Midea Oasis MSOW Bedienungsanleitung

Midea Klimaanlage Oasis MSOW

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Midea Oasis MSOW (2 Seiten) in der Kategorie Klimaanlage. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

1. Determine hole positions according to left and right

side of the installation plate. The hole center is obtained

by measuring the distance as shown in the diagram above.

2. Dirll the piping plate hole with 65mm hole-core drill.

3. Drill the piping hole at either the right or the left and the

hole should be slightly slanted to the outdoor side.

4. Always take steps to protect the pipe when drilling metal

grid,metal plate or the like.

INSTALLATION MANUAL FOR

ROOM AIR CONDITIONER

(Split Wall-Mounted Type)

DRILL A HOLE IN THE WALL

INSTALLATION PLATE MOUNTING

Please read these safety precautions carefully before installation

Be sure to follow all the precautions below, they are all important for ensuring safety.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to property.

1) This equipment must be grounded and installed with ground leakage current breaker. It may cause

electrical shock if grounding is not perfect.

2) Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and

accumulates at surrounding of the unit, it may cause fire.

3) Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water

may enter the room and damage the furniture.

1) Install according to this installation instructions strictly. If installation is defective, it will cause water

leakage, electrical shock,or fire.

2) Use the included accessories parts and specified parts for installation. otherwise, it will cause the set

to fall, water leakage, electrical shock,or fire.

3) Install at a strong and firm location which is able to withstand the set s weight. If the strength is not

enough or installation is not properly done, the set will drop and cause injury.

4) For electrical work, follow the local national wiring standard, regulation and this installation instructions.

An independent circuit and single outlet must be used. If electrical circuit capacity is not enough or

defect found in electrical work, it will cause electrical shock,or fire.

5) Use the specified cable and connect tightly and clamp the cable so that no external force will be acted

on the terminal. If connection or fixing is not perfect, it will cause heat-up or fire at the connection.

6) Wiring routing must be properly arranged so that control board cover is fixed properly. If control board

cover is not fixed perfectly, it will overheat at connection point of terminal, fire or electrical shock.

7) When carrying out piping connection, take care not to let air substances other than the specified

refrigerant go into refrigeration cycle. Otherwise, it will cause lower capacity,abnormal high pressure

in the refrigeration cycle, explosion and injury.

8) Do not modify the length of the power supply cord or use of extension cord, and do not share the

single outlet with other electrical appliances. Otherwise, it will cause fire or electrical shock.

SAFETY PRECAUTIONS

CAUTION

WARNING

CAUTION

WARNING

Please read this installation manual carefully before operating the unit to ensure correct installation.

If the power cord is damaged, replacement work shall be performed by authorised personnel only.

Installation work must be performed in accordance with the national wiring standards by authorised

personnel only.

Contact an authorized service technician for repair, maintenance and installation of this unit.

This appliance is not intended for use by persons(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by persons responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

All the pictures in the instructions are for explanation purposes only. The actual shape should prevail.

The design and specifications are subject to change without prior notice for product improvement.

Consult with the sales agency or manufacturer for details.

There should not be any heat source or stream

near the unit.

There should not be any obstacles blocking the

air circulation.

A place where air circulation in the room is good.

A place where drainage can be easily done.

A place where noise prevention is taken into

consideration.

Do not install the unit near the door way.

Ensure the spaces indicated by arrows from the

wall,ceiling,fence or other obstacles.

There should not be any direct sunlight. If unavoidable,

sunlight prevention should be taken into consideration.

Outdoor unit dimension

mm(WxHxD)

A(mm) B(mm)

530 290

560

549

640

335

325

404

481

549

276

Mounting dimensions

670x540x265

780x540x250

760x590x285

845x700x320

810x558x310

940x810x375

Indoor unit

Outdoor unit

If an awning is built over the unit to prevent

direct sunsight or rain,be careful that heat

radiation from the condenser is not obstructed.

There should not be any animal or plant which

could be affected by hot air discharged.

Keep the spaces indicated by arrow from wall

ceiling, fence or other obstacles.

Do not place any obstacles which may cause

a short circuit of the discharged air.

Anchor the outdoor unit with a bolt and nut 10 or

8 tightly and horizontally on a concrete or rigid mount.

