Miele TWF720 WP Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Miele TWF720 WP (4 Seiten) in der Kategorie Trockner. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Using for the first time Operation Drying Fragrance flacon
M.-Nr. 11 495 23000
3. Loading the tumble dryer
ĺOpen the door.
ĺUnfold the laundry and load
loosely into the drum.
Do not overload the drum.
Overloading can cause
unnecessary wear and tear of
the laundry,
give a disappointing
drying result and cause more
creasing.
If you are not using a fragrance
flacon: the tabs must be pushed
down completely (see arrows) to
ensure both sockets are closed.
ĺShut the door with a gentle
swing.
When closing the door, make
sure that laundry does not get
trapped in the door opening.
FragranceDos – the dryer has two
positions for inserting a fragrance flacon.
Use one or both whenever you want to
add a pleasant fragrance to your laundry.
Close the unused socket.
Before using a fragrance flacon, please
read "Warning and Safety instructions
- Using a fragrance flacon (optional
accessory)" and "Fragrance flacon" in
the operating instructions.
Inserting a fragrance flacon
1. 2.
3. 4.
Markers and must line up with
each other.
5. 6.
ĺTurn the outer ring clockwise a little.
Markers und must line up with
each other.
Before drying
ĺTurn the outer
ring clockwise
a little.
The further you open the flacon, the
more intense the fragrance.
After drying
To avoid the fragrance escaping
needlessly:
ĺTurn the outer
ring anti-clock-
wise until
marker is in
position .
When not in use, you can store the
fragrance flacon in its original
packaging.
Before cleaning the fluff filters
ĺRemove the
fragrance
flacon.
ĺOnly store the
fragrance
flacon in its
original
packaging.
Never lay the fragrance flacon down.
Otherwise, the fragrance will leak out.
Changing the programme sequence
TWF 720 WP en - AU, NZ
1 Condensed water container
– Empty after every drying programme
2 Door
3 Control panel
4 Access panel for the heat exchanger and plinth filter
– Do not open during drying
5 Cool air intake grille
– Do not obstruct with a laundry basket or other objects
OPERATION
DRYING
CHANGING THE PROGRAMME SEQUENCE
3. Selecting a programme and starting it
Selecting a programme
ĺTurn the programme selector.
–The dryer is switched on.
–A drying level may light up and durations will appear in
the time display.
Programmes with drying levels
–Cottons, Minimum iron, Delicates, Shirts, Express,
Denim, Bed linen, Pre-ironing
ĺTouch the sensor for the drying
level you want. It then lights up
brightly.
Any drying level can be selected
for the and Cottons, Express,
Bed linen programmes. A lim-
ited range is available with the
other programmes.
Other programmes and timed drying programmes
–Cottons Woollens handcare, Proofing ,
The drying level / duration is preset by the dryer
automatically and cannot be altered.
– Warm air
ĺTouch the sensor repeatedly
until the required programme
duration appears in the display.
You can set the duration in
10-minute increments from
0:20 minutes up to 2:00 hours.
ĺYou can reduce the duration with the sensor.
1. Notes on correct laundry care
ɒDamage due to foreign objects.
Foreign objects left in the laundry can melt, burn, or
explode.
Ensure that any foreign objects (e.g. detergent
dispensing balls, lighters, etc.) have been removed from
the laundry.
ĺSort the laundry according to the type of fibre and
weave, size, garment care label symbol and the drying
level required.
ĺUntangle the laundry.
ĺCheck seams and stitching to ensure that padding and
linings are intact.
ĺFasten duvet covers and pillow cases to prevent small
items from being rolled up inside them.
ĺFasten hooks and eyes.
ĺTie together textile belts and apron ties.
ĺSew in or remove loosened underwiring from bras.
Adding or removing laundry
You have forgotten an item of laundry, but
the programme has already started.
ĺTouch the sensor.Start/Add laundry
Add* will light up in the time display.
ĺOpen the door.
ĺAdd or remove laundry.
ĺClose the door.
ĺTouch the sensor.Start/Add laundry
The programme will start.
* Exceptions:
In some cases, e.g. during the cooling
phase or in the programme, you Proofing
cannot add laundry.
–In these cases will not light up.Add
Cancelling or changing the current
programme
It is no longer possible to change the
selected programme. This prevents the
appliance being operated unintentionally,
e.g. by children.
