Metabo WH36DC Bedienungsanleitung
Metabo
Bohrmaschine
WH36DC
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr Metabo WH36DC (76 Seiten) in der Kategorie Bohrmaschine. Dieser Bedienungsanleitung war fĂŒr 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/76
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual BEFORE operating the power tool. Please keep this manual available for other
users and owners before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE DâEMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraßner la mort
ou de sérieuses blessures corporelles!
Ce mode dâemploi contient dâimportantes informations Ă propos de la sĂ©curitĂ© de ce produit.
PriĂšre de lire et de comprendre ce mode dâemploi AVANT dâutiliser lâoutil motorisĂ©. Garder ce
mode dâemploi Ă la disponibilitĂ© des autres utilisateurs et propriĂ©taires avant quâils utilisent
lâoutil motorisĂ©. Ce mode dâemploi doit ĂȘtre conservĂ© dans un endroit sĂ»r.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¥La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar
en lesiones de gravedad o la muerte!
Este manual contiene informaciĂłn importante sobre la seguridad del producto. Lea y
comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para
que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe
ser guardado en un lugar seguro.
Model
ModĂšle
Modelo WH 36DC
Cordless Impact Driver
Marteau Ă choc sans ïŹ l
Atornillador de impacto inalĂĄmbrico
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before
operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,
and by observing appropriate safety procedures.
Basic safety precautions are outlined in the âSAFETYâ section of this Instruction Manual and in the sections which
contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identiïŹ ed by WARNINGS on the power
tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been speciïŹ cally recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and speciïŹ cations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, ïŹ re and/or serious injury.
Save all warnings and instructions for future reference.
The term âpower toolâ in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
ïŹ ammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
UnmodiïŹ ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
2
English
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the inïŹ uence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-
skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the oïŹ -position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your ïŹ nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.
Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.
A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and oïŹ .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or
storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may aïŹ ect the power toolâs operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations diïŹ erent
from those intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger speciïŹ ed by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of ïŹ re when used with
another battery pack.
3
English
SPECIFIC SAFETY RULES AND SYMBOLS
1. Hold power tools by insulated gripping surfaces,
when performing an operation where the
fastener may contact hidden wiring.
Fasteners contacting a âliveâ wire may make exposed
metal parts of the power tool âliveâ and could give the
operator an electric shock.
2. ALWAYS wear ear protectors when using the tool
for extended periods.
Prolonged exposure to high intensity
noise can cause hearing loss.
3. NEVER place hands or other body parts near the drill
bit or chuck during operation. Hold the impact driver
by its handle only.
4. Because the cordless impact driver operates by
battery power, be aware of the fact that it can begin to
operate at any time.
5. When working at elevated locations, clear the area
of all other people and be aware of conditions below
you.
6. NEVER touch moving parts.
NEVER place your hands, ïŹ ngers or other body parts
near the toolâs moving parts.
7. NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the
tool.
8. Use right tool.
Donât force small tool or attachment to do the job of a
heavy-duty tool.
Donât use tool for purpose not intended âfor
exampleâ donât use circular saw for cutting tree
limbs or logs.
9. NEVER use a power tool for applications other
than those speciïŹ ed.
NEVER use a power tool for applications other than
those speciïŹ ed in the Instruction Manual.
10. Handle tool correctly.
Operate the tool according to the instructions provided
herein. Do not drop or throw the tool. NEVER allow the
tool to be operated by children, individuals unfamiliar
with its operation or unauthorized personnel.
11. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
b) Use power tools only with speciïŹ cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and ïŹ re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.
Shorting the battery terminals together may cause
burns or a ïŹ re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ïŹ ush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause irritation
or burns.
e) Do not use a battery pack or tool that is
damaged or modiïŹ ed.
Damaged or modiïŹ ed batteries may exhibit
unpredictable behaviour resulting in ïŹ re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to ïŹ re or
excessive temperature.
Exposure to ïŹ re or temperature above 265 °F may
cause explosion.
g) Follow all charging instructions and do
not charge the battery pack or tool outside
the temperature range speciïŹ ed in the
instructions.