Settlement of outdoor unit

NOTE: The outdoor unit you purchase may be like one

of the following. Install the outdoor unit according to the

dimension as indicated in the table below:

Air inlet

Air outlet

Air inlet

INSTALLATION PRECAUTIONS

CONNECT THE CABLE TO THE INDOOR UNIT

Terminal block of indoor unit

Connect the cable to the indoor unit

Before performing any electrical work, turn off the main power to the system.

1. The inside and outside connecting cable can be connected without removing the front grille.

2. The indoor power cord type is H05VV-F or H05V2V2-F, the outdoor power cord and

interconnected cord type is H07RN-F.

3. Lift the indoor unit panel up, remove the electrical box cover by loosening the screw.

4. Ensure the colour of wires of outdoor unit and the terminal Nos. are the same to the indoor s

respectively.

5. Wrap those cables not connected with terminals with insulation tapes, so that they will not touch

any electrical components. Secure the cable onto the control board with the cord clamp.

NOTE:

Electronic box

cover

Front Panel

To outdoor unit

Model A Model B

To outdoor unit

L(1)

2(N)

1(L)

Installation Plate

Clip Anchor

Self-tapping Screw A ST3.9x25

Seal(For cooling & heating models only)

Drain Joint(For cooling & heating models only

Connecting

pipe

Assembly

Liquid side

Gas side

Remote controller

Self-tapping Screw B ST2.9x10

6.35

9.52

12.7

Parts you must purchase. The pipe

size differ from appliance to appliance.

Consult the technician for the proper

size.

5-8(depending on models)

Except the above parts provided,the other parts needed during installation you must

purchase.

Remote controller holder

ACCESSORIES

Number

Name of Accessories Qty

NOTE:

optional

parts

SELECT THE BEST LOCATION

NOTE: If used as MONO unit, for the standby control needs, the cross section area of cable connected

to L(1)/W, 1/1(L), 2(N) must be sufficient for the maximum system current. The maximum system current

is equal to the sum of indoor unit and outdoor unit rated current. If used as MULTI unit, L(1)/W on the

terminal block does not need to be connected.

CONNECTIVE PIPE AND DRAINAGE INSTALLATION

1. Run the drain hose sloping downward.

Do not install the drain hose as illustrated

in wrong figures.

2. When connecting extension drain hose,

insulate the connecting part of extension

drain hose with a shield pipe, do not let

the drain hose slack.

Drainage

Right Wrong

Correct orientation

of Installation Plate

1. Fit the installation plate horizontally on

structural parts of the wall withspaces

around the installation plate.

2. If the wall is made of brick, concrete

or the like, drill five or eight 5mm

diameter holes in the wall. Insert

clip anchor for appropriate mounting

screws.

3. Fit the installation plate on the wall

with five or eight type A screws.

Mount the Installation Plate and drill

holes in the wall according to the wall

structure and corresponding mounting

points on the installation plate. The

installation plate providedwith the

machine differ from appliance

to appliance.(Dimensions are in

mm unless otherwise stated)

NOTE:

Installation Plate Mounting

The mounting wall is strong and solid enough

to prevent it from the vibration.

280

120mm or

more to wall

120mm or

more to wall

120mm or

more to wall

150mm or more to ceiling

Left rear side

refrigerant

pipe hole 65

36.5

835

140 110

Left rear side

refrigerant

pipe hole 65

Right rear side

refrigerant

pipe hole 65

Right rear side

refrigerant

pipe hole 65

Indoor unit outline

120mm or

more to wall 120mm or

more to wall

Indoor unit outline

990

315

135

260

150mm or more to ceiling

Left rear side

refrigerant

pipe hole 65 Right rear side

refrigerant pipe

hole 65

Model C

Model B

Model A

120mm or

more to wall

36.5

750

180 110

280

202000192486 CS159I1-BP11M(L) 20140515

Air freshening filter(used to install on Air filter)

Electric safety regulations for the initial Installation

1. If there is serious safety problem about the power supply, the technicians should refuse to install

the air conditioner and explain to the client until the problem is solved.

2. Power voltage should be in the range of 90%~110%of rated voltage.

3. The surge protector and main power switch with a 1.5 times capacity of Max. Current of the unit should

be installed in power circuit. Ensure the air conditioner is grounded well.