If you adjust the programme selector,
will light up in the time display.
goes out when you select the original
programme again.
ĺTurn the programme selector to the
position.
The programme is cancelled.
ĺSelect a new programme.
ĺTouch the sensor.Start/Add laundry
Select (if required).Gentle tumble
Delicate fabrics (with the symbol on the
care label, e.g. acrylic garments) are dried
at a lower temperature with a longer
programme duration.
ĺTouch the sensor. It then Gentle tumble
lights up brightly.
Selecting Delay start (if required)
With Delay start you can delay the start of
the programme by up to a maximum of
24hours.
Delay start cannot be used with the Warm
air programme.
ĺTouch the .
It then lights up
brightly.
ĺTouch the or sensors repeatedly
until the required Delay start time appears
in the display.
Starting a programme
ĺTouch the flashing Start/Add laundry
sensor. It will light up.
Energy saving:
After 10 minutes the indicators dim and
the sensor starts Start/Add laundry
flashing.
ĺTouch the sensor to Start/Add laundry
switch the indicators on again (this does
not have any effect on a running
programme).
4. Removing the laundry at the
end of the programme
End of programme: lights up in the
time display and the Start/Add laundry
sensor goes out.
–Energy saving: After 10 minutes the
indicators dim and the Start/Add laundry
sensor starts flashing.
–The dryer will switch off automatically
15minutes after the end of the
Anti-crease phase (with programmes
without an Anti-crease phase it will switch
off 15minutes after the end of the
programme).
ɒDo not open the door before the end
of the programme.
ĺOpen the door.
ĺRemove the laundry.
ɒCheck that all items have been
removed from the drum. If items are left
in the dryer, they could be damaged by
overdrying when the dryer is used the
next time.
If the dryer is switched on at the mains and
the door is opened, the drum lighting will
come on. It will go out after a few minutes
to save energy.
ĺTurn the programme selector to .
ĺClean the fluff filters.
ĺShut the door with a gentle swing.
ĺEmpty the condensed water container.Adding laundry
You can add laundry.
ĺFollow the instructions in "Changing the
programme sequence".
Energy saving tips
To avoid unnecessarily long drying times
and high consumption of energy:
–Spin the laundry at the maximum spin
speed in the washing machine.
Clean the fluff filters in the door and
in the door opening after every drying
cycle.
–Load according to the optimum
amount of laundry recommended for
the programme being used. This will
mean that the energy consumption for
the amount of laundry is at its most
economical.
–Make sure the room temperature is not
too high.
If there are other heat producing
appliances in the room in which the
tumble dryer is located, make sure the
room is well-ventilated and switch the
other appliances off, if possible.
1 Control panel
The , , and sensors react to 2 4 6 7
fingertip contact.
Selection is possible as long as the
respective sensor is illuminated.
–If a sensor is brightly lit, this means:
currently selected
–If a sensor is dimly lit, this means:
selection possible
2 Sensors for the drying levels
After selecting a drying level programme
with the programme selector: touch one
of the sensors to select a drying level.
3 Indicator lights
– light up if necessary:
see "Problem solving guide".
– Perfect Dry:
The Perfect Dry system measures the
residual moisture present in the
laundry in programmes with
selectable
drying levels and provides a more
precise drying result.
After starting the programme, this
message...
...will flash until the programme
duration has been determined, and
then go out.
...will light up when the selected
drying level is reached near the end of
the programme.
...will remain dark with the
following programmes: Woollens
handcare, Warm air.
4 Gentle tumble sensor
For drying temperature-sensitive textiles
with the symbol.
5 Time display
The remaining programme duration will
be displayed in hours and minutes.
6 Sensors
–After touching the sensor, a later
start time for the programme (Delay
start) can be selected.
–The and sensors are used for
selecting the duration of the Delay
start period or the duration of the
Warm air programme.
7 Start/Add laundry sensor
Touching the sensor Start/Add laundry
starts the selected programme. The
current programme can be interrupted to
add laundry. The sensor flashes slowly
as soon as it is possible for a
programme to be started and then lights
up constantly after the programme has
started.
8 Optical interface
For service technicians.
9 Programme selector
The programme selector can be turned
clockwise or anti-clockwise.
The dryer is switched on by selecting a
programme, and switched off by turning
the programme selector to the
position.