Charging improperly or at temperatures outside
the speciïŹ ed range may damage the battery and
increase the risk of ïŹ re.
6) Service
a) Have your power tool serviced by a
qualiïŹ ed repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service
providers.
â WARNING â
To reduce the risk of injury, user must read
instruction manual.
4
English
12. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the toolâs housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
13. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to yourself or others. Blades,
cutting implements and accessories which have been
mounted to the tool should be secure and tight.
14. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually, making
strange noises, or otherwise appears defective, stop
using it immediately and arrange for repairs by a
metabo HPT authorized service center.
15. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
16. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
17. Always wear eye protection that meets the
requirement of the latest revision of ANSI
Standard Z87.1.
18. Do not use the product if the tool or the battery
terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
19. Keep the toolâs terminals (battery mount) free of swarf
and dust.
â
Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
â
During use, try to avoid swarf or dust on the tool from
falling on the battery.
â
When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result
in smoke emission or ignition.
20. DeïŹ nitions for symbols used on this tool
V ............ volts
â
--- ......... direct current
no .......... no load speed
---/min .... revolutions or reciprocation per minute
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE CORDLESS IMPACT
DRIVER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of the cordless impact
driver. To avoid these risks, follow these basic
safety instructions:
1. NEVER use this impact driver handle for any
application other than those in this manual.
2. NEVER place hands or other body parts near the drill
bit or chuck during operation.
Hold the impact driver by its handle only.
3. When working in high places, always make sure that
ther is no one below before starting to work.
4. ALWAYS wear eye and ear protection when you work.
5. ALWAYS install the driver bit securely. A loose bit is
dangerous because it can come loose while you are
working.
6. ALWAYS use the driver bit that matches the screw
size.
7. ALWAYS have the screw you are screwing in and
this impact driver in a straight line. Working with this
impact driver at an angle to the screw can damage the
screw head and will not give the prescribed tightening
torque.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers.
To avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YSL3.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT
rechargeable battery models of the multi volt series
and the BSL18 series. Other models of batteries may
burst causing personal injury and damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of ïŹ re, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
5
English
6. Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of ïŹ re and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as speciïŹ ed in Table 1.
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes* AWG Size of Cord
Equal to or
greater than
but less
than
Length of Cord, Feet (Meter)
25 (7.5) 50 (15) 100 (30) 150 (45)
0 2 18 18 18 16
2 3 18 18 16 14
3 4 18 18 16 14
* If the input rating of a battery charger is given in watts
rather than in amperes, the corresponding ampere
rating is to be determined by dividing the wattage
rating by the voltage ratingâfor example:
1,250 watts = 10 amperes
125 volts
8. Do not operate battery charger with damaged cord or
plug-replace them immediately.
9. Do not operate battery charger if it has received a
sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualiïŹ ed serviceman.
10. Do not disassemble battery charger; take it to a
qualiïŹ ed serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or ïŹ re.
11. To reduce risk of electric shock, unplug charger from
receptacle before attempting any maintenance or
cleaning. Removing the battery will not reduce this
risk.
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
BATTERY CHARGER
You must charge the battery before you can use the power
tool. Before using the model UC18YSL3 battery charger,
be sure to read all instructions and cautionary statements
on it, the battery and in this manual.
CAUTION
USE ONLY metabo HPT BATTERY MODELS OF
THE MULTI VOLT SERIES. OTHER MODELS OF
BATTERIES MAY BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING:
Improper use of the battery
or battery charger can lead to
serious injury. To avoid these
injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged or
is completely worn out. The battery can explode in a
ïŹ re.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery chargerâs
air vents. Electric shock or damage to the battery
charger may result.
5. NEVER charge outdoors. Keep the battery away
from direct sunlight and use only where there is low
humidity and good ventilation.
6. NEVER charge when the temperature is below 32°F
(0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the
battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use DC power to charge.
11. NEVER store the battery or battery charger in places
where the temperature may reach or exceed 104°F
(40°C) such as inside metal box or car.
12. NEVER expose the battery or battery charger to rain
or wet conditions.
13. ALWAYS operate charger on standard household
electrical power (120 volts). Using the charger on any
other voltage may overheat and damage the charger.
