3-way conference call
You can hold a 3-way conference call between 2 internal callers and 1
external caller.
During a call with an external caller:
1. If only 2 handsets are registered to the base, press and hold and *
the other handset rings automatically.
After charging your handset for the rst time, subsequent charging time
is about 6–8 hours a day. The battery and handset may become warm
during charging. This is normal.
1All talk and standby times are approximate and depend on features
selected and usage pattern.
Date and time
If you have subscribed to a Caller ID Service and the Auto Clock is set
to on, the date and time will set automatically for all handsets when you
receive your rst call.
If you do not have a Caller ID service, you can set the date and time
manually, see section “5.3. Date and Time”.
Your C100xLX is now ready for use.
2. Getting to know your phone
Underside of your base
A
A Page
In standby mode, press to ring the handset(s).
Press and hold to enter registration mode when registering
handsets.
Handset display
Display icons
Indicates signal strength.
Flashes when the handset is not registered to the base or if you are
out of range.
Indicates a missed call.
Steady when making an outgoing call.
Flashes to indicate an incoming or internal call.
Indicates an incoming call when viewing the calls list.
Indicates an outgoing call when viewing the calls list.
Hands-free is on.
Handset ringer is o.
Indicates new voicemail messages received .
1
O when there is no voicemail messages.
pq Indicates you can scroll through a list or adjust the volume in talk mode.
uIndicates more text after the displayed information.
fBattery is fully charged.
HBattery is partially charged.
lBattery is running low.
EFlashes when battery is almost fully discharged.
Overview of your handset 1This feature is dependent on your Network Service provider supporting
the service. A subscription fee may be payable.
Navigating the menus
Each menu has a list of options, which can be seen in detail on the menu
map on the below list.
When the handset is switched on and in standby mode:
1. Press to open the main menu.m
2. Then use buttons to scroll through the available options.u or d
3. Press to select an option. To return to the previous menu level,m
press . To exit the menu and return to standby, press .be
NOTE
If you do not press a button on the handset for 30 seconds the display will
automatically return to standby. It will also return to standby when the
handset is placed on the base or charger.
Menu map
Phonebook Ring tones Area code
View Key tone Flash time
Add new Dial mode Docking tone
Edit Auto clock Battery tone
Delete1Phone name Register
Delete all1Date & time Unregister
Phone setup Language Reset
Sounds Services
Ring volume Call list type
1Only available when an phonebook entry is already stored.
3. Using the phone
NOTE
Your handset will automatically time the duration of all external calls.
The call timer will display after the rst 10 seconds of your call. When the
call ends, the total duration of your talk time is shown for 3 seconds.
3.1 Switch the handset on / o
Press and hold to switch the handset on or o.e
3.2 Calls
3.2.1 Make a call
1. Press .t
2. Dialing a telephone number.
3.2.2 Pre-dial
1. Use the keypad to dial a number, if you make a mistake press b to
delete the last digit.
2. Press t to dial.
3.2.3 End a call
Press , or place the handset back on the base or charger.e
3.2.4 Answer a call
When you receive an external call, the phone rings and icon flashes
on the display.
1. Press t to answer the call.
3.3 Adjust the earpiece volume
During a call, press to increase or decrease the volume. There u or d
are 5 levels to choose from.
3.4 Mute
You can mute your handset so that you can talk to someone nearby
without your caller hearing.
1. During a call, press . The display shows M
Mute on
and your caller
cannot hear you.
2. Press again to resume your call.M
1. Getting started
IMPORTANT
Do not place your C100xLX in the bathroom or other humid areas.
Location
You need to place your C100xLX base within 6 feet of an electrical outlet
and a telephone wall socket to provide the power to supply the device
and to connect to telephone service.
Make sure it is at least 3 feet away from other electrical appliances
to avoid interference. Your C100xLX works by sending radio signals
between the handset and base. The strength of the signal depends on
where you place the base. Putting it as high as possible ensures the best
signal.
HANDSET RANGE
The unit has a range of up to 650 feet outdoors when there is a clear
line of sight between the base and handset. Any obstruction between
the base and handset will reduce the range signicantly. With the
base indoors and the handset either indoors or outdoors, the range will
normally be up to 100 feet. Thick concrete and stone walls can severely
aect the range.
SIGNAL STRENGTH
The icon on your handset indicates that you are within range of the
base. When out of range of the base, the icon disappears. If you are
on a call, you will hear a warning beep.
If you are on a call, the line will hang up if the handset moves out
of range of the base. Move back within range. The handset will
automatically re-connect to the base.
Setting up
IMPORTANT
Use only the power adapter and telephone line cord supplied with the
product.
This User Guide provides you with all the information you need to
get the most from your phone.
Before you make your rst call you will need to set up your phone.
Follow the simple instructions in ‘Getting Started’, on the next
few pages.
IMPORTANT
Only use the telephone line cord and power adapter supplied.
Got everything?