ɒBefore using the tumble dryer for
the first time, ensure that it is correctly
installed and connected.
Please read the separate operating
instructions supplied with the appliance.
ɒDamage caused by switching the
appliance on too soon.
This can damage the heat pump.
After setting up the tumble dryer, wait for
at least one hour before starting a drying
programme.
Emptying the condensed water
container
Empty the condensed water container
after every drying programme.
The indicator will light up when the
maximum level in the condensed water
container is reached.
To switch the indicator light off: Open
and close the door while the dryer is
switched on.
Damage to the door and fascia panel.
The door and the fascia panel can be
damaged when removing the condensed
water container.
Always close the door completely.
ĺPull out the
condensed water
container.
ĺTo prevent water running out, keep it in a
horizontal position when carrying it. Hold
it at the front and at the back.
ĺEmpty the con-
densed water
container.
ĺReplace the
container in the
dryer.
Do not drink condensed water. It can
cause health problems in people and
animals.
en - AU, NZ M.-Nr. 11 495 230
Quick Start Guide
Heat pump tumble dryer
These short instructions are not a substitute for the operating instructions supplied with
the appliance. Please read the operating instructions supplied with your tumble dryer
before using it for the first time.
Take note of the Warning and Safety instructions, as well as the full descriptions on how to
use your appliance.
Cleaning and care Problem solving guide
Fluff filters
Removing visible fluff
Clean the fluff filters in the door opening
after every drying cycle.
Remove the fragrance flacon (if fitted).
ĺPull the upper
fluff filter forwards
to remove it.
ĺUse your fin-
gers or a vac-
uum cleaner to
remove the fluff
from the surface
of the filter.
ĺPush the upper fluff filter back in until it
clicks into position.
ĺClose the door.
Cleaning the fluff filters and air flow
openings thoroughly
If the drying duration has become longer
or the surface of the filters is visibly
compacted with fluff, you should carry out
the following cleaning procedure.
ĺPull the upper fluff filter forward to remove
it.
ĺTurn the yellow
dial on the lower
fluff filter in the
direction of the
arrow (until you
hear it click).
ĺHold the dial and
pull the fluff fil-
ter forwards to
remove it.
ĺUse a vacuum
cleaner with a
long crevice noz-
zle attached to
remove any visi-
ble fluff from the
upper air flow
openings.
ĺFlush the fluff filters through with warm
running water.
ĺShake the fluff filters thoroughly and then
dry them carefully.
Ensure the filters are dry before
replacing them. Wet filters could cause
operational faults.
ĺRefit all of the fluff filters and close the
door.
CLEANING AND CARE
PROBLEM SOLVING GUIDE
Programme overview
PROGRAMME CHART
Garment care label symbols
Drying
Normal ⁄ higher temperature
Reduced temperature: select Gentle
tumble (for delicate fabrics).
Do not tumble dry
Ironing
very hot
hot
warm
Do not iron
Tips on drying
–Always observe the maximum recommended loads given in the
Programme chart.
Overloading can cause unnecessary wear and tear to the
laundry. It can give a disappointing drying result and cause more
creasing.
–Do not load the drum with items that are still soaking wet. Make
sure your laundry is spun at the maximum spin speed in the
washing machine before drying.
–Minimum iron fabric tends to crease more, the larger the load.
This is particularly the case for garments made from very fine
weave fabric, such as shirts or blouses.
Plinth filter
Only clean the plinth filter when the
indicator lights up.
To turn the indicator light off: Open and
close the door while the dryer is switched
on.
ĺPress the round,
indented area on
the heat
exchanger access
panel to open it.
The panel will
spring open.
ĺPull the plinth filter
out by the handle.
Removing the plinth filter will cause a
guide pin in the dryer to come out. This pin
ensures that the heat exchanger access
panel can only be closed if the plinth filter is
fitted.
ĺPull the handle
out of the plinth
filter.
ĺClean the filter
thoroughly under
running water.
ĺCarefully squeeze the water out of the
plinth filter.
The plinth filter must not be replaced
dripping wet.
ĺUse a damp
cloth to remove
any fluff from the
access panel.
Checking the heat exchanger unit
ɒRisk of injury from sharp cooling fins.
You could cut yourself.
Do not touch the cooling fins.
ĺCarefully vacuum
up any visible fluff
or dirt.
