Milwaukee 0370-20 Bedienungsanleitung
Milwaukee
Bohrmaschine
0370-20
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 0370-20 (15 Seiten) in der Kategorie Bohrmaschine. Dieser Bedienungsanleitung war für 43 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/15
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
Cat. No.
No de cat.
Cat. No.
0370-20
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
HEAVY-DUTY CLOSE QUARTER DRILLS
EXTRA ROBUSTES PERCEUSES COUDÉES
MINITALADRO ANGULAR HEAVY-DUTY
2 3
WORK AREA SAFETY
ELECTRICAL SAFETY
PERSONAL SAFETY
WARNING
READ ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in electric shock, fi re and/or
serious injury. The term "power tool" in all of the warnings listed below refers to your
mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
GENERAL SAFETY RULES — FOR ALL POWER TOOLS
1. Keep work area clean and well lit.
Cluttered or dark areas invite acci-
dents.
2. Do not operate power tools in ex-
plosive atmospheres, such as in the
presence of fl ammable liquids, gases,
or dust. Power tools create sparks which
may ignite the dust or fumes.
3. Keep children and bystanders away
while operating a power tool. Distrac-
tions can cause you to lose control.
4. Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets
will reduce risk of electric shock.
5. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
6. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
7. Do not abuse the cord. Never use the
cord for carrying, pulling, or unplug-
ging the power tool. Keep cord away
from heat, oil, sharp edges, or mov-
ing parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool out-
doors, use an extension cord suitable
for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of elec-
tric shock.
9. Stay alert, watch what you are do-
ing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the infl uence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result
in serious personal injury.
10. Use safety equipment. Always wear
eye protection. Safety equipment such
as dust mask, non-skid safety shoes,
hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
11. Avoid accidental starting. Ensure the
switch is in the off-position before plug-
ging in. Carrying tools with your fi nger on
the switch or plugging in power tools that
have the switch on invites accidents.
12. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotat-
ing part of the power tool may result in
personal injury.
13. Do not overreach. Keep proper foot-
ing and balance at all times. This
enables better control of the power tool
in unexpected situations.
14. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery, or long
hair can be caught in moving parts.
15. If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of these de-
vices can reduce dust-related hazards.
POWER TOOL USE AND CARE
16. Do not force the power tool. Use the
correct power tool for your applica-
tion. The correct power tool will do the
job better and safer at the rate for which
it was designed.
17. Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
18. Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preven-
tive safety measures reduce the risk of
starting the tool accidentally.
19. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tools or
these instructions to operate power
tools. Power tools are dangerous in the
hands of untrained users.
20. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool's operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
21. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
22. Use the power tool, accessories and
tool bits etc., in accordance with
these instructions and in the manner
intended for the particular type of
power tool, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
SERVICE
23. Have your power tool serviced by a
qualifi ed repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
SPECIFIC SAFETY RULES
1. Hold power tools by insulated grip-
ping surfaces when performing an
operation where the cutting tool may
contact hidden wiring or its own cord.
Contact with a "live" wire will make ex-
posed metal parts of the tool "live" and
shock the operator.
2. Wear ear protectors with impact
drills. Exposure to noise can cause
hearing loss.
3. Keep hands away from all cutting
edges and moving parts.
4. Maintain labels and nameplates.
These carry important information.
If unreadable or missing, contact a
MILWAUKEE service facility for a free
replacement.
5. WARNING! Some dust created by
power sanding, sawing, grinding, drill-
ing, and other construction activities
contains chemicals known to cause
cancer, birth defects or other reproduc-
tive harm. Some examples of these
chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this
type of work. To reduce your exposure
to these chemicals: work in a well ven-
tilated area, and work with approved
safety equipment, such as those dust
masks that are specially designed to
fi lter out microscopic particles.
4 5
erly grounded outlet (See Figure A). If the tool
should electrically malfunction or break down,
grounding provides a low resistance path to
carry electricity away from the user, reducing
the risk of electric shock.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected to
the tool's grounding system and must never be
attached to an electrically “live” terminal.
Your tool must be plugged into an appropri-
ate outlet, properly installed and grounded in
accordance with all codes and ordinances.
The plug and outlet should look like those in
Figure A.
Double Insulated Tools:
Tools with Two Prong Plugs
Grounded Tools:
Tools with Three Prong Plugs
Fig. B Fig. C
Fig. A
Improperly connecting the grounding
wire can result in the risk of electric
shock. Check with a qualifi ed electri-
cian if you are in doubt as to whether
the outlet is properly grounded. Do not
modify the plug provided with the tool.
Never remove the grounding prong
from the plug. Do not use the tool if the
cord or plug is damaged. If damaged,
have it repaired by a MILWAUKEE ser-
vice facility before use. If the plug will
not fi t the outlet, have a proper outlet
installed by a qualifi ed electrician.
GROUNDING
WARNING
FUNCTIONAL DESCRIPTION
1. Chuck
2. Paddle switch
3. Forward/Reverse switch
4. Cord
2
1
3
4
No Load
RPM
0 - 1300
Volts
AC
120
Catalog
Number
0370-20
Specifi cations
Amps
3.5
Twist Drill
Capacity
in Steel
3/8"
AmperesDouble Insulated
Underwriters
Laboratories, Inc. Volts Alternating Current
No Load Revolutions
per Minute (RPM)
Symbology
Mexican Approvals
Marking
Tools marked “Ground-
ing Required” have a
three wire cord and
three prong grounding
plug. The plug must be
connected to a prop-
Tools marked “Double
Insulated” do not re-
quire grounding. They
have a special double
insulation system which
satisfi es OSHA require-
ments and complies
with the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association and the National Electrical
Code. Double Insulated tools may be used
in either of the 120 volt outlets shown in
Figures B and C.
