Leviton 49990-LDL Bedienungsanleitung

Leviton Nicht kategorisiert 49990-LDL

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Leviton 49990-LDL (11 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/11

PK-A3141-10-02-5A

(REF-0R-49990-00 -06)-00



,>?@=04-0=!;?4.:990.?:=

%! &!$

%&

%%&

%

%

%%





%





%

%&R! &!$

A Division of Leviton Manufacturing Co.,Inc.

Technical Support: 800-824-3005

Fax: (425) 483-5270

www.levitonvoicedata.com

Description Part No.

Multimode ST Connector 50/125 & 62.5/125 49990-MST

Singlemode ST Connector 49990-SST

Multimode SC Connector 50/125 & 62.5/125 (beige) 49990-MSC

LO Multimode SC Connector (aqua) 49990-LSC

Singlemode SC Connector (blue) 49990-SSC

SC Duplex Clip, black (Bag of 25) 49886-DSC

Mulimode LC Connector with 3mm boot (beige) 49990-ML2

LO Multimode LC Connector with 3mm boot (aqua) 49990-LL2

Singlemode LC Connector with 3mm boot (blue) 49990-SL2

Multimode LC Connector with .9mm boot (beige) 49990-MDL

LO Multimode LC Connector with .9 mm boot (aqua) 49990-LDL

Singlemode LC Connector with .9mm boot (blue) 49990-SDL

LC Duplex Clip, Multimode, beige (bag of 25) 49886-DLM

LC Duplex Clip, Singlemode, blue (bag of 25) 49886-DLS

Fast Cure Tool Kit 49800-FTK

Fast Cure Consumables Kit 49800-FCC

Adhesive Primer Kit 49800-680

Crimp Tool with .128, .151, .178 hex die 49886-FCT

Replacement Needles (19 gauge, bags of 25) 49886-FCN

Syringes (bags of 25) 49886-SYR

LC Polishing Puck 49886-LCP

LC Duplex Scope Adapter 49886-LCD

LC Simplex Scope Adapter 49886-LCS

Fast Cure Carrying Case 49886-FCC

Part Numbers

! &!$

PK-A3141-10-02-5A

(REF-0R-49990-00- 06)00-



%&%)&





)&



'$



>>08-7D9>?=@.?4:9>

"$"$

77:990.?:=&D;0>

NOTE: If using 900 µm buffered fiber, do not use the crimp tube in step 1.

1. Slide the boot and the crimp tube onto the fiber, with the small end inserted first. (Figure 1)

:=88,.60?0/,-70Use the ribbed boot, provided.

:=S8@110=0/,-70Use the smooth boot, provided.

NOTE: If using an SC Connector on 900µm buffered fiber, you must install the SC body into the housing

before continuing to step 2. Align the body with the connector housing, then insert the body into

the housing until it snaps into place. Use the dust cap to push the body into the housing.

2. Strip the jacket and/or buffer using the measurements provided in the chart below, and strip in

increments of 1/4”. If using jacketed cable, trim the aramid strands as indicated, below.

(Figure 2a-c)

!&&:307;,A:4/?::7-@110=,9/14-0=.:9?,849,?4:9.70,95,.60?,9/0C;:>0/-@110=B4?3

,,7.:3:7B4;0?309B4?3,749?1=00B4;0-:?3-01:=0,9/,1?0=>?=4;;492

3. Clean exposed fiber with a 99% alcohol wipe followed by a lint-free wipe to remove any contaminants.

 !&8,20>,=09:??:>.,70

%:990.?:=&D;0>:988,.60?0/,-70! +

4. Insert spacer over buffer and push all the way down, until it rests against the jacket. (Figure 3)

7409? :?0> :?0>/07W@?474>,?0@= :?,>/07@>@,=4:

strip length 20 mm

1/4

3/4

1 3/4

1/2

1 1/2

apply primer 10mm



 !&8,20>,=09:??:>.,70

PK-A3141-10-02-5A

(REF-0R-49990-00- 06)00-





%%

77:990.?:=,9/4-0=&D;0>

1. Remove the dust cap from the connector.

2.2. Dry fit the fiber by inserting the fiber into the connector. This will assure that all coating has been

removed and the fiber can be inserted into the connector ferrule.

3. Shake the adhesive bottle before using. Remove the cap from the adhesive bottle, and attach the

needle by pressing it gently onto the top of the bottle until you feel it set into place.

NOTE: Syringes are also available for inserting adhesive.

4. Insert the needle and firmly hold it against the back of the connector while filling it. Being careful not to

overfill the connector, squeeze the bottle gently, injecting the adhesive into the connector. Continue

until a dot of adhesive is visible at the other end, then remove the needle. Wipe away excess adhesive

from the end of the ferrule.

5. Using the brush attached to the lid on the bottle of primer, apply the primer to the first 10mm of the

exposed fiber. See figure 2a.

6. Insert the fiber into the back of the connector. To prevent premature bonding, use continuous motion,

until the fiber is fully seated in the connector. The primer will activate adhesive and begin the bonding

process.

!&&3014-0=>3:@7/-049>0=?0/B4?349>0.:9/>:1;=48492

7. Hold the fiber in place for 10-20 seconds, and allow up to 3 minutes for the adhesive to bond.

8. If using any cable type but jacketed fiber, slide the boot back up over the back of the connector, now. If

using jacketed fiber, follow the steps, below.

//4?4:9,7%?0;>:=88,.60?0/,-70! +

9. Arrange the aramid strands evenly around the end of the connector, then slide the crimp tube over the

aramid strands and connector. Using a crimp tool, crimp the tube at both the large end (step 1) and the

small end (step 2). (Figure 4)

%&%7,=2009/Use the .178” hex die.

%&%>8,7709/Use the .151” hex die.

Use the .128” hex die.



7409? :?0> :?0>/07W@?474>,?0@= :?,>/07@>@,=4:



Produktspezifikationen

Marke:	Leviton
Kategorie:	Nicht kategorisiert
Modell:	49990-LDL
Produktfarbe:	Aqua-Farbe
Ursprungsland:	Taiwan
Menge pro Packung:	1 Stück(e)
Nachhaltigkeitskonformität:	Ja
Nachhaltigkeitszertifikate:	RoHS
Steckerverbindergeschlecht:	Männlich
Lichtleitertyp:	OM3/OM4
Kabel mode struktur:	Multi-Modus
Verbindungstyp:	LC