Refitting the plinth filter
ĺFit the filter back
on the handle the
right way.
ĺInsert the handle
with the plinth fil-
ter attached over
the two guide
pins.
The word Miele on the handle must be the
correct way up.
ĺClose the heat exchanger access panel.
Programme
Load
(weight of dry
laundry)
Items
Extra dry
Normal
Hand iron
Machine iron
Gentle tumble
Cottons 8 kg Cotton items such as those described under Cottons Normal with normal
residual moisture
X –
Cottons 8 kg Towelling, jersey wear, T-shirts, underwear, baby clothes, workwear,
covers, jackets, bathrobes, and flannelette bed linen
Warning: Do not use for jersey fabrics (e.g. T-shirts, underwear, Extra dry
baby clothes), as they have a tendency to shrink.
X X X X X
Minimum iron 4 kg Workwear, overalls, pullovers, dresses, trousers, leggings and table linen – X X – X
Delicates 2.5 kg Shirts, blouses, lingerie, appliquéd garments – X X – Always active
Woollens
handcare
2 kg Pullovers, cardigans, socks, stockings – – – – –
Shirts 2 kg Shirts and blouses – X X – X
Express 4 kg Garments suitable for the programme X X X X –Cottons
Denim 3 kg Jeans, jackets, skirts, shirts – X X – X
Bed linen 4 kg Bed linen X X X X –
Proofing 2.5 kg Microfibre fabric, skiwear, outerwear, fine close weave cotton garments
(poplin), tablecloths
Fire hazard! Do not use proofing agents containing paraffin.
– X – – –
Pre-ironing 1 kg Cotton trousers, anoraks, shirts – X X – Always active
Warm air 8 kg Thick and multi-layered jackets, pillows, sleeping bags, blankets – – – – X
X = Yes, – = No
Problem/Fault message Possible cause and remedy
lights up after a pro-
gramme is cancelled
The condensed water container is full or there is a kink in the
drain hose.
ĺEmpty the condensed water container.
ĺCheck the drain hose.
To switch off :
ĺOpen and close the door (with the dryer switched on).
lights up at the end
of a programme
There is a build-up of fluff (see "Cleaning and Care").
ĺClean the fluff filters.
ĺClean the plinth filter.
To switch off :
ĺOpen and close the door (with the dryer switched on).
lights up The programme selector has been moved.
ĺSelect the original programme again. The time remaining
will appear in the display.
Bars flash in the dis-
play at the end of a pro-
gramme: ……
…
The programme has finished but the laundry has not yet
cooled down.
ĺEither remove the laundry and spread it out to cool down
or leave it in the tumble dryer to cool down during the
cooling phase.
flashes/lights up
after the tumble dryer
is switched on and a
programme cannot be
selected
Access via a code has been activated.
ĺYou must enter the correct code to use the tumble dryer.
See "Programmable functions - PIN Code" in the
operating instructions.
The display is dark and
only the Start/Add laun-
dry sensor is flashing
This is not a fault, but a normal function.
ĺTouch a sensor to switch on the indicators.
See "Programmable functions - Control panel standby
status" in the operating instructions.
The drum will turn at intervals in the Anti-crease phase.
Problem/Fault message Possible cause and remedy
The dryer is switched
off at the end of the
programme
The tumble dryer switches off automatically. This is not a
fault, but a normal function.
The laundry is not suffi-
ciently dry
The load consisted of different types of fabric.
ĺFinish drying using the timed drying programme.Warm air
ĺSelect a more suitable programme next time.
Tip: You can alter the drying levels for some programmes.
See "Programmable functions - Cotton drying levels" and
" Minimum iron drying levels" in the operating
instructions.
Items made of synthetic
fibres are charged with
static electricity after
drying
Synthetic fibres tend to attract static charge.
Static charge can be reduced by adding fabric softener to
the final rinse in the washing programme.
There is a build-up of
fluff
Fluff is principally the result of friction when garments are
being worn and to some extent when they are being washed.
Machine drying hardly causes any fluff to form.
Fluff is collected by the fluff filters and the plinth filter and can
be removed easily.
See "Cleaning and care".
There are humming
noises
This is not a fault.
These noises are normal and caused by the operation of the
compressor.