• C100xLX base & cordless handset
• 1 x rechargeable Ni-MH battery pack
• Power adapter for the base
• Telephone line cord
• User Guide
• Quick Start Guide
If you have purchased a C100xLX multiple pack you will also have
the following items:
• Cordless handset & charger
• Rechargeable Ni-MH battery pack
• Power adapter for the charger
• Telephone line cord
Welcome...
to your new Motorola C100xLX Digital Cordless Telephone!
•All handsets are completely cordless and easy to locate with paging system.
• Bright backlit display.
• Speakerphone for hands-free conversations.
• 50 Name and Number phonebook.
• Caller ID shows you who’s calling and shows the details of the last 20
callers in a Calls list.1
• Redial up to 10 of the last numbers called.
• Register up to 4 handsets to a single base.
• Make internal calls and transfer external calls between handsets.
• Choose from 10 dierent ringtones.
Please note that this equipment is not designed for making
emergency telephone calls when the power fails. Alternative
arrangements should be made for access to emergency services.
Need help?
If you have any problems setting up or your using your C100xLX
Digital Cordless Telephone, please contact Customer Service at
1-888-331-3383. Alternatively, you may nd the answer in the ‘Help’
section at the back of this guide.
1You must subscribe to your network provider’s Caller ID service for
this feature to work. A subscription fee may apply.
Please note that this equipment is not designed for making
emergency telephone calls when power fails. Alternative
arrangements should be made for access to emergency services.
Manufactured, distributed or sold by Binatone Technologies Ltd., oicial
licensee for this product. MOTOROLA and the Stylized M Logo are
trademarks or registered trademarks of Motorola Trademark Holdings,
LLC. and are used under license. All other trademarks are the property
of their respective owners. © 2014 Motorola Mobility LLC. All rights
reserved.
Version 15 (EN-US)
2. If you are charging the battery for the rst time, place the handset
on the charger to charge for at least 24 hours continuously.
3. When the handset is fully charged, icon will appear steady on
the display. The display will show
Handset
and handset number (e.g.
2) to indicate that it is registered to the base.
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery pack (AAA
2.4v 300mAh Ni-MH rechargeable battery) supplied with your C100xLX.
BATTERY LOW WARNING
If E icon flashes on the display and you hear a warning beep every 2
minutes during a call, you will need to recharge the handset before you
can resume use.
When charging, icon will scroll on the display. f
BATTERY PERFORMANCE
In ideal conditions, a fully charged battery should give up to 10 hours of
talk time or up to 200 hours standby time on a single charge.1
Note that new batteries do not reach their full capacity until it has been
put to normal use for several days.
To keep your batteries down at least one time per week will help prolong
battery life.
Running the batteries right down at least once a week will help them last
as long as possible.
The charge capacity of the rechargeable battery will reduce with time
as it wears out, giving the handset less talk / standby time. Eventually it
will need to be replaced.
Earpiece
Display
Phonebook / Scroll Up /
Volume down
Open the phonebook.
Scroll up through lists and
menus.
Increase the earpiece volume.
Menu / OK
Enter the main menu.
Select the option
displayed on screen.
Conrm menu option.
Talk / Flash
Make or answer a call.
Use flash (F) functions.
* / Intercom
Press and hold to make
an internal call.
Dial a *.
Hands-free
Activate and deactivate
hands-free during a call.
IMPORTANT
Hands-free activation can
suddenly increase the
volume in the earpiece to
a very high level. Make
sure the handset is not
too close to your ear.
Redial
In standby mode, press
to open the redial list.
Clear / Back
Delete characters on screen
when entering names and
numbers.
Go back to previous menu
level is displayed on the
screen.
Call list / Scroll Down /
Volume down
Press to enter the Calls list.
Scroll down through lists
and settings.
During a call, press to
decrease earpiece volume.
When the phone is ringing,
press to decrease the
handset ringer volume.
End call / Switch handset
on/o
End a call.
When in a menu, go back
to standby mode.
Press and hold to switch
handset o (when in
standby) or on.
Pause / # / Change case
Press and hold to enter a
pause (P) when pre-dialling
or storing numbers.
Dial a #.
When entering letters /
editing, press and hold to
change the case from Abc
to abc or ABC mode.
When viewing the Calls
List press to change the
CID format.
Microphone
Mute
Mute / unmute the
microphone during a
call.
Digital Cordless Telephone
Models: C1001LX, C1002LX, C1003LX and C1004LX
allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to
the requirement that the sum of the RENs of all the devices does not
exceed ve.
This equipment meets the applicable Industry Canada Terminal
Equipment & Technical Specications.
Placing the receiver slightly above the ear may result in better
performance for hearing aids with microphones positioned behind the
ear.
Specic Absorption Rate (SAR) information
SAR tests are conducted using standard operating positions accepted
by the FCC with the phone transmitting at its highest certied power
level in all tested frequency bands, although the SAR is determined at
the highest certied power level, the actual SAR level of the phone while
operating can be well below the maximum value, in general, the closer
you are to a wireless base station antenna, the lower the power output.