6
English
8. Do not put or subject the battery to high temperatures
or high pressure such as into a microwave oven,
dryer, or high pressure container.
9. Keep away from ïŹ re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears
abnormal during use, recharging or storage,
immediately remove it from the equipment or battery
charger, and stop use.
12. Do not immerse the battery or allow any ïŹ uids to ïŹ ow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in ïŹ re or explosion. Store your
battery in a cool, dry place, away from combustible
and ïŹ ammable items. Corrosive gas atmospheres
must be avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you ïŹ nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the ïŹ rst time, do not use and return it to
your supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of ïŹ re. Please observe the
following matters when storing the battery.
â
Do not place electrically conductive cuttings,
nails, steel wire, copper wire or other wire in the
storage case.
â
Either install the battery in the power tool or store
by securely pressing into the battery cover until
the ventilation holes are concealed to prevent
short-circuits (See Fig. 3).
14. ALWAYS wait at least 15 minutes between charges to
avoid overheating the charger.
15. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
â
During work make sure that swarf and dust do not fall
on the battery.
â
Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
â
Do not store an unused battery in a location exposed
to swarf and dust.
â
Before storing a battery, remove any swarf and dust
that may adhere to it and do not store it together with
metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject
the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
speciïŹ ed.
7. If the battery charging fails to complete even when a
speciïŹ ed recharging time has elapsed, immediately
stop further recharging.
7
English
PRECAUTIONS REGARDING THE DUST-RESISTANCE AND WATER-PROOFING
FUNCTIONS
This product conforms to IP56 protection class ratings (dust-resistance and water-prooïŹ ng) for electrical equipment as
stipulated by the international IEC regulations. (Only the main unit conforms to the IP56 protection class ratings when
equipped with a battery.)
[Descriptions of IP Codes]
IP56
Protection rating for water penetration
Must be no adverse eïŹ ects on the equipment when sprayed with powerful jets of water from all directions
(water-proofed).
(100 L of water per minute sprayed for approximately three minutes from a distance of approximately three
meters with the use of a spray nozzle with a diameter of 12.5 mm.)
Protection rating for external assault by solid objects
Dust that may cause adverse eïŹ ects on the equipment must not be able to enter (dust-resistance).
(The equipment to be left non-operable in a test chamber in which particles of talcum powder with a diameter
of less than 75 ÎŒm are ïŹ oating in the air with the use of an agitation pump at a rate of 2 kg per cubic meter for
eight hours.)
The equipment has been designed to withstand the eïŹ ects of dust and water, but there is no guarantee that it will not
malfunction. Do not use or leave the equipment in locations where it is subject to excessive amounts of dust, or in
locations where it is submerged in water or subject to rainwater.
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS TOOL!
9
English
SPECIFICATIONS
1. Cordless Impact Driver
Model WH36DC
No-load
speed
Power mode 0â3,400 /min
Bolt mode/Bolt single mode 0â2,900 /min
Soft mode 0â900 /min
Self drilling screw mode 0â3,700 /min
Capacity
Small screw 5/32" (M4)â3/8" (M10)
Ordinary bolt 3/16" (M5)â23/32" (M18)
High tension bolt 3/16" (M5)â9/16" (M14)
Self drilling screw Ï Ï3.5â 6
Tightening torque
Maximum 1,903 in-lbs {215 Nâm 2,192 kgfâcm}
Tightening is 5/8" (M16) high tension bolt, when fully
charged at 68°F (20°C) temp.
Tightening time: 3 sec.
Bit shank size 1/4" (6.35 mm) Hex.
Battery*
Model BSL36A18
Type Li-ion battery
Voltage DC 36 V / 18 V
Weight (BSL36A18 attached) 3.5 lbs. (1.6 kg)
* Existing batteries (BSL3660/3626/3620, BSL18xx and BSL14xx series, etc.) cannot be used with this tool.
2. Battery Charger
Model UC18YSL3
Input power source Single phase: AC 120 V 60 Hz
Charging time
(At a temperature of 68°F (20°C)) BSL36A18 : Approx. 32 min
Charging voltage DC 14.4â18 V
Charging current DC 8.0 A
Weight 1.3 lbs. (0.6 kg)
NOTE: The charging time may vary according to temperature and power source voltage.