4. The appliance shall be installed in accordance with national wiring regulations. Do not operate your air

conditioner in a wet room such as a bathroom or laundry room.

5. An all-pole disconnection device which has at least 3mm clearances in all poles, and have a leakage

current that may exceed 10mA, the residual current device(RCD) having a rated residual operating

current not exceeding 30mA, and disconnection must be incorporated in the fixed wiring in accordance

with the wiring rules.

6. For the unit adopts auxiliary electric heater, keep at least 1 meter away from the nearest combustible

materials.

7. According to the attached Electrical Connection Diagram located on the panel of the indoor & outdoor

unit to connect the wire.

8. All wiring must comply with local and national electrical codes and be installed by qualified and

skilled electricians.

9. An individual branch circuit and single receptacle used only for this air conditioner must be

available. See the following table for suggested wire sizes and fuse specifications:

Minimum cross-sectional area of conductors:

Rated curr ent

of appliance

(A)

>3 and 6

>6 and 10

>10 and 16

>16 and 25

>25 and 32

>32 and 40

Nominal cross-sectional

area

(mm2)

0.75

1.5

2.5

Electrical work

The wire size of power supply cord and

interconnected wire and the current of

the fuse or switch are determined by the

maximum current indicated on the

nameplate which located on the side

panel of the unit. Please refer to the

nameplate before selecting the wire size,

fuse or switch.

The controller of the air conditioner

designed with a fuse protection function

under abnormal conditions, the

specifications of the fuse have printed on

the circuit board, such as: T3.15A/250VAC,

T5A/250VAC, etc.

NOTE:

Install the outdoor unit on a rigid base to prevent increasing noise level and vibration.

Determine the air outlet direction where the discharged air is not blocked.

In the case that the installation place is exposed to strong wind such as a seaside, make

sure the fan operating properly by putting the unit lengthwise along the wall or using a dust

or shield plates.

Specially in windy area, install the unit to prevent the admission of wind. If need suspending

installation, the installation bracket should accord with technique requirement in the

installation bracket diagram. The installation wall should be solid brick, concrete or the same

intensity construction, or actions to reinforce, damping supporting should be taken.

The connection between bracket and wall, bracket and the air conditioner should be firm,

stable and reliable.

Be sure there is no obstacle which block radiating air.

Strong

wind

Strong

wind

Barrier

Incorrect Correct

Seal

Drain joint

Base pan hole

of outdoor unit

(A) (B)

The drain joint is slightly different according to the

different outdoor unit.

For the drain joint with the seal(Fig.A), first fit the seal onto

the drain joint, then insert the drain joint into the base pan

hole of outdoor unit, rotate 90 to securely assemble them.

To install drain joint as shown in Fig.B, insert the drain

joint into the base pan hole of outdoor unit until it remains

fixed with a clicking sound. Connecting the drain joint with

an extension drain hose (Locally purchased), in case of the

water draining off the outdoor unit during the heating mode.

DRAIN JOINT INSTALLATION

OUTDOOR INSALLATION PRECAUTION

REFRIGERANT PIPE CONNECTION

1. Cut a pipe with a pipe cutter.

2. Put flare nuts on pipe/tube having

completed burr removal and flare the pipe.

3. Firmly hold copper pipe in a die in the

dimension shown in the table below.

Align pipes to be connected.

Sufficiently tighten the flare nut with fingers,

and then tighten it with a spanner and torque

wrench as shown.

Excessive torque can break nut depending

on installation conditions.

Outer diam.

(mm)

A(mm)

Max. Min.

6.35 1.3 0.7

9.52

1.6 1.0

12.7

1.8 1.0

12.7

1.8

2.2

1.0

2.0

Bar

Copper pipe Clamp handle

Handle

Bar

"A"

Indoor unit tubing Flare nut Pipings

Outer

diam. Tightening

torque(N.cm) Additional tightening

torque(N.cm)

6.35mm

12.7mm

16mm

9.52mm

1500

(153kgf.cm) 1600

(163kgf.cm)

3500

(357kgf.cm)

4500

(459kgf.cm)

3600

(367kgf.cm)

4700

(479kgf.cm)

2500

(255kgf.cm)

2600

(265kgf.cm)

AIR PURGING AND TEST OPERATION

1. Remove the electrical control board cover from the outdoor unit by loosening the screw.

2. Connect the connective cables to the terminals as identified with their respective matched numbers

on the terminal block of indoor and outdoor units.