Before a new model phone is a available for sale to the public, it must be
tested and certied to the FCC that it does not exceed the exposure
limit established by the FCC, Tests for each phone are performed
in positions and locations (e.g. at the ear) as required by the FCC.
This handset has also been tested and meets the FCC RF exposure
guidelines. Use of other accessories may Non-compliance with the
above restrictions may result in violation of RF exposure guidelines.
what will disable alarm equipment, consult your telephone company or
a qualied installer.
If this equipment is malfunctioning, it must be unplugged from the
modular jack until the problem has been corrected. Repairs to this
telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined
under the Limited Warranty.
If this equipment is causing harm to the telephone network, the
telephone company may temporarily discontinue your telephone
service. The telephone company is required to notify you before
interrupting service. If advance notice is not practical, you will be
notied as soon as possible. You will be given the opportunity to correct
the problem and the telephone company is required to inform you of
your right to le a complaint with the FCC. Your telephone company
may make changes in its facilities, equipment, operation, or procedures
that could aect the proper functioning of this product. The telephone
company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is
hearing aid compatible.
If this product has memory dialing locations, you may choose to store
emergency telephone numbers (e.g., police, re, medical) in these
locations. If you do store or test emergency numbers, please:
• Remain on the line and briefly explain the reason for the call before
hanging up.
• Perform such activities in o-peak hours, such as early morning or
late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference, including interference
that may cause undesired operation.
The term “IC: “ before the certication/registration number only signies
that the Industry Canada technical specications were met.
The Ringer Equivalence Number (REN) for this terminal equipment
is 0.0B. The REN is an indication of the maximum number of devices
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Le present appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioelectrique subi, meme si le brouillage est susceptible
d’en compromettre le fonctionnement.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with
technical requirements adopted by the Administrative Council for
Terminal Attachments (ACTA). This Product Complies With 47CFR
PART 68.
The plug and jack used to connect this equipment to premises wiring
and the telephone network must comply with applicable Part 68 rules
and technical requirements adopted by ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. An RJ11
jack should normally be used for connecting to a single line and an RJ14
jack for two lines. See Installation Instructions in the User’s Guide.
The Ringer Equivalence Number (REN) is used to determine how many
devices you may connect to your telephone line and still have them ring
when you are called. The REN for this product is encoded as the 6th and
7th characters following the US: in the product identier (e.g., if ## is
03, the REN is 0.3). In most, but not all areas, the sum of all RENs should
be ve (5.0) or less. For more information, please contact your local
telephone company.
This equipment may not be used with Party Lines. If you have specially
wired alarm dialing equipment connected to your telephone line, ensure
the connection of this equipment
does not disable your alarm equipment. If you have questions about
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These requirements are
intended to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount
of radio frequency energy that can be safely absorbed by a user or
bystander according to the intended usage of the product. This product
has been tested and found to comply with the FCC criteria. Both the
Handset may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user’s body other
than the hands are maintained at a distance of approximately 20 cm (8
inches) or more.
than MOTOROLA, BINATONE or its authorized service centers, are
excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or
date tags that have been removed, altered or obliterated; (b) broken
seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d) nonconforming
or non-Motorola branded housings, or parts, are excluded from
coverage.
Communication Services. Defects, damages, or the failure of Products
or Accessories due to any communication service or signal you may
subscribe to or use with the Products or Accessories is excluded from
coverage.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
US and Canada: 1-888-331-3383
Email: motorola@encompass.com
You will receive instructions on how to ship the Products or Accessories
at your expense and risk, to a BINATONE Authorized Repair Center.
To obtain service, you must include: (a) the Product or Accessory; (b)
the original proof of purchase (receipt) which includes the date, place
and seller of the Product; (c) if a warranty card was included in your box,
a completed warranty card showing the serial number of the Product;
(d) a written description of the problem; and, most importantly; (e) your
address and telephone number.
These terms and conditions constitute the complete warranty
agreement between you and BINATONE. regarding the Products or
Accessories purchased by you, and supersede any prior agreement
or representations, including representations made in any literature
publications or promotional materials issued by BINATONE. or