Produktspezifikationen
| Marke: | Miele |
| Kategorie: | Trockner |
| Modell: | TWF720 WP |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Miele TWF720 WP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Trockner Miele
21 Mai 2024
10 Mai 2024
29 April 2024
26 April 2024
14 April 2024
11 April 2024
7 April 2024
6 April 2024
4 April 2024
2 April 2024
Bedienungsanleitung Trockner
- Trockner Sinbo
- Trockner Samsung
- Trockner Clatronic
- Trockner Emerio
- Trockner Coline
- Trockner Medion
- Trockner Nedis
- Trockner Hanseatic
- Trockner LG
- Trockner Adler
- Trockner Camry
- Trockner Trisa
- Trockner Bosch
- Trockner AEG
- Trockner Asko
- Trockner Siemens
- Trockner Bauknecht
- Trockner Electrolux
- Trockner Fagor
- Trockner Gorenje
- Trockner Klarstein
- Trockner Koenic
- Trockner Teka
- Trockner Whirlpool
- Trockner Bomann
- Trockner Vox
- Trockner Mesko
- Trockner Bush
- Trockner Thomson
- Trockner Amica
- Trockner BEKO
- Trockner Grundig
- Trockner Hotpoint
- Trockner Mio Star
- Trockner Schneider
- Trockner Sharp
- Trockner Smeg
- Trockner Tomado
- Trockner AEG-Electrolux
- Trockner Aliomatic
- Trockner Ardo
- Trockner Ariston
- Trockner Aspes
- Trockner Balay
- Trockner Bellavita
- Trockner Blomberg
- Trockner Scandomestic
- Trockner Brandt
- Trockner Candy
- Trockner Castor
- Trockner Comfee
- Trockner Constructa
- Trockner Corberó
- Trockner Daewoo
- Trockner Elektra Bregenz
- Trockner ELIN
- Trockner Eudora
- Trockner Eurotech
- Trockner Exquisit
- Trockner Mitsubishi
- Trockner GE
- Trockner Haier
- Trockner Hisense
- Trockner Hoover
- Trockner Hotpoint-Ariston
- Trockner Ignis
- Trockner Indesit
- Trockner Juno
- Trockner Kelvinator
- Trockner Maytag
- Trockner Midea
- Trockner Caple
- Trockner Neff
- Trockner Nordmende
- Trockner Otsein-Hoover
- Trockner Privileg
- Trockner Rommer
- Trockner Saivod
- Trockner ETNA
- Trockner Schulthess
- Trockner Frigidaire
- Trockner SIBIR
- Trockner Speed Queen
- Trockner Svan
- Trockner Thor
- Trockner V-ZUG
- Trockner Vestel
- Trockner Vestfrost
- Trockner Zanker
- Trockner Zanussi
- Trockner Zerowatt
- Trockner Pelgrim
- Trockner Philco
- Trockner Akai
- Trockner Arçelik
- Trockner Continental Edison
- Trockner Tesla
- Trockner ProfiCare
- Trockner Bimar
- Trockner DeLonghi
- Trockner Element
- Trockner Leifheit
- Trockner Ariete
- Trockner Remington
- Trockner Morris
- Trockner Cylinda
- Trockner MPM
- Trockner UPO
- Trockner Thomas
- Trockner Logik
- Trockner Orima
- Trockner Proline
- Trockner Westinghouse
- Trockner Amana
- Trockner Gram
- Trockner Omega
- Trockner Profilo
- Trockner Lamona
- Trockner Kogan
- Trockner Royal Sovereign
- Trockner New Pol
- Trockner Aurora
- Trockner Danby
- Trockner Vedette
- Trockner Auto Joe
- Trockner Ariston Thermo
- Trockner RCA
- Trockner Fisher & Paykel
- Trockner Esatto
- Trockner Gibson
- Trockner CDA
- Trockner General Electric
- Trockner Seiki
- Trockner Defy
- Trockner Jocel
- Trockner Kenmore
- Trockner Lavorwash
- Trockner Magic Chef
- Trockner Marynen
- Trockner Stirling
- Trockner Avanti
- Trockner Kunft
- Trockner Simpson
- Trockner Roper
- Trockner Mabe
- Trockner Amba
- Trockner Classique
Neueste Bedienungsanleitung für -Kategorien-
16 August 2024
14 August 2024
13 August 2024
6 August 2024
6 August 2024
1 Juli 2024
1 Juli 2024
30 Juni 2024