Makita MLS100N Bedienungsanleitung
Makita
Sägemaschine
MLS100N
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita MLS100N (16 Seiten) in der Kategorie Sägemaschine. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/16
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
Compound Miter Saw
MLS100
015058
IMPORTANT: Read Before Using.
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model MLS100
Blade diameter 255 mm
Blade body thickness 1.6 mm - 2.4 mm
Hole diameter
For all countries other than European countries 25.4 mm
For European countries 30 mm
Max. Cutting capacities (H x W) with blade 255 mm in diameter
Miter angle
Bevel angle 0° 45° (left and right)
0° 75 mm x 130 mm 75 mm x 90 mm
45° (left) 48 mm x 120 mm 48 mm x 90 mm
No load speed (min-1) 4,200
Dimensions (L x W x H) 610 mm x 485 mm x 515 mm
Net weight 14.7 kg
Safety class /II
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END217-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･ DOUBLE INSULATION
･ To avoid injury from flying debris, keep
holding the saw head down, after
making cuts, until the blade has come
to a complete stop.
･ Do not place hand or fingers close to
the blade.
･ For your safety, remove the chips, small
pieces, etc. from the table top before
operation.
･ Always set SUB-FENCE to left position
when performing left bevel cuts. Failure
to do so may cause serious injury to
operator.
･ To loosen the bolt, turn it clockwise.
･ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of the European
Directive, on Waste Electric and
Electronic Equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
ENE004-1
Intended use
The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN61029:
Sound pressure level (L
pA) : 92 dB (A)
Sound power level (L
WA) : 105 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
ENH003-15
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Compound Miter Saw
Model No./ Type: MLS100
3
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN61029
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
30.5.2014
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
GEA005-3
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.
Loose clothes, jewellery
or long hair can be caught in moving parts.
17.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of
dust collection can reduce dust-related hazards.
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
Produktspezifikationen
| Marke: | Makita |
| Kategorie: | Sägemaschine |
| Modell: | MLS100N |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Makita MLS100N benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sägemaschine Makita
15 Oktober 2024
12 Oktober 2024
3 Oktober 2024
2 Oktober 2024
30 September 2024
30 September 2024
24 September 2024
15 September 2024
31 August 2024
31 August 2024
Bedienungsanleitung Sägemaschine
- Sägemaschine Brennenstuhl
- Sägemaschine Cotech
- Sägemaschine Royal Catering
- Sägemaschine Bosch
- Sägemaschine Flex
- Sägemaschine Parkside
- Sägemaschine Vonroc
- Sägemaschine AEG
- Sägemaschine Black And Decker
- Sägemaschine Cocraft
- Sägemaschine FERM
- Sägemaschine Ryobi
- Sägemaschine Skil
- Sägemaschine Topcraft
- Sägemaschine Trotec
- Sägemaschine Maestro
- Sägemaschine Prime3
- Sägemaschine Hilti
- Sägemaschine Bort
- Sägemaschine DeWalt
- Sägemaschine Einhell
- Sägemaschine Elu
- Sägemaschine Festool
- Sägemaschine Mafell
- Sägemaschine Maktec
- Sägemaschine Worx
