Lowrance LDT3200 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lowrance LDT3200 (12 Seiten) in der Kategorie Navigator. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
1
Pub. 988-0099-071
LDT-3200
Digital Temperature Gauge
Installation & Operation Instructions
The LDT-3200 combines a temperature gauge, voltmeter and clock in one
housing. It displays the temperature in either Fahrenheit °F or Celsius
°C and may be set to rotate between four gauge displays or "pages." The
unit fits in a standard 2-1/8" (54 mm) hole used by most marine equip-
ment manufacturers.
The gauge and its temperature sensor are designed to show surface water
temperature in a transom installation, but the sensor can be installed to
monitor the temperature elsewhere, such as in a live well.
LDT-3200 temperature gauge.
Mounting Preparations
When installed, the gauge will cover an area on the dash 2-3/8" (60.3 mm)
in diameter. To mount the unit, first make sure there is at least 2-3/4"
(70 mm) from the front of the dash to any obstruction behind the dash.
The maximum usable dash thickness is 1-1/8" (28.5 mm). Also, be sure
there is room to route the power and sensor cables. The following figure
shows gauge dimensions.
2
Dash installation, cross-section view.
Caution:
You should read over the entire installation section before drilling
any holes in your vessel!
You can install this gauge in some other order if you prefer, but we rec-
ommend this installation sequence, which is summarized below:
1. Determine the location for the gauge so you can plan how and where to
route the cables. This will help you make sure you have enough cable
length for the desired configuration.
2. Determine the location of your battery or other power connections,
along with the power cable route.
3. Determine the location for the temperature sensor and its cable route.
4. Determine the location for the alarm buzzer and its wire route.
5. If you want to turn on the gauge backlights whenever you turn on your
dashboard lights, locate your boat's dash light switch and determine how
to route the dash light wires to it.
6. Install the temp sensor, connect power wires to the battery and route
the power/sensor cable to the gauge location.
7. Install the gauge, and connect the power/sensor cable.
8. Connect the buzzer wires and install the buzzer. If desired, connect the
dash light wires to the boat's dash light switch.
2-3/4"
(70 mm)
2-3/8"
(60.3 mm)
Gasket
Threaded mounting collar
Dash
Cables
3
Recommended Tools and Supplies
Supplies are not included, unless otherwise indicated. A transom mount
requires one #8 stainless steel screw (3/4" long) and a high quality, ma-
rine-grade above- or below-waterline sealant/adhesive compound. If you
want to make a pilot hole for the screw, use a drill and a 1/8" drill bit. If
you prefer the option of routing the temp sensor cable through the tran-
som (instead of over it), you will also need a 1/2" drill bit.
If the dash does not have a standard 2-1/8" (54 mm) hole, you will need a
drill or saw to make the hole. Carefully measure the dash thickness and
the hole area before cutting or drilling.
A screwdriver is needed for mounting the temp sensor. The buzzer in-
stallation requires two cable ties.
If you need to extend any of the wires, use a minimum of 24 gauge wire
and wire connectors of your choice. Wire nuts or electrical tape are re-
quired to cap any unused bare wires.
Mounting
The temperature sensor can be mounted in any convenient location.
However, make sure it is placed on the transom where it will be in con-
tact with the water at all times. Make sure the location does not interfere
with the boat's trailer.
Temp sensor on transom, with cable routed through the transom.
After determining the location, use the sensor as a template and mark
the hull for the screw's pilot hole, if desired. Route the sensor and cable
over or through the transom to the mounting location. If routing through
the transom, drill a 1/2" hole to accommodate the sensor. Attach the sen-
sor to the hull with one #8 stainless steel screw, then seal the screw with
the below-waterline sealant compound.
Caution:
If you drill a hole in the transom for the cable, make sure it is lo-
cated above the waterline. After installation, be sure to seal the ca-
ble hole with the same marine grade above-or below-waterline
sealant used for the screw.
Produktspezifikationen
| Marke: | Lowrance |
| Kategorie: | Navigator |
| Modell: | LDT3200 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Lowrance LDT3200 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Navigator Lowrance
5 September 2024
5 September 2024
2 September 2024
10 August 2024
4 August 2024
3 August 2024
31 Juli 2024
30 Juli 2024
29 Juli 2024
28 Juli 2024
Bedienungsanleitung Navigator
- Navigator Humminbird
- Navigator Clatronic
- Navigator Acer
- Navigator Asus
- Navigator Sanyo
- Navigator Medion
- Navigator Philips
- Navigator SilverCrest
- Navigator Sony
- Navigator Conrad
- Navigator MarQuant
- Navigator Thomson
- Navigator Blaupunkt
- Navigator Grundig
- Navigator Kenwood
- Navigator Pyle
- Navigator ARCHOS
- Navigator Caliber
- Navigator Pioneer
- Navigator JVC
- Navigator Motorola
- Navigator Nokia
- Navigator Dual
- Navigator Hitachi
- Navigator Skoda
- Navigator Garmin
- Navigator GOCLEVER
- Navigator Mio
- Navigator Bushnell
- Navigator Teasi
- Navigator Harman Kardon
- Navigator Scosche
- Navigator Furuno
- Navigator Simrad
- Navigator BMW
- Navigator Honda
- Navigator Parrot
- Navigator Zebra
- Navigator Audi
- Navigator Midland
- Navigator Binatone
- Navigator Hagenuk
- Navigator Alpine
- Navigator Volkswagen
- Navigator Volvo
- Navigator Toyota
- Navigator Kia
- Navigator Overmax
- Navigator Kalkhoff
- Navigator Airis
- Navigator Packard Bell
- Navigator XZENT
- Navigator Uniden
- Navigator Clarion
- Navigator Sylvania
- Navigator Audiovox
- Navigator Becker
- Navigator CarTrek
- Navigator ESX
- Navigator Falk
- Navigator Magellan
- Navigator NAVIGON
- Navigator Navitel
- Navigator Navman
- Navigator TomTom
- Navigator ViaMichelin
- Navigator Zenec
- Navigator Cobra
- Navigator VDO
- Navigator Insignia
- Navigator Celestron
- Navigator Autovision
- Navigator Prestigio
- Navigator Boss
- Navigator Mazda
- Navigator Jensen
- Navigator Alfa Romeo
- Navigator GlobalSat
- Navigator Danew
- Navigator Dynavin
- Navigator Eagle
- Navigator Eclipse
- Navigator Igo
- Navigator Kapsys
- Navigator Lanzar
- Navigator Nav N Go
- Navigator Raymarine
- Navigator Route 66
- Navigator Seecode
- Navigator Soundstream
- Navigator Sungoo
- Navigator Sygic
- Navigator VDO Dayton
- Navigator Chrysler
- Navigator Rosen
- Navigator ModeCom
- Navigator Amparos
- Navigator Lark
- Navigator Pharos
- Navigator V7
- Navigator Izzo Golf
- Navigator Cheetah
- Navigator Dashmate
- Navigator Planet Audio
- Navigator Voice Caddie
- Navigator Coyote Systems
- Navigator Rand McNally
- Navigator Whistler
- Navigator Cydle
- Navigator LXNAV
- Navigator SkyCaddie
- Navigator TELE System
- Navigator Zoleo
Neueste Bedienungsanleitung für -Kategorien-
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
12 Oktober 2024
12 Oktober 2024
9 Oktober 2024
9 Oktober 2024
8 Oktober 2024
8 Oktober 2024
7 Oktober 2024