11
English
ASSEMBLY AND OPERATION
1. Connect the chargerâs power cord to a receptacle.
When the power cord is connected, the charge
indicator lamp will blink in red. (At 1-second intervals)
WARNING
Do not use the electrical cord
if damaged. Have it repaired
immediately.
2. Insert the battery to the battery charger.
Firmly Insert the battery into the battery charger as
shown in Fig. 6.
Charge
indicator lamp
Guide rail
Battery
Fig. 6
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the
charge indicator lamp will light up in green.(See
Table 2)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be
as shown in Table 2, according to the condition of the
battery charger or the battery.
APPLICATIONS
â Driving and removing of machine screws, wood
screws, tapping screws, etc.
REMOVAL AND INSTALLATION METHOD
OF BATTERY
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (see Fig. 5).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 5).
Push
Insert
Battery
Pull out
Handle
Latch
Fig. 5
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the
following points.
â
The power source voltage is stated on the nameplate.
â
The cord is not damaged.
WARNING
Do not charge at voltage higher than indicated
on the nameplate.
If charged at voltage higher than indicated on the
nameplate, the charger will burn out.
12
English
7. Remaining battery indicator
You can check the batteryâs remaining capacity by
pressing the remaining battery indicator switch to light
the indicator lamp. (Fig. 14, Table 5)
The indicator will shut oïŹ approximately 3 seconds
after the remaining battery indicator switch is pressed.
It is best to use the remaining battery indicator as
a guide since there are slight diïŹ erences such as
ambient temperature and the condition of the battery.
Also, the remaining battery indicator may vary from
those equipped to a tool or charger.
Display panel
Remaining battery
indicator lamp
Remaining battery
indicator switch
Fig. 14
Table 5
State of lamp Battery Remaining Power
Lights ;
The battery remaining power is
over 75%.
Lights ;
The battery remaining power is
50%â75%.
Lights ;
The battery remaining power is
25%â50%.
Lights ;
The battery remaining power is
less than 25%.
Blinks ;
The battery remaining power
is nearly empty. Recharge the
battery soonest possible
Blinks ;
Output suspended due to high
temperature. Remove the
battery from the tool and allow it
to fully cool down.
â
When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
â
The rotational speed can be controlled by varying
the amount that the trigger switch is pulled. Speed
is low when the trigger switch is pulled slightly and
increases as the trigger switch is pulled more.
â
When releasing the trigger switch, the brake will be
applied for immediate stopping.
NOTE
A buzzing noise is produced when the motor is about
to rotate; this is only a noise, not a machine failure.
6. Using the hook
The hook is used to hang up the power tool to your
waist belt while working.
CAUTION
â
When using the hook, hang up the power tool
ï rmly not to drop accidentally.
If the power tool is dropped, it may lead to an
accident.
â
When electing to carry the tool hooked to your
hip belt, make sure to detach the tool bit and side
handle.
Failure to do so may result in unexpected injury.
â
Install securely the hook. Unless the hook is
securely installed, it may cause an injury while
using.
(1) Removing the hook.
Remove the screws ï xing the hook with Philips screw
driver. (Fig. 12)
Hook
Screw
Groove
Fig. 12
(2) Replacing the hook and tightening the screws.
Install securely the hook in the groove of power
tool and tighten the screws to ï x the hook ï rmly.
(Fig. 13)
Screw
Hook
Groove
Fig. 13
16
English
1. Battery (BSL36A18)
2. Phillips bit
2"(50mm)
Bit No. Code No.
No.2 992671
No.3 992672
3. Hexagonal socket
Part Name Engraved
characters L B Code No.
4 mm Hexagonal socket 7 65 7 992689
5 mm Hexagonal socket 8 65 8 996177
6 mm Hexagonal socket 10 65 10 985329
5/16" Hexagonal socket 12 65 12 996178
8 mm Hexagonal socket 13 65 13 996179
10 mm Hexagonal socket (small type) 14 65 14 996180
10 mm Hexagonal socket 16 65 16 996181
10 mm Hexagonal socket 17 65 17 996182
1/2" Hexagonal long socket 21 166 21 996197
BL
Engraved characters
4. Drill chuck adapter set: Code No. 321823
Use the drill available on the market.