3. Secure the cable onto the control board with the cord clamp.

4. To prevent the ingress of water, form a loop of the connective cable as illustrated in the installation

diagram of indoor and outdoor units.

5. Insulate unused cords (conductors) with PVC-tape. Process them so they do not touch any electrical

or metal parts.

Cover

Screw

Terminal block of outdoor unit

Liquid side: 6.35mm

R22: (Pipe length-5)x30g/m

R410A: (Pipe length-5)x15g/m

Liquid side: 9.52mm:

R22: (Pipe length-5)x60g/m

R410A: (Pipe length-5)x30g/m

Connective pipe length

Less than 5m

More than 5m

Air purging method

Use vacuum pump

Additional amount of refrigerant to be charged

Open the valve stem until it hits against

the stopper. Do not try to open it further.

Securely tighten the valve stem cap with

a spanner or the like.

Valve stem cap tightening torque. See

Tightening torque table.

Flare nut

Stopper

Cap

Valve body

Valve stem

Use vacuum pump

For the R410A refrigerant model, make sure the refrigerant added into air conditioner is liquid

form in any cases.

When relocating the unit to another place, using vacuum pump to perform evacuation.

The indoor unit and tubing between the indoor and outdoor unit must be leak tested and evacuated

to remove any noncondensables and moisture from the system.

Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have

been properly connected and all wiring for the test run has been completed.

Pipe length and refrigerant amount:

Outdoor

unit

Indoor

unit

Refrigerant

Packed valve

Flare nut

Gas side

Liquid side

1. Completely tighten the flare nuts, A, B, C, D, connect

the manifold valve charge hose to a charge port of the

packed valve on the gas pipe side.

2. Connect the charge hose connection to the vacuum

pump.

3. Fully open the handle Lo of the manifold valve.

4. Operate the vacuum pump to evacuate. After starting

evacuation, slightly loose the flare nut of the packed

valve on the gas pipe side and check that the air is

entering. (Operation noise of the vacuum pump changes

and a compound meter indicates 0 instead of minus)

5. After the evacuation is complete, fully close the handle

Lo of the manifold valve and stop the operation of the

vacuum pump.

Make evacuation for 15 minutes and more and check

that the compound meter indicates -76cmHg(-1.0x10 Pa).

6. Turn the stem of the packed valve B about 45 counter-

clockwise for 6~7 seconds after the gas coming out, then

tighten the flare nut again. Make sure the pressure display

in the pressure indicator is a little higher than the atmosphere

pressure.

7. Remove the charge hose from the Low pressure charge hose.

8. Fully open the packed valve stems B and A.

9. Securely tighten the cap of the packed valve.

Manifold valve

Compound meter

-76cmHg

Handle Lo Handle Hi

Charge hose Charge hose

Vacuum pump

Pressure gauge

Packed valve

Perform test operation after completing gas leak check at the flare nut connections and electrical

safety check.

Check that all tubing and wiring have been properly connected.

Check that the gas and liquid side service valves are fully open.

1. Connect the power, press the ON/OFF button on the remote controller to turn the unit on.

2. Use the MODE button to select COOL, HEAT, AUTO and FAN to check if all the functions works

well.

3. When the ambient temperature is too low(lower than 17 C), the unit cannot be controlled by the

remote controller to run at cooling mode, manual operation can be taken. Manual operation is

used only when the remote controller is disable or maintenance necessary.

Hold the panel sides and lift the panel up to an angle until it remains fixed with a clicking sound.

Press the Manual control button to select the AUTO or COOL, the unit will operate under Forced

AUTO or COOL mode(see User Manual for details).

4. The test operation should last about 30 minutes.

Flaring

Tightening connection

1. Air purging

2. When using the Vacuum Pump

4. Test running

3. Safety and leakage check

A: Lo packed valve B: Hi packed valve

C and D are ends of indoor unit connection.

CAUTION

1. Soap water method:

Apply a soap water or a liquid neutral detergent on the indoor

unit connections and outdoor unit connections by a soft brush

to check for leakage of the connecting points of the piping. If

bubbles come out, it indicates that the pipes have leakage.

2. Leak detector

Use the leak detector to check for leakage.

