Makita 6802BV Bedienungsanleitung
Makita
Drehmaschine
6802BV
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita 6802BV (32 Seiten) in der Kategorie Drehmaschine. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/32
GB
Screwdriver Instruction Manual
F
Visseuse Manuel d’Instructions
D
Schrauber Betriebsanleitung
I
Avvitatrice Istruzioni d’Uso
NL
Schroevedraaier Gebruiksaanwijzing
E
Atornillador Manual de Instrucciones
P
Aparafusadora Manual de Instruço˜ es
DK
Skruemaskine Brugsanvisning
S
Skruvdragare Bruksanvisning
N
Skrutrekker Bruksanvisning
SF
Ruuvinväännin Käyttöohje
GR ∫·ÙÛ·‚›‰È √‰ËÁ›Â˜ ÃÚ‹Ûˆ˜
6802BV
1 2
3 4
5 6
7 8
2
ENGLISH Explanation of general view
1Locking position
2Locator
3Locking sleeve
4Magnetic socket bit
5Gear housing
6Socket bit
7Low
8High
9Speed control screw
0Switch trigger
qLock button
wReversing switch lever
eInsert bit
rMagnetic bit holder
SPECIFICATIONS
Capacities
Self drilling screw .......................................... 6 mm
Bit shank size ............................................. 1/4’’ Hex
No load speed (RPM) ................................ 0 – 2,500
Overall length ............................................... 265 mm
Net weight ....................................................... 1.7 kg
•Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
•Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Always be sure you have a firm footing.
Be sure no one is below when using the
machine in high locations.
2. Hold the machine firmly.
3. Keep hands away from rotating parts.
4. When driving into walls, floors or wherever
‘‘live’’ electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine by the insulated grasping
surfaces to prevent electric shock if you drive
into a ‘‘live’’ wire.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Removing or installing locator assembly
(Fig. 1)
To remove the locator assembly, pull the locking
sleeve forward and then turn it counterclockwise. To
install the locator assembly, screw it clockwise and
then push the locking sleeve back in lightly toward the
motor. Turn the locking sleeve slightly to match the
locking positions and then push in firmly to lock the
locator in place.
Removing or installing magnetic socket bit
(Fig. 2)
Important:
Always be sure that the machine is switched off and
unplugged before removing or installing the bit.
After removing the locator assembly, pull firmly to
remove the magnetic socket bit. To install the bit,
insert it into the machine as far as it will go.
Depth adjustment (Fig. 3 & 4)
Pull the locking sleeve forward and then turn it to
adjust the depth.
Initially, adjust the locator assembly to create a dis-
tance of approximately 0.5 mm from the tip of the
locator to the tip of the socket bit. One full turn of the
locator equals 1.5 mm change in depth. After adjust-
ing the locator assembly, push the locking sleeve in to
lock the locator in place. Drive a trial screw into your
material or a piece of duplicate material. If the depth
is not suitable for the screw, continue adjusting until
the proper depth setting is obtained.
Switch action (Fig. 5)
CAUTION:
Before plugging in the machine, always check to see
that the switch trigger actuates properly and returns to
the ‘‘OFF’’ position when released.
To start the machine, simply pull the trigger. Machine
speed is increased by increasing pressure on the
trigger. Release the trigger to stop. For continuous
operation, pull the trigger and then push in the lock
button. To stop the machine from the locked position,
pull the trigger fully, then release it. A speed control
screw is provided so that maximum machine speed
can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclock-
wise for lower speed.
NOTE:
Even with the switch on and motor running, the bit will
not rotate until you fit the point of the bit in the screw
head and apply forward pressure to engage the
clutch.
3
Produktspezifikationen
| Marke: | Makita |
| Kategorie: | Drehmaschine |
| Modell: | 6802BV |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Makita 6802BV benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Drehmaschine Makita
25 Mai 2024
23 Mai 2024
23 Mai 2024
23 Mai 2024
19 Mai 2024
13 Mai 2024
13 Mai 2024
12 Mai 2024
11 Mai 2024
7 Mai 2024
Bedienungsanleitung Drehmaschine
- Drehmaschine Basetech
- Drehmaschine Panasonic
- Drehmaschine Bosch
- Drehmaschine Parkside
- Drehmaschine Vonroc
- Drehmaschine AEG
- Drehmaschine Powerfix
- Drehmaschine EMOS
- Drehmaschine Black And Decker
- Drehmaschine Cocraft
- Drehmaschine FERM
- Drehmaschine Ryobi
- Drehmaschine Skil
- Drehmaschine Trotec
- Drehmaschine Carrera
- Drehmaschine Hilti
- Drehmaschine DeWalt
- Drehmaschine Einhell
- Drehmaschine Elu
- Drehmaschine Festool
- Drehmaschine Worx
- Drehmaschine Kraftwerk
- Drehmaschine Hikoki
- Drehmaschine Hitachi
- Drehmaschine Hazet
- Drehmaschine Kress
- Drehmaschine Metabo
- Drehmaschine Stanley
- Drehmaschine Güde
- Drehmaschine Biltema
- Drehmaschine Meec Tools
- Drehmaschine Dremel
- Drehmaschine Fieldmann
- Drehmaschine Beta
- Drehmaschine Westfalia
- Drehmaschine Chicago Pneumatic
- Drehmaschine Dedra
- Drehmaschine Silverline
- Drehmaschine Sthor
- Drehmaschine Yato
- Drehmaschine Pansam
- Drehmaschine Bavaria
- Drehmaschine Brüder Mannesmann
- Drehmaschine Milwaukee
- Drehmaschine Toolcraft
- Drehmaschine Chamberlain
- Drehmaschine Fein
- Drehmaschine Bonus
- Drehmaschine Craftsman
- Drehmaschine Powerplus
- Drehmaschine Ozito
- Drehmaschine Porter-Cable
- Drehmaschine Steren
- Drehmaschine Wiha
- Drehmaschine StarTech.com
- Drehmaschine Meister Craft
- Drehmaschine Truper
- Drehmaschine Park Tool
- Drehmaschine XU1
- Drehmaschine Urrea
- Drehmaschine Wera
- Drehmaschine VOREL
- Drehmaschine Netter Vibration
- Drehmaschine Rodcraft
- Drehmaschine Bavaria By Einhell
- Drehmaschine SW-Stahl
Neueste Bedienungsanleitung für -Kategorien-
26 Juni 2024
26 Juni 2024
21 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024