Grounded tools require a three wire exten-
sion cord. Double insulated tools can use
either a two or three wire extension cord.
As the distance from the supply outlet
increases, you must use a heavier gauge
extension cord. Using extension cords with
inadequately sized wire causes a serious
drop in voltage, resulting in loss of power
and possible tool damage. Refer to the table
shown to determine the required minimum
wire size.
The smaller the gauge number of the wire,
the greater the capacity of the cord. For ex-
ample, a 14 gauge cord can carry a higher
current than a 16 gauge cord. When using
more than one extension cord to make up
the total length, be sure each cord contains
at least the minimum wire size required. If
you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord out-
doors, be sure it is marked with the suffi x
“W-A” (“W” in Canada) to indicate that it
is acceptable for outdoor use.
• Be sure your extension cord is prop-
erly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by a
qualifi ed person before using it.
• Protect your extension cords from sharp
objects, excessive heat and
damp or wet areas.
EXTENSION CORDS
READ AND SAVE ALL
INSTRUCTIONS FOR
FUTURE USE.
Recommended Minimum Wire Gauge
for Extension Cords*
Extension Cord Length
* Based on limiting the line voltage drop to
fi ve volts at 150% of the rated amperes.
Nameplate
Amperes
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
25'
18
18
18
18
16
14
12
75'
18
18
16
14
12
10
100'
18
16
14
12
10
150'
16
14
12
12
50'
18
18
18
16
14
12
10
Produktspezifikationen
| Marke: | Milwaukee |
| Kategorie: | Bohrmaschine |
| Modell: | 0370-20 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee 0370-20 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Bohrmaschine Milwaukee
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
Bedienungsanleitung Bohrmaschine
- Bohrmaschine Panasonic
- Bohrmaschine Cotech
- Bohrmaschine Makita
- Bohrmaschine Bosch
- Bohrmaschine Flex
- Bohrmaschine Parkside
- Bohrmaschine Vonroc
- Bohrmaschine AEG
- Bohrmaschine Velleman
- Bohrmaschine IKEA
- Bohrmaschine Black And Decker
- Bohrmaschine Cocraft
- Bohrmaschine FERM
- Bohrmaschine Ryobi
- Bohrmaschine Skil
- Bohrmaschine Trotec
- Bohrmaschine Baier
- Bohrmaschine Carat
- Bohrmaschine Hilti
- Bohrmaschine Sparky
- Bohrmaschine DeWalt
- Bohrmaschine Einhell
- Bohrmaschine Elu
- Bohrmaschine Festool
- Bohrmaschine Worx
- Bohrmaschine Tacklife
- Bohrmaschine Hikoki
- Bohrmaschine Hitachi
- Bohrmaschine Hazet
- Bohrmaschine Kinzo
- Bohrmaschine Kress
- Bohrmaschine Metabo
- Bohrmaschine Stanley
- Bohrmaschine Güde
- Bohrmaschine Power Craft
- Bohrmaschine Workzone
- Bohrmaschine Meec Tools
- Bohrmaschine Dremel
- Bohrmaschine Fieldmann
- Bohrmaschine Proxxon
- Bohrmaschine Berner
- Bohrmaschine Westfalia
- Bohrmaschine Stihl
- Bohrmaschine Dedra
- Bohrmaschine DURO
- Bohrmaschine Graphite
- Bohrmaschine Pattfield
- Bohrmaschine Silverline
- Bohrmaschine Holzmann
- Bohrmaschine Sthor
- Bohrmaschine Herkules
- Bohrmaschine Robust
- Bohrmaschine Zipper
- Bohrmaschine Yato
- Bohrmaschine Baumr-AG
- Bohrmaschine Genesis
- Bohrmaschine Delta
- Bohrmaschine Batavia
- Bohrmaschine Bavaria
- Bohrmaschine Narex
- Bohrmaschine Toolcraft
- Bohrmaschine Fein
- Bohrmaschine Gardena
- Bohrmaschine Craftsman
- Bohrmaschine Defort
- Bohrmaschine Powerplus
- Bohrmaschine Alpha Tools
- Bohrmaschine Ozito
- Bohrmaschine Sun Joe
- Bohrmaschine Ridgid
- Bohrmaschine Porter-Cable
- Bohrmaschine Guede
- Bohrmaschine Felisatti
- Bohrmaschine Gamma
- Bohrmaschine Global
- Bohrmaschine Lux Tools
- Bohrmaschine Tanaka
- Bohrmaschine Wolfcraft
- Bohrmaschine Meister Craft
- Bohrmaschine Truper
- Bohrmaschine Kreg
- Bohrmaschine Einhell Bavaria
- Bohrmaschine Prowork
- Bohrmaschine Bullcraft
- Bohrmaschine Tryton
- Bohrmaschine Ergotools Pattfield
- Bohrmaschine THUN
- Bohrmaschine Bavaria By Einhell
Neueste Bedienungsanleitung für -Kategorien-
11 August 2024
9 August 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
18 Juni 2024