- Sägemaschine Luxor
- Sägemaschine Tacklife
- Sägemaschine Hikoki
- Sägemaschine Hitachi
- Sägemaschine Hyundai
- Sägemaschine Fuxtec
- Sägemaschine Kress
- Sägemaschine Max
- Sägemaschine Metabo
- Sägemaschine Stanley
- Sägemaschine Atika
- Sägemaschine Güde
- Sägemaschine Power Craft
- Sägemaschine Scheppach
- Sägemaschine Workzone
- Sägemaschine Biltema
- Sägemaschine Meec Tools
- Sägemaschine Dremel
- Sägemaschine Fieldmann
- Sägemaschine King Craft
- Sägemaschine Proxxon
- Sägemaschine Westfalia
- Sägemaschine Remington
- Sägemaschine Husqvarna
- Sägemaschine Stihl
- Sägemaschine Dedra
- Sägemaschine DURO
- Sägemaschine Graphite
- Sägemaschine Pattfield
- Sägemaschine Silverline
- Sägemaschine Holzmann
- Sägemaschine MSW
- Sägemaschine Florabest
- Sägemaschine Germania
- Sägemaschine Stiga
- Sägemaschine Hammer
- Sägemaschine ACG
- Sägemaschine Greenworks
- Sägemaschine Huvema
- Sägemaschine Robust
- Sägemaschine Zipper
- Sägemaschine Yato
- Sägemaschine Baumr-AG
- Sägemaschine Genesis
- Sägemaschine BluCave
- Sägemaschine Morrison
- Sägemaschine Batavia
- Sägemaschine Evolution
- Sägemaschine Matrix
- Sägemaschine Dolmar
- Sägemaschine Bavaria
- Sägemaschine Brüder Mannesmann
- Sägemaschine Milwaukee
- Sägemaschine Narex
- Sägemaschine Toolcraft
- Sägemaschine Fein
- Sägemaschine AL-KO
- Sägemaschine EGO
- Sägemaschine CMI
- Sägemaschine IDEAL
- Sägemaschine Cobra
- Sägemaschine Verto
- Sägemaschine Craftsman
- Sägemaschine Powerplus
- Sägemaschine Alpha Tools
- Sägemaschine Echo
- Sägemaschine Elektra Beckum
- Sägemaschine Toledo
- Sägemaschine McCulloch
- Sägemaschine Ozito
- Sägemaschine Yard Force
- Sägemaschine Sun Joe
- Sägemaschine Solo
- Sägemaschine Texas
- Sägemaschine Oregon Scientific
- Sägemaschine Ridgid
- Sägemaschine Porter-Cable
- Sägemaschine VARO
- Sägemaschine Spear & Jackson
- Sägemaschine Duro Pro
- Sägemaschine Erbauer
- Sägemaschine Ergofix
- Sägemaschine Exakt
- Sägemaschine Ferrex
- Sägemaschine FOM
- Sägemaschine Gamma
- Sägemaschine Gardenline
- Sägemaschine Global
- Sägemaschine Goon
- Sägemaschine Grizzly
- Sägemaschine Gude Pro
- Sägemaschine HURRICANE
- Sägemaschine Kompernass
- Sägemaschine Lux Tools
- Sägemaschine Max Bahr
- Sägemaschine Maxx
- Sägemaschine Qualcast
- Sägemaschine Tanaka
- Sägemaschine Toolson
- Sägemaschine Troy-Bilt
- Sägemaschine Avantco
- Sägemaschine Wolfcraft
- Sägemaschine Masport
- Sägemaschine Garland
- Sägemaschine Meister Craft
- Sägemaschine Clarke
- Sägemaschine Powerworks
- Sägemaschine Sovereign
- Sägemaschine Challenge
- Sägemaschine Challenge Xtreme
- Sägemaschine Truper
- Sägemaschine Łucznik
- Sägemaschine Vulcan
- Sägemaschine MacAllister
- Sägemaschine RIKON
- Sägemaschine Backyard Pro Butcher Series
- Sägemaschine Kreg
- Sägemaschine Jonsered
- Sägemaschine Einhell Bavaria
- Sägemaschine Proviel
- Sägemaschine Budget
- Sägemaschine Tryton
- Sägemaschine MTM
- Sägemaschine EFA
- Sägemaschine MyTool
- Sägemaschine McKenzie
- Sägemaschine Anova
- Sägemaschine Yellow Garden Line
- Sägemaschine Ergotools Pattfield
- Sägemaschine IKRA
- Sägemaschine FIXIT
- Sägemaschine Bestgreen
- Sägemaschine BGU
- Sägemaschine Power Smart
- Sägemaschine Ultranatura
- Sägemaschine TAURUS Titanium
- Sägemaschine Maxbear
- Sägemaschine Extralink
- Sägemaschine Stalco
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
14 Oktober 2024
12 Oktober 2024
11 Oktober 2024
10 Oktober 2024
8 Oktober 2024