CONNECT THE CABLE TO THE OUTDOOR UNIT

CAUTION

Indoor unit

check point D

Outdoor unit

check point

Cover

NOTE:

To indoor unit To indoor unit

Power supply

Model A Model B

Power supply

Oblique

Roughness

Burr

AUTO/COOL

Manual control button

Connect the indoor unit first, then the

outdoor unit.

Do not allow the piping to let out from the

back of the indoor unit.

Be careful not to let the drain hose slack.

Heat insulation should be done to the

extension drain hose of indoor unit.

Be sure that the drain hose is located at

the lowest side of the bundle. Locating at

the upper side can cause drain pan to

overflow inside the unit.

Never intercross nor intertwist the power

wire with any other wiring.

1. Pass the piping through the hole in the wall.

2. Hook the indoor unit onto the upper portion

of installation plate(Engage the indoor unit with

the upper edge of the installation plate). Ensure

the hooks are properly seated on the installation

plate by moving it in left and right.

3. Piping can easily be made by lifting the indoor

unit with a cushioning material between the

indoor unit and the wall. Get it out after finish

piping.

4. Press the lower left and right side of the unit

against the installation plate until hooks

engages with the their slots.

CAUTION

Indoor unit installation

1. For the left-hand and right-hand piping,

remove the pipe cover from the side panel.

2. For the right back and left back piping,

install the piping as shown.

NOTE:

3. Bundle the tubing, connecting cable, and

drain hose with tape securely, evenly as

shown in Figure on the right.

For 9K/12K model, there is only one

side drainage structure design. For 18k

model, one side drainage structure is standard.

Both sides drainage structure is optional

and can only be customized from factory.

For both sides drainage structure, it can be

choosen for right, left or both sides drainage

connection. If choosing both sides drainage

connection, another proper drain hose is

needed as there is only one drain hose offered

by factory. If choosing one side drainage

connection, make sure the drain hole on the

other side is well plugged. The connection of

the drain hose is supposed to be done by

qualified installer in case of water leakage.

Connective pipe installation

Because the condensed water from rear

of the indoor unit is gathered in ponding

box and is piped out of room. Do not put

anything else in the box.

NOTE: Connective pipe length will affect the capacity and energy efficiency of the unit. The

nominal efficiency is tested basing on the pipe length of 5 meters.

Produktspezifikationen

Marke:	Midea
Kategorie:	Klimaanlage
Modell:	Oasis MSOW

Brauchst du Hilfe?

Wenn Sie Hilfe mit Midea Oasis MSOW benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Klimaanlage Midea

Midea MTA12CR81 Bedienungsanleitung

4 Oktober 2024

Midea MAT12R2ZWT Bedienungsanleitung

29 September 2024

Midea MPF14CEN2 Bedienungsanleitung

17 September 2024

Midea MOX401-24HFN8 Bedienungsanleitung

17 September 2024

Midea MSAFB-09CRDN8-QC0 Bedienungsanleitung

17 September 2024

Midea Vertu Design Bedienungsanleitung

15 September 2024

Midea MST2I-09HRIN1 Bedienungsanleitung

13 September 2024

Midea MOB02-18HFRN8 Bedienungsanleitung

11 September 2024

Midea MTA3-18HRN1 Bedienungsanleitung

9 September 2024

Midea MAP06R1BWT Bedienungsanleitung

5 September 2024

Bedienungsanleitung Klimaanlage

Neueste Bedienungsanleitung für -Kategorien-

MundoClima MUCSR-H3 Bedienungsanleitung

16 Oktober 2024

Duux DXMA10 North Bedienungsanleitung

16 Oktober 2024

Duux DXAC04 Bedienungsanleitung

16 Oktober 2024

LG HS-H076QPA0 Bedienungsanleitung

16 Oktober 2024

Klarstein Vita Pure 2G Bedienungsanleitung

16 Oktober 2024

Einhell BMK 2400E Bedienungsanleitung

15 Oktober 2024

Qlima P 126 Bedienungsanleitung

15 Oktober 2024

Amana PTC093K35AXXX Bedienungsanleitung

15 Oktober 2024

Amana AMAP121AB-2 Bedienungsanleitung

15 Oktober 2024

Amana PTC173J35AXXX Bedienungsanleitung

15 Oktober 2024