representations made by any agent employee or sta of BINATONE, that
may have been made in connection with the said purchase.
Products Covered Length of Coverage
Consumer Products from the date of the products One (1) year
original purchase by the rst consumer
purchaser of the product.
Consumer Accessories Ninety (90) days from the date of the
accessories original purchase by the rst
consumer purchaser of the product.
Consumer Products and
Accessories that are
Repaired or Replaced
The balance of the original warranty
or for ninety (90) days from the date
returned to the consumer, whichever is
longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement
of parts due to normal wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of
their rated capacity and batteries that leak are covered by this Warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper
operation, storage, misuse or abuse, accident or neglect, such as
physical damage (cracks, scratches, etc.)
to the surface of the product resulting from misuse; (b) contact with
liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or
the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes or
subjecting the Product or Accessory to abnormal usage or conditions; or
(d) other acts which are not the fault of MOTOROLA or BINATONE., are
excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or certied
Products or Accessories or other peripheral equipment are excluded
from coverage. Unauthorized Service or Modication. Defects or
damages resulting from service, testing, adjustment, installation,
maintenance, alteration, or modication in any way by someone other
SAVE THESE INSTRUCTIONS
What will BINATONE do?
BINATONE or its authorized distributor at its option and within a
commercially reasonable time, will at no charge repair or replace any
Products or Accessories that does not
conform to this Warranty. We may use functionally equivalent
reconditioned/ refurbished/ pre-owned or new Products, Accessories
or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR
OR REPLACEMENT PROVIDED UNDER THIS EXPRESS LIMITED
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND
IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF
IMPLIED. IN NO EVENT SHALL MOTOROLA OR BINATONE BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE
PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE
OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR
ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion of incidental
or consequential damages, or limitation on the length of an implied
warranty, so the above limitations or exclusions may not apply to you.
This Warranty gives you specic legal rights, and you may also have
other rights that vary from one jurisdiction to another.
10. To avoid interference to nearby appliances, do not place the base of
the phone on or near a TV, microwave oven, or VCR.
CAUTION
To maintain compliance with the FCC’s RF exposure guidelines, place
the base unit at least 8 inches from nearby persons.
Battery Safety Instructions
• Do not burn, disassemble, mutilate, or puncture the battery. The
battery contains toxic materials that could be released, resulting in
injury.
Consumer Products and Accessories
Limited Warranty (“Warranty”)
Thank you for purchasing this Motorola branded product manufactured
under license by Binatone Electronics International LTD (“BINATONE”).
What Does this Warranty Cover?
Subject to the exclusions contained below, BINATONE warrants that
this Motorola branded product (“Product”) or certied accessory
(“Accessory”) sold for use with this product that it manufactured to be
free from defects in materials and workmanship under normal consumer
usage for the period outlined below. This Warranty is your exclusive
warranty and is not transferable.
Who is covered?
This Warranty extends only to the rst consumer purchaser, and is not
transferable.
CAUTION
To reduce the risk of re, use only No. 26 AWG or larger UL Listed or CSA
Certied Telecommunication Line Cord.
Unplug this cordless phone immediately from an
outlet if:
• The power cord or plug is damaged or frayed.
• Liquid has been spilled on the product.
• The product has been exposed to rain or water. Do not retrieve
the handset or base until after you have unplugged the power and
phone from the wall. Then retrieve the unit by the unplugged cords.
• The product has been dropped or the cabinet has been damaged.
• The product exhibits a distinct change in performance.
Installation Guidelines
1. Read all instructions and save them for future reference.
2. Follow all warnings and instructions marked on the product.
3. Do not install this product near a bath tub, sink, or shower.
4. Operate this phone using only the power source that is indicated
on the marking label. If you are unsure of the power supply to your
home, consult with your dealer or local power company.
5. Do not place this product on an unstable cart, stand, or table. This
product may fall, causing serious damage to the product.
6. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in
damage and will often require extensive work to restore the product
to normal operation.
7. Clean this product with a soft, damp cloth. Do not use chemicals or
cleaning agents to clean this phone.
8. Use only the power supply that came with this unit. Using other
power supplies may damage the unit.
9. Because this phone operates on electricity, you should have at least
one phone in your home that operates without electricity in case of
a power outage.
9. General information
If your product is not working properly...
1. Read this User’s Guide.
2. Visit our website: www.motorola.com