NOTE
SpeciïŹ cations are subject to change without any
obligation on the part of the metabo HPT.
OPTIONAL ACCESSORIES.....sold separately
24
English
Produktspezifikationen
| Marke: | Metabo |
| Kategorie: | Bohrmaschine |
| Modell: | WH36DC |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Metabo WH36DC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Bohrmaschine Metabo
25 Mai 2024
10 Mai 2024
4 Mai 2024
4 Mai 2024
30 April 2024
29 April 2024
29 April 2024
25 April 2024
8 April 2024
2 April 2024
Bedienungsanleitung Bohrmaschine
- Bohrmaschine Panasonic
- Bohrmaschine Cotech
- Bohrmaschine Makita
- Bohrmaschine Bosch
- Bohrmaschine Flex
- Bohrmaschine Parkside
- Bohrmaschine Vonroc
- Bohrmaschine AEG
- Bohrmaschine Velleman
- Bohrmaschine IKEA
- Bohrmaschine Black And Decker
- Bohrmaschine Cocraft
- Bohrmaschine FERM
- Bohrmaschine Ryobi
- Bohrmaschine Skil
- Bohrmaschine Trotec
- Bohrmaschine Baier
- Bohrmaschine Carat
- Bohrmaschine Hilti
- Bohrmaschine Sparky
- Bohrmaschine DeWalt
- Bohrmaschine Einhell
- Bohrmaschine Elu
- Bohrmaschine Festool
- Bohrmaschine Worx
- Bohrmaschine Tacklife
- Bohrmaschine Hikoki
- Bohrmaschine Hitachi
- Bohrmaschine Hyundai
- Bohrmaschine Hazet
- Bohrmaschine Kinzo
- Bohrmaschine Kress
- Bohrmaschine Stanley
- Bohrmaschine GĂŒde
- Bohrmaschine Power Craft
- Bohrmaschine Workzone
- Bohrmaschine Meec Tools
- Bohrmaschine Dremel
- Bohrmaschine Fieldmann
- Bohrmaschine Proxxon
- Bohrmaschine Berner
- Bohrmaschine Westfalia
- Bohrmaschine Stihl
- Bohrmaschine Dedra
- Bohrmaschine DURO
- Bohrmaschine Graphite
- Bohrmaschine Pattfield
- Bohrmaschine Silverline
- Bohrmaschine Holzmann
- Bohrmaschine Sthor
- Bohrmaschine Herkules
- Bohrmaschine Robust
- Bohrmaschine Zipper
- Bohrmaschine Yato
- Bohrmaschine Baumr-AG
- Bohrmaschine Genesis
- Bohrmaschine Festo
- Bohrmaschine Delta
- Bohrmaschine Batavia
- Bohrmaschine Bavaria
- Bohrmaschine Milwaukee
- Bohrmaschine Narex
- Bohrmaschine Toolcraft
- Bohrmaschine Fein
- Bohrmaschine Gardena
- Bohrmaschine Craftsman
- Bohrmaschine Defort
- Bohrmaschine Powerplus
- Bohrmaschine Alpha Tools
- Bohrmaschine Ozito
- Bohrmaschine Sun Joe
- Bohrmaschine Ridgid
- Bohrmaschine Porter-Cable
- Bohrmaschine Guede
- Bohrmaschine Felisatti
- Bohrmaschine Gamma
- Bohrmaschine Global
- Bohrmaschine Lux Tools
- Bohrmaschine Tanaka
- Bohrmaschine Wolfcraft
- Bohrmaschine Meister Craft
- Bohrmaschine Truper
- Bohrmaschine Kreg
- Bohrmaschine Einhell Bavaria
- Bohrmaschine Prowork
- Bohrmaschine Bullcraft
- Bohrmaschine Tryton
- Bohrmaschine Ergotools Pattfield
- Bohrmaschine THUN
- Bohrmaschine Bavaria By Einhell
Neueste Bedienungsanleitung fĂŒr -Kategorien-
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
4 Dezember 2024
3 Dezember 2024