3. Contact Customer Service in the US and Canada at
1-888-331-3383
Email: motorola@encompass.com
Important safety instructions
Follow these safety precautions when using your phone to reduce the
risk of re, electric shock, and injury to persons or property:
1. Keep all vents and openings of the phone unblocked.
Do not set the phone on a heating register or over a radiator. Ensure
that proper ventilation is provided at the installation site.
2. Do not use while wet or while standing in water.
3. Do not use this product near water (for example, near a bath tub,
kitchen sink, or swimming pool).
4. Do not allow anything to rest on the power cord. Place the power
cord so that it will not be walked on.
5. Never insert objects of any kind into the product vents as that may
result in re or electric shock.
6. Unplug this product from the electrical outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
7. Do not disassemble this product. If service or repair work is required,
contact the customer service helpline found in this User’s Guide.
8. Do not overload wall outlets and extension cords.
9. Avoid using during an electrical storm. Use a surge protector to
protect the equipment.
10. Do not use this phone to report a gas leak, especially if you are in the
vicinity of the gas line.
No ring tone
• The ring tone is deactivated.
• Increase the volume.
Caller ID service does not work
• Check your subscription with your network operator.
A phonebook entry cannot be stored
• The phonebook is full. Delete an entry to free memory.
No display
• Try recharging or replacing the batteries.
• Try disconnecting and connecting the base power supply.
• If the LED is not lit up, then try disconnecting and connecting the
base power supply.
Unable to register another handset
• Maximum number of 4 handsets has been reached.
• The display shows
Searching
. You must unregister a handset in order
to register a new one.
Noise interference on your radio or television
• Your base or charger may be too close. Move it as far away as
possible.
7.2.4 Delete an entry
1. to open the Calls list.Press d
2. Scroll u or d to the entry you want.
3. Press , the display shows m
View
.
4. Scroll d to
Delete
and press . The display shows m
Conrm?
.
5. Press to conrm or mb to cancel.
7.2.5 Delete the entire Calls list
1. to open the Calls list.Press d
2. Press , the display shows m
View
.
3. Scroll d to
Delete all
and press . The display shows m
Conrm?
.
4. Press to conrm or mb to cancel.
8. Help
The icon is not scrolling during charge
• Bad battery contact – move the handset slightly.
• Dirty contact – Clean the battery contact with a cloth moistened
with alcohol.
• Battery is full – no need to charge.
No dialling tone
• No power – check the connections. Reset the phone: unplug and
plug back in the electrical outlet.
• Batteries are empty – charge the batteries for at least 24 hours.
• You are too far from the base – move closer to the base.
• Wrong line cable – use the line cable provided.
Poor audio quality
• The base is too close to electrical appliances, reinforced concrete
walls or metal doorframes – move the base at least 3 feet away away
from any electrical appliances.
The icon is blinking or has disappeared
• Handset is not registered to the base – register the handset to the base.
• You are too far from the base – move closer to the base.
7.2.1 View the Calls list
1. to open the Calls list. If there are no calls in the list, the Press d
display shows
List empty
.
• The most recent number or name if stored in the phonebook
is displayed.
2. Press u or d to scroll through the list.
• If the call was answered, icon is displayed as you scroll to the
entry. If the call was unanswered, icon is displayed as you
scroll to the entry.
• If the telephone number is longer than 16 digits, icon is u
displayed. Press to see the remaining digits.b
• Press to access the option to store the entry in your m
phonebook.
• Press m twice to see the time and date of the call.
3. When viewing a calls list number press # to toggle the Calls List
between dierent formats, e.g. YYY-YYYY, AAA-YYY-YYYY or
1-AAA-YYY-YYYY.
7.2.2 Dial a number in the Calls list
1. to open the Calls list.Press d
2. Scroll u or d to the entry you want.
3. Press to dial the displayed entry.t
7.2.3 Save a number from a Calls list number to the phonebook
1. to open the Calls list.Press d
2. Scroll u or d to the entry you want.
3. Press , the display shows m
View
.
4. Scroll d to
Save number
and press . m
5. The display shows
Enter name
.
6. Enter the name and press . The number is displayed.m
7. Edit the number if necessary, then press . The number is stored.m
7. Caller ID and the Calls list
IMPORTANT
To use Caller ID, you must rst subscribe to the service from your network
provider. A subscription fee may be applicable.
To ensure that the caller’s name is displayed, make sure you have stored
the full telephone number, including the area code in the phonebook.
If the call is blocked,
Private
will be displayed.
If the number is unavailable,
Unknown
will be displayed.
If the call is from the operator,
Operator
will be displayed.
If the call is from a payphone,
Payphone
will be displayed.
If the call is from a ringback request,
Ringback
will be displayed.
7.1 Caller ID
If you have subscribed to a Caller ID Service, you will be able to see
your caller’s number on your handset (provided it is not withheld)
prior to answering the call. The display can show the rst 16 digits or 14
characters of the phone numbers.
If your caller’s name and number are stored in the phonebook and a
number match is found, you will see the caller’s name on the display as
well.
7.2 Calls list
The Calls list stores details of your last 50 received calls, including the
phone number, date and time of call.
The Calls list also alerts you when you have unanswered calls.
The caller’s details are stored in the Calls list whether or not you have
answered the call. The list is shared by all handsets registered to the base.
When the list is full, and a new call is received, the oldest entry will be
deleted automatically.
When you have missed call(s) (incoming calls that you haven’t answered)
the display will show
X Missed call(s)
and the icon will flash on all handsets
registered to the base. Press to see the callers details.m
3. When the display shows
PIN
, enter the base PIN and press . m
When the handset registers with the base, it is assigned a handset
number.
6.6.2 Un-register a handset
Use one handset to delete another. You cannot delete the handset that
you are using.
1. Press , scroll md to
Services
and press .m
2. Scroll d to
Unregister
and press .m
3. Enter the 4 digit master PIN and press . m
Display shows the rst registered handset number.
4. Scroll to select the handset you want to delete and press u or d
m.
Unregistered
is displayed on the handset screen.
6.7 Restore default settings
You can restore your C100xLX to its default (original) settings.
All the handsets that are registered to the base will be retained.
IMPORTANT
Resetting your phone to its default setting will delete all entries in the
Phonebook and Calls list. All handset and base settings will also be reset.
1. Press , scroll md to
Services
and press .m
2. Scroll d to
Reset
and press .m
3.
Conrm?
is displayed. Press .m
6.8 Default settings
Handset name HANDSET Phonebook Empty
Low battery beeps ON Calls list Empty
Docking tone ON Redial list Empty
Key tone ON PIN code 0000
Ringer tones 1 Dial mode Tone
Ringer volume 3 Flash mode Long (600 ms)
Earpiece volume 1 Keypad lock OFF
6.4 Dial mode
The default C100xLX dialling mode is suitable for your country and
network operator. It is unlikely that you should need to change this
setting unless advised to do so.
1. Press , scroll md to
Services
and press .m
2. Scroll d to
Dial mode
and press .m
3. Press to select u or d
Tone
or
Pulse
and press m to conrm.
6.5 Switch Auto clock on / o
If you have subscribed to a Caller ID Service, the date and time will be
set on all your handsets whenever a call is received. This feature can be
set to On or O.
1. Press m, scroll to
Services
and press .m
2. Scroll d to
Auto clock
and press .m
3. Scroll d to
On
or
O
then press to conrm.m
6.6 Registration
Up to 4 handsets can be registered to one base station. Additional
handsets must be registered to the base before you can use them.
• The instructions described below apply specically to your C100xLX
handset. If you wish to register another manufacturer’s handset, the
instructions may vary. In this case, please refer to the manufacturer
of the additional handset.
• The Master PIN is required before you can register or unregister
handsets. The PIN is 0000.
6.6.1 Register a handset
At the base:
1. Press and hold the on the base until the base beeps. You have p
120 seconds in which to register a handset.
At the handset:
1. If the handset is not already registered to a base, press .m
2. Or if the handset is already registered to a base, press scroll md
to
Services
and press . Scroll md to
Register
and press .m
6. Services
6.1 Call List type
You can set the Call list to show All calls or Missed calls only. If All calls
is selected, press key in idle and you can view all calls lists. If Missed d
calls is selected, press key in idle and you can view missed call only.d
1. Press , scroll md to
Services
and press . m
2. The display shows
Call list type
, press .m
3. Scroll u or d to select
All calls
or
Missed calls
and press m to
conrm.
6.2 Area code
You can set your local area code into the phone. When a number from
that area code calls only the local number will be displayed and stored.
The area code can be up to 3 digits long.
Note: If the area code is stored in the phone it will not display the full
phone number.
1. Press , scroll md to
Services
and press .m
2. Scroll d to
Area code
is displayed. Press .m
3. Using the keypad enter the area code and press m to conrm.
6.3 Flash time
Depending on your country and network operator, your C100xLX has
the flash time set as 600 ms (Long). It is unlikely that you need to change
this setting unless advised to do so.
1. Press , scroll md to
Services
and press .m
2. Scroll d to
Flash time
and press .m
3. Press u or d to select
Short
,
Medium
or
Long
and press m to
conrm.
5.1.5 Battery tones
When you the battery is running low you will hear a warning beep. You
can switch this beep on or o.
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Press . Scroll md to
Battery tone
.
4. Press , mu or d to select
On
or
O
and press m to conrm.
5.2 Handset name
Personalize your handset, with a name or location for example Peter or
Bedroom. Maximum 12 characters.
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Scroll d to
Phone name
and press . m
4. Enter the new handset name and press m to conrm.
Delete the current name by pressing .b
5.3 Date & time
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Scroll d to
Date & time
and press . m
4. Enter the date using the keypad (e.g. 08--12--14 for 12th of August
2014) and press m to conrm.
5. Enter the time using the 12 hour format
hh:mm
, e.g. 02:45 for 2:45.
6. Scroll u or d to select
am
or
pm
and press m to conrm.
5.4 Language
1. Press , scroll md to
Phone setup.
2. Press . The display shows m
Sounds
.
3. Scroll d to
Language
and press . m
4. Scroll to select the required language and press u or dm to
conrm.

Produktspezifikationen

Marke: Motorola
Kategorie: Schnurlose DECT-Telefone
Modell: C1002LX

Brauchst du Hilfe?

Wenn Sie Hilfe mit Motorola C1002LX benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Schnurlose DECT-Telefone Motorola

Motorola

Motorola CD4012 Bedienungsanleitung

5 Oktober 2024
Motorola

Motorola CD401-B Bedienungsanleitung

25 August 2024
Motorola

Motorola CD501-B Bedienungsanleitung

23 August 2024
Motorola

Motorola CD401-HS Bedienungsanleitung

19 August 2024
Motorola

Motorola AXH Bedienungsanleitung

12 August 2024
Motorola

Motorola L502BT Bedienungsanleitung

8 August 2024
Motorola

Motorola CD501-C Bedienungsanleitung

7 August 2024
Motorola

Motorola CD5011 Bedienungsanleitung

3 August 2024
Motorola

Motorola L706C Bedienungsanleitung

31 Juli 2024
Motorola

Motorola CD4014 Bedienungsanleitung

19 Juli 2024

Bedienungsanleitung Schnurlose DECT-Telefone

Neueste Bedienungsanleitung für -Kategorien-

Tiptel

Tiptel 205 PLUS Bedienungsanleitung

5 Oktober 2024
KPN

KPN Atlanta 100 HS+BS Bedienungsanleitung

5 Oktober 2024
Tiptel

Tiptel 240 Bedienungsanleitung

18 September 2024
Premier

Premier Maxima 500 Bedienungsanleitung

16 September 2024
Premier

Premier Moonlight 200 Bedienungsanleitung

16 September 2024
Alcatel

Alcatel F380-S Draadloze DECT telefoons Bedienungsanleitung

10 September 2024
Alcatel

Alcatel Origin Draadloze DECT telefoons Bedienungsanleitung

10 September 2024
Alcatel

Alcatel F530 Draadloze DECT telefoons Bedienungsanleitung

9 September 2024
Alcatel

Alcatel Vision Draadloze DECT telefoons Bedienungsanleitung

9 September 2024
Alcatel

Alcatel F330 Draadloze DECT telefoons Bedienungsanleitung